《JIS-S-1039-2005-ENG.pdf》由会员分享，可在线阅读，更多相关《JIS-S-1039-2005-ENG.pdf（23页珍藏版）》请在三一文库上搜索。
1、JIS JAPANESE I NDUSTRIAL STANDARD Translated and Published by Japanese Standards Association JIS S 1039:2005 (JOIWJSA) Shelves and Racks ICs 97.140 Reference number : JIS S 1039 2005 (E) PROTECTED BY COPYRIGHT 13 S Copyright Japanese Standards Association Provided by IHS under license with JSALicens
2、ee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/15/2007 21:40:32 MDTNo reproduction or networking permitted without license from IHS -,-,- S 1039 2005 Foreword This translation has been made based on the original Japanese Indus- trial Standard revised by the Minister of Economy, Tr
3、ade and Industry through deliberations at the Japanese Industrial Standards Committee as the result of proposal for revision of Japanese Industrial Standard submitted by Japan Office & Institutional Furniture Association (JOIFA)/ Japanese Standards Association (JSA), draft being attached, based on t
4、he provision of Article 12 Clause 1 of the Industrial Standardization Law applicable to the case of revision by the provision of Article 14. Standards of JIS S 1039 and JIS S 1040 are unified at the time of revi- sion because of both standards having common elements such as similar principal constru
5、ction components such as column, shelf board, shelf board supporting equipment and so on, the uses of storage and archivirg goods on the shelf board, and so on. Consequently JIS S 104011994 is with drawn and JIS S 1039:1989 is re- vised and replaced with this Standard. Attention is drawn to the poss
6、ibility that some parts of this Standard may conflict with a patent right, application for a patent after opening to the public, utility model right or application for registration of utility model after opening to the public which have technical properties. The relevant Minister and the Japanese In
7、dustrial Standards Committee are not responsible for identi&ing the patent right, application for a patent after opening to the public, utility model right or application for registration of utility model after opening to the public which have the said technical properties. Date of Establishment: 19
8、69-01-01 Date of Revision: 2005-05-20 Date of Public Notice in Official Gazette: Investigated by: 2005-05-20 Japanese Industrial Standards Committee Standards Board Technical Committee on Consumer Life Products JIS S 1039 : 2005, First English edition published in 2005-10 Translated and published by
9、: Japanese Standards Association 4-1-24, Akasaka, Minato-ku, Tokyo, 107-8440 JAPAN In the event of any doubts arising as to the contents, the original JIS is to be the final authority. O JSA 2005 All rights reserved. Unless oterwise specified, no part of this publication may be reproduced or utilize
10、d in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. Printed in Japan PROTECTED BY COPYRIGHT Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, U
11、ser=Wing, Bernie Not for Resale, 03/15/2007 21:40:32 MDTNo reproduction or networking permitted without license from IHS -,-,- S 1039 2005 Contents 1 Scope 1 2 Normative references 1 3 Definitions 1 4 Classification 2 4.1 Classification by uses 2 4.2 Classification by structure 2 5 Dimensions 3 . .
12、. 6 Quality 3 6.1 Appearance 3 6.2 Performance 3 7 Structure 4 8 Materials 5 9 Tests 5 9.1 General test conditions 5 9.2 Stability test 6 9.3 Strength test 6 9.4 Surface treatment test 10 . . . 10 Inspection 11 11 Marking 11 12 - * 11 Annex 1 (informative) Terms of shelves and racks 14 Precautions t
13、o handling and maintenance control *. e - *. e - *. e - *. e - *. e - *. e - *. e - *. Annex 2 (informative) Dimension marking of shelves and racks 16 Annex 3 (informative) Overturn preventive devices for shelves and racks . 17 (i ) PROTECTED BY COPYRIGHT Copyright Japanese Standards Association Pro
14、vided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/15/2007 21:40:32 MDTNo reproduction or networking permitted without license from IHS -,-,- JAPANESE INDUSTRIAL STANDARD JIS S 1039 : 2005 Shelves and racks 1 referred to as “the shelves”. Scope
15、 This Japanese Industrial Standard specifies shelves and racks, hereafter Remarks Herein, shelves mean those capable of storing and archiving books, stationary, and business supplies constructed using the principal con- struction components such as columns, shelf boards, shelf board sup- porting equ
16、ipment in open-access style. 2 The standards listed in attached table 1 contain provisions which, through reference in this text, constitute provisions of this Standard. The most recent editions of the standard (including the amendments) shall be applied. Normative references Definitions For the pur
17、poses of this Standard, the following definitions apply. column shelf board board carrying goods (including the plane shapes such as net, flame, lattice and so on aiming to carry loads shelf board supporting equipment component supporting the shelf board top board board attached to the top of shelf
18、and not intending to support the goods independent type connecting function connecting type construction of the independent type consists of a single body and the connecting part which omits the column single type used from one direction double type shelf boards are equipped in two rows of front and
19、 rear and are used from both surfaces Shelf boards are movable separately from both sides. The lowest shelf may be one sheet of combination use in front and rear single column type columns double column type columns The lowest shelf may be supported by six or eight columns bay shelf mainly used to s
20、torage books, files, binders, document boxes, information filing goods and so on vertical component supporting the upper load complete with a single body itself as a construction and has no shelf boards are equipped in one row in the width direction and are the structure such that the shelf boards a
21、re supported by two the structure such that the shelf boards are supported by four unit of count in the width direction PROTECTED BY COPYRIGHT Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/15/200
22、7 21:40:32 MDTNo reproduction or networking permitted without license from IHS -,-,- 2 S 1039 : 2005 Classification Classification 1 m rack mainly used to storage business supplies Information : Terms are shown in Annex 1. Loading mass (loading mass per one shelf board) Bearable 40 kg 4 Classificati
23、on Classification 3 Classification 4 Classification 5 4.1 a) Shelves of shelf (book shelf) are mainly classified in classification 1 to classification 3, and the loading mass per one shelf board less than 100 kg. b) Shelves of racks are mainly classified in classification 4 to classification 12, and
24、 the loading mass per one shelf board is 100 kg and over to and including 500 kg. Classification by uses Classification by uses shall be as follows. The classification and the loading mass shall be as table 1. Bearable 80 kg Bearable 100 kg Bearable 150 kg Classification 8 Classification 9 Classific
25、ation 10 I Classification 2 I Bearable 60 kg I Bearable 300 kg Bearable 350 kg Bearable 400 kg I Classification 6 I Bearable 200 kg I I Classification 7 I Bearable 250 kg I I Classification 11 I Bearable 450 kg I I Classification 12 I Bearable 500 kg I 4.2 a) As for the connecting function in the wi
26、dth direction, there are independent type and connecting type. b) As for the number of shelf boards in the depth direction, there are single type and double type. As for the number of column supporting the shelf boards from side surface, there are single column type and double column type. Designati
27、on by structure shall be as table 2. Classification by structure Classification by structure shall be as follows: c PROTECTED BY COPYRIGHT Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/15/2007 21
28、:40:32 MDTNo reproduction or networking permitted without license from IHS -,-,- 3 S 1039 : 2005 Connecting function of opening width Independent type Table 2 Designation by structure Connecting type Number of column sup- porting the shelf boards Single coliiinn type Double column type Single coluni
29、ii type Double coliiinn type Number of shelf boards in the deuth direction 5 between the manufacturer and the purchaser. Dimensions The dimensions of shelf shall be in accordance with the agreement Information : Dimension marking of shelves is shown in Annex 2. 6 Quality 6.1 Appearance The appearanc
30、e shall be as follows: a) Finishing of appearances shall be good and there shall be no noticeable fault such as defects, warp, separation of connected parts and so on. Sharp intrusions, corners or fine split shall not exist at the parts where human body and clothes touch. The visible surface of pain
31、ted parts shall be uniform in luster, tone of colour paint- ing film, and free from defects such as uneven painting, sagging, and so on. b) c) 6.2 when tested according the specification in clause 9. Performance The performance shall comply with the specification of table 3 PROTECTED BY COPYRIGHT Co
32、pyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/15/2007 21:40:32 MDTNo reproduction or networking permitted without license from IHS -,-,- 4 S 1039 : 2005 Table 3 Performance grade 2 or over in table
33、 1 or grade 2 or over I I in table 2 of JIS H 8617 I Notes (1) (2) (3) Shelves fastened to wall and so on are deleted. Shall be applied to the height 1 800 mm or under. The invisible surface of painted parts shall be omitted. 7 a) b) C) d) e f) Structure The structure shall be as follows: Shelves sh
34、all be composed of columns, shelf boards, shelf board supporting equip- ment and accessories, and shall be able to be disassembled. Connecting parts shall be solid using welding, screw clamp and so on. To connect with screw or other metal fittings, the connecting part shall be the structure not easi
35、ly be loosened. Shelf boards shall be fixed by the method such that it does not easily slip out. The removable shelf board supporting equipments and so on shall be of a tightly fixed structure. The lowest shelf board may be fixed type. Shelves that do not independently support themselves shall be so
36、 structured to be connected to a solid structure (4) by the overturn preventive devices and so on. When applying wood or woody material, the structure shall be that which the de- PROTECTED BY COPYRIGHT Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employ
37、ees/1111111001, User=Wing, Bernie Not for Resale, 03/15/2007 21:40:32 MDTNo reproduction or networking permitted without license from IHS -,-,- 5 S 1039 : 2005 fects like breakage, divergence and so on after construction do not readily appear. Note (4) Solid structure means a building or a firmly co
38、nstructed body (includ- ing shelves). Information : Overturn preventing devices and so on shall be shown in Annex 3. 8 Materials Materials shall be as follows: a) Materials applied to the principal part shall have quality equivalent or superior to table 4. Table 4 Materials Classification of materia
39、ls Steel Wood Wooden materials Plywood Adhesive Coating Decorative laminate Materials JIS G 3101 JIS G 3131 JIS G 3141 JIS G 3350 JIS G 3445 JIS G 3466 Shall be in accordance with the lumbering and so on in JAS, whose moisture content be equal or less than 12 %, and shall be free from noticeable def
40、ects such as breakage, deforma- tion, worm-eaten spots and so on. Measuring of moisture content shall be in accordance with the method specified in JIS Z 2101 or electric measuring method. Shall be in accordance with the specification of JIS A 5905 and JIS A 5908, and the formaldehyde release shall
41、be equal or less than the specification of grade F *fib. Shall be in accordance with the plywood grade 1 or grade 2 in JAS, and the formaldehyde release shall be equal-or less than the specification of grade F *fib. Shall be in accordance with JIS A 5549 and JIS K 6804, and the formaldehyde release
42、shall be equal or less than the specification of grade F i? fib. Shall be in accordance with JIS K 5961 and JIS K 5962, and the formaldehyde release shall be equal or less than the ssecification of erade F $k-b-ik. JIS K 6903 b) Materials used shall be free from components detrimental to human healt
43、h. c) Materials of the accessories made of metal or synthetic resin shall have sufficient strength to bear the load of each of their functions and shall be materials with high in corrosion resistance or be treated well in corrosion resistance. 9 Tests 9.1 General test conditions The general test con
44、ditions shall be as follows: PROTECTED BY COPYRIGHT Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/15/2007 21:40:32 MDTNo reproduction or networking permitted without license from IHS -,-,- 6 S 10
45、39 : 2005 Temperature and humidity conditions at the test place The temperature and hu- midity conditions at the test place shall be ordinary temperature and ordinary hu- midity specified in JIS Z 8703. The test of shelf boards, however, shall be in accor- dance with 5.1 in JIS S 1200. Test specimen
46、 The test specimen shall be assembled according to instructions. If the shelves can be assembled or combined in different ways, the most adverse combination shall be used for each test. Tighten up any assembly fittings before testing. Classification of test The classification of the test indicates t
47、he different load ap- plied. The strength test as shown in 9.3 shall be performed in the same test classi- fica tion. Precision of test The precision of the test shall be, unless otheiwise specified, 5 % in force, 1 % in mass and 0.5 mm in precision of each part dimension. Testing equipment Floor su
48、rface Stopper The stopper shall be that to prevent the testing body from sliding but not tilting, not higher than 12 mm except in cases where the design of the test body necessitates the use of higher stopper, in these cases the lowest that will pre- vent the test body from moving shall be used. Loading pad The loading pad shall be rigid, cylinder, 100 mm in diameter, and having a flat face of 12 mm edge radius. Weight The weight shall be metal plates, metal bars or bags containing steel balls. lead balls and so on. i) 2) The testing floor surface sh