《JIS-C-5101-14-1-1998-R2004-ENG.pdf》由会员分享，可在线阅读，更多相关《JIS-C-5101-14-1-1998-R2004-ENG.pdf（19页珍藏版）》请在三一文库上搜索。
1、. . 1 JIS C 5101-14-1 :1998 (IEC 60384-14-1 : 1993) J IS JAPANESE I NDUSTRIAL STANDARD Translated and Published by Ja pa nese Stand a rds Ascoci a tion Fixed capacitors for use in electronic equipment Part 14 : Blank detail specification : Fixed capacitors for electromagnetic interference suppressio
2、n and connection to the supply mains Assessment level D ICs 31.060.iO Descriptors : capacitors, fixed capacitors, electronic equipment and components, electrica faults, electromagnetism, electromagnetic radiation, electronic power supplies, interference suppression, ratings Reference number : JIS C
3、5101-14-1 : 1998 (E) 10 s Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/15/2007 08:01:35 MDTNo reproduction or networking permitted without license from IHS -,-,- STDOJIS C 5LOL-L4-L-ENGL 3998 11
4、11 4933608 05b2783 2T5 m C 5101-14-1 : 1998 (IEC 60384-14-1 : 1993) Date of Establishment: 1998-07-20 Date of Public Notice in Official Gazette: 1998-07-21 Investigated by: Japanese Industrial Standards Committee Divisional Council on Electronics . . JIS C 5101-14-1 : 1998, First English edition pub
5、lished in 2000-05 Translated and published by: Japanese Standards Association 4-1-24, Akasaka, Minato-ku, Tokyo, 107-8440 JAPAN In the event of any doubts arising as to the contents, the original JIS is to be the final authority. O JCA 2000 Ali rights reserved. Unless otherwise specified, no part of
6、 this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. Printed in Japan Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS
7、Employees/1111111001, User=Wing, Bernie Not for Resale, 03/15/2007 08:01:35 MDTNo reproduction or networking permitted without license from IHS -,-,- STD=JIS C SLOL-L+-L-ENGL 1998 - 4933608 0562784 I32 . . C 5101-14-1 1998 (IEC 60384-14-1 : 1993) Foreword This translation has been made based on the
8、original Japanese Industrial Standard established by the Minister of International Trade and Industry through deliberations at Japanese Industrial Standards Committee in accordance with the Industrial Standardization Law: Attention shall be drawn to the possibility that a part of this Standard may c
9、onflict with a patent right, application for a patent right after opening to the public, utility model right (including those applied before 1993-12-31) or application for registration of utility model after opening to the public which have technical properties. The Minister of International Trade a
10、nd Industry and the Japanese Industrial Standards Committee are not responsible for identifying the patent right, application for a patent right after opened, utility model right or application for registration of utility model after opening to the public which have the technical properties of this
11、kind. Group standards The following standards form the specifications for the group of element specified in this Standard. JIS C 5101 JIS C 5101-1 JIS C 5101-2 JIS C 5101-2-1 JIS C 5101-3 JIS C 5101-3-1 JIS C 5101-4 JIS C 5101-4-1 JIS C 5101-4-2 JIS C 5101-8 JIS C 5101-8-1 JIS C 5101-9 JIS C 5101-9-
12、1 JIS C 5101-10 JIS C 5101-10-1 JIS C 5101-11 General rules of fixed capacitors for use in electronic equipment Part 1: Generic specification Part 2: Sectional specification: Fixed metallized polyethylene- terephthalate film dielectric d.c. capacitors Part 2: Blank detail specification: Fixed metall
13、ized polyethylene- terephthalate film dielectric d.c. capacitors. Assessment level E Part 3: Sectional specification: Fixed tanta1 um chip capacitors Part 3: Blank. detail specification: Fixed tantalum chip capacitors. Assessment level E Part 4: Sectional specification: Aluminium electrolytic capaci
14、tors with solid and non-solid electrolyte Part 4 : Blank detail specification: Aluminium electrolytic capacitors with non-solid electrolyte. Assessment level E Part 4: Blank detail specification: Aluminium electrolytic capacitors with solid electrolyte. Assessment level E Part 8: Sectional specifica
15、tion: Fixed capacitors of ceramic dielectric, Class 1 Part 8: Blank detail specification: Fixed capacitors of ceramic dielectric, class 1. Assessment level E Part 9: Sectional specification: Fixed capacitors of ceramic dielectric, Class 2 Part 9: Blank detail specification: Fixed capacitors of ceram
16、ic dielectric, class 2. Assessment level E Part 1 O: Sectional specification: Fixed multilayer ceramic chip capacitors Part 10: Blank detail specification: Fixed multilayer ceramic chip capacitors. Assessment level E Part 11: Sectional specification: Fixed polyethylene-terephthalate film dielectric
17、metal foil d.c. capacitors Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/15/2007 08:01:35 MDTNo reproduction or networking permitted without license from IHS -,-,- C 5101-14-1 : 1998 (IEC 60384-1
18、4-1 : 1993) JIS C 5101-11-1 JIS C 5101-13 JIS C 5101-13-1 JIS C 5101-14 JIS C 5101-14-1 JIS C 5101-15 JIS C 5101-15-1 JIS C 5101-15-2 JIS C 5101-15-3 JIS C 5101-16 JIS C 5101-16-1 JIS C 5101-17 JIS C 5101-17-1 JIS C 5101-18 JIS C 5101-18-1 JIS C 5101-18-2 JIS C 5101-20 JIS C 5101-20-1 Part 11: Blank
19、 detail specification: Fixed polyethylene-terephthalate film dielectric metal foil d.c. capacitors. Assessment level E Part 13: Sectional specification: Fixed polypropylene film dielectric metal foil d.c. capacitors Part 13: Blank detail specification: Fixed polypropylene film dielectric metal foil
20、d.c. capacitors. Assessment level E Part 14: Sectional specification: Fixed capacitors for electromagnetic interference suppression and connection to the supply mains Part 14: Blank detail specification: Fixed capacitors for electromagnetic interference suppression and connection to the supply mains
21、. Assessment level D Part 15: Sectional specification: Fixed tantalum capacitors with non-solid or solid electrolyte Part 15: Blank detail specification: Fixed tantalum capacitors with non-solid electrolyte and foil electrode. Assessment level E Part 15: Blank detail specification: Fixed tantalum ca
22、pacitors with non-solid electrolyte and porous anode. Assessment level E Part 15: Blank detail specification: Fixed tantalum capacitors with solid electrolyte and porous anode. Assessment level E Part 16: Sectional specification: Fixed metallized polypropylene film dielectric d.c. capacitors Part 16
23、: Blank detail specification: Fixed metallized polypropylene film dielectric d.c. capacitors. Assessment level E Part 17: Sectional specification: Fixed metallized polypropylene film dielectric a.c. and pulse capacitors Part 17: Blank detail specification: Fixed metallized polypropylene film dielect
24、ric a.c. and pulse capacitors. Assessment level E Part 18: Sectional specification: Fixed aluminium electrolytic chip capacitors with solid and non-solid electrolyte Part 18: Blank detail specification: Fixed aluminium electrolytic chip capacitors with solid electrolyte. Assessment level E Part 18:
25、Blank detail specification: Fixed aluminium electrolytic chip capacitors with non-solid electrolyte. Assessment level E Part 20: Sectional specification: Fixed metallized polyphenylene sulfide film dielectric chip d.c. capacitors Part 20: Blank detail specification: Fixed metallized polyphenylene su
26、lfide film dielectric chip d.c. capacitors. Assessment level EZ * . Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/15/2007 08:01:35 MDTNo reproduction or networking permitted without license from
27、IHS -,-,- C 5101-14-1 1998 (IEC 60384-14-1 : 1993) Contents Page Introduction . 1 Blank detail specification 1 Identification of the detail specification . 1 2 Identification of the capacitor Section one-General data 1 General data . 1.0 Scope 1.1 1.2 Dimensions Recommended method(s) of mounting (to
28、 be inserted) . 1.3 Ratings and characteristics . 1.4 Normative references 1.5 Marking . 1.6 Ordering information 1.7 Certified records of released lots I 1.8 1.9 Additional information (not for inspection purposes) . Additional or increased severities or requirements to those specified in the gener
29、ic and/or sectional specification 4 5 5 Section two-Inspection requirements 2 Inspection requirements . 6 2.1 Procedures . 6 Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/15/2007 08:01:35 MDTNo r
30、eproduction or networking permitted without license from IHS -,-,- STD*JIS C 5LOL-14-L-ENGL 1998 = 4933608 05b2787 940 JAPANESE INDUSTRIAL STANDARD JIS C 5101-14-1 : 1998 (IEC 60384-14-1 : 1993) Fixed capacitors for use in electronic equipment Fixed capacitors for electromagnetic interference suppre
31、ssion and connection to the supply mains Assessment level D Part 14 : Blank detail specification : Introduction This Japanese Industrial Standard has been prepared based on the first edition issued in 1993 of IEC 60384-14-1, Fixed capacitorsfor use in electronic equipment Part 2 4 :Blank detail spec
32、ification :Fixed capacitors for electromagnetic interference suppression and connection to the supply mains Assessment level O, without changing the technical contents. Those underlined passages by dotted lines in this Standard are not stated in the original IEC Standard. IEC Standards referred here
33、in are assigned numbers in _ - - _ _ _ _ _ _ _ - _ _ - - - - - - - - - - - - - - - - - accordance with the new numbering sy,-m-ofI-EC_SLandaqds pUJjn-forcg-o-n J3nu- ary Ist, 1997. As for the standards published before said date, their numbers have been changed to 60000 added to the former numbers,
34、but this does not make any _ - _ _ - _ _ _ - _ _ _ _ _ _ - - - - _ - - - - - - - - - - - - - - - - - - - _ _ - - _ _ - - _ _ - _ _ _ _ _ _ _ - - - - - - - _ - - - - _ - - - - - - _ - - - - - - - - - - - - _ - - - - - - - - - - - - - - - - - - - - - - - _ - - _ - - - - - Blank detail specification A
35、Blank detail specification is a supplementary docu- ment to the Sectional Specification JIS C 5101 - 14 and contains requirements for style, layout and minimum content of detail specifications. Detail specifications not complying with these requirements may not be considered as being in accor- dance
36、 with JIS specifications nor shall they so be described. In the preparation of detail specification the content of 1.4 of the sectional The numbers between brackets in the table on the second page (to be the first page of the detail specification) correspond to the following items of information whi
37、ch shall be inserted in the position indicated. specification shall be taken into account. Identification of the detail specification (1) The National Standards Organization or the “International Electrotechnical Commission” under whose authority the detail specification is drafted. (2) The National
38、 Standards or IEC number of the detail specification, date of issue and any further information required by the national system. (3) The number and issue number of the national or IEC Generic Specification. (4) The National or IEC number of the blank detail specification. Copyright Japanese Standard
39、s Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/15/2007 08:01:35 MDTNo reproduction or networking permitted without license from IHS -,-,- ,STD-JIS C 5101-14-1-ENGL 19% 4933h08 05h2788 887 I I 2 C 5101-14-1 1998 (IEC 60384-1
40、4-1:1993) Identification of the capacitor (5) A short description of the type of capacitor. (6) Information on typical construction (if applicable). Remarks: When the capacitor is not designed for use in printed board applica- tions, this shall be clearly stated in the detail specification this po-
41、sition. (7) Outline drawing with main dimensions which are of importance for inter- changeability and/or reference to the national or international documents for outlines. Alternatively, this drawing may be given in an Annex to the detail specification. (8) Application or group of applications cover
42、ed and/or assessment level. Remarks: The assessment level(s) to be used in a detail specification shall selected from the sectional specification JIS C 5101-14, 3.5.4. This implies that one blank detail specification may be used in combina- tion with several assessment levels, provided the grouping
43、of the tests does not change. (9) Reference data on the most important properties. e.g. JIS C 5101-1 : 1998 Fixed capa- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . citors for use in electronic equip- _ _ _ _ _ _ Part 1: generic _ _ _ _ - specification _ _ _ _ _ _ _ _ _ . . . . . . . .
44、. . . . . . . . . . . . . . . _ _ _ _ _ _ ment (2)- Outline drawing : (see Table I) (Third angle projection) (7) _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ (Other shapes are permitted within the dimensions given) Detail specification number (2) e.g. JIS C 5101-14-1 (4) QC 302401 (6) Explanation on constr
45、uction (8) Assessment level(s) : D * System (IECQ). _ _ - _ _ _ _ _ _ _ - _ _ _ Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/15/2007 08:01:35 MDTNo reproduction or networking permitted without l
46、icense from IHS -,-,- 3 C 5101-14-1 : 1998 (IEC 60384-14-1:1993) Information on the availability of components qualified to this detail specification is given in the Qualified Products List.(*) Note (*) This passage is applicable in case of IEC Quality Assessment System (IECQ). (9) Section One-Gener
47、al Data 1 General date 1.0 This blank detail specification is associated with the sectional specifi- cation, JIS C 5101-14, and specifies on the fixed capacitors for electromagnetic interference suppression and connection to the supply mains Assessment level D. Scope Remarks : This Standard correspo
48、nds to the following International Standard. IEC 60384-14- 1 : 1993 Fixed capacitors for use in electronic equip- ment Part 14 : Blank detail speci6cation : Fixed capacitors for electromagnetic inter- ference suppression and connection to the supply mains Assessment level D 1.1 Recommended method(s) of mounting (to be inserted) (See 1.4.2 of sectional specification, JIS C 5101- 14). 1.2 Dimensions Table I Dimensions _ _ _ _ _ _ _ _ _ _ _ _ I Dimensions (in mm or inches and mm) I Case size reference L, Remarks 1 When there is no case size reference, Table I may be om