《JIS-Z-0239-2004-ENG.pdf》由会员分享，可在线阅读，更多相关《JIS-Z-0239-2004-ENG.pdf（24页珍藏版）》请在三一文库上搜索。
1、J IS JAPANESE I N DUSTR IAL STANDARD Translated and Published by Japanese Standards Association Kraft paper sacks- Method of specification ICs 55.080 Reference number : JIS Z 0239 : 2004 (E) PROTECTED BY COPYRIGHT 13 S Copyright Japanese Standards Association Provided by IHS under license with JSALi
2、censee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/15/2007 20:20:33 MDTNo reproduction or networking permitted without license from IHS -,-,- Z 0239 : 2004 Foreword This translation has been made based on the original Japanese Industrial Standard revised by the Minister of Economy
3、, Trade and Industry through deliberations at the Japanese Industrial Standards Committee, as the result of proposal for revision of Japanese Industrial Standard submitted by Japan Kraft Paper Sacks Industrial Association (JKPSA)/ Japanese Standards Association (JSA) with the draft being attached, b
4、ased on the provision of Article 12 Clause 1 of the Industrial Standardization Law applicable to the case of revision by the provision of Article 14. Consequently JIS Z 0239 : 1996 is replaced with this Standard. This revision has been made based on IS0 8351-1 : 1994 Packaging-Method of specificatio
5、n of sacks-Part 1 :Paper sacks for the purposes of making it easier to compare this Standard with International Standard; to prepare Japanese Industrial Standard conforming with International Standard; and to propose a draft of an International Standard which is based on Japanese Industrial Standard
6、. Attention is drawn to the possibility that some parts of this Standard may confiict with a patent right, application for a patent after opening to the public, utility model right or application for registration of utility model after opening to the public which have technical properties. The relev
7、ant Minister and the Japanese Industrial Standards Committee are not responsible for identifying the patent right, application for a patent after opening to the public, utility model right or application for registration of utility model after opening to the public which have the said technical prop
8、erties. Date of Establishment: 1996-10-20 Date of Revision: 2004-02-20 Date of Public Notice in Official Gazette: 2004-02-20 Investigated by: Japanese Industrial Standards Committee Standards Board Technical Committee on Logistics and Distribution of Goods JIS Z 0239 : 2004, First English edition pu
9、blished in 2004-09 Translated and published by: Japanese Standards Association 4-1-24, Akasaka, Minato-ku, Tokyo, 107-8440 JAPAN In the event of any doubts arising as to the contents, the original JIS is to be the final authority. O JSA 2004 All rights reserved. No part of this publication may be re
10、produced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. Printed in Japan PROTECTED BY COPYRIGHT Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Empl
11、oyees/1111111001, User=Wing, Bernie Not for Resale, 03/15/2007 20:20:33 MDTNo reproduction or networking permitted without license from IHS -,-,- Z 0239 : 2004 Contents Page Introduction . 1 2 3 3.1 3.2 Scope Normative references Method of specification . General Description Annex 1 (informative) A
12、method of manufacturing specification for each type of kraft paper sacks and the rule of inscription Annex 2 (informative) Comparison table between JIS and corresponding International Standard . 19 (i PROTECTED BY COPYRIGHT Copyright Japanese Standards Association Provided by IHS under license with
13、JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/15/2007 20:20:33 MDTNo reproduction or networking permitted without license from IHS -,-,- JAPANESE INDUSTRIAL STANDARD JIS Z 0239 : 2004 Kraft paper sacks-Method of specification Introduction This Japanese Industrial Standar
14、d has been prepared based on the first edition of IS0 8351-1 : 1994 Packaging-Method of specification for sacks-Part 1 : Paper sacks published in 1994 with some modifications of the technical contents. Portions given sidelines or dotted underlines are the matters modified from the original Internati
15、onal Standard. The list of modification with the explanation is given in annex 2 (informative) 1 Scope This Standard provides a checklist for the characteristics of kraft paper sacks (hereafter referred to as “paper sacks”) to be specified by the parties concerned when ordering. This Standard is pri
16、marily intended for application to the types of paper sacks specified in JIS Z 0102. Remarks : The International Standard corresponding to this Standard is as fol- lows. In addition, symbols which denote the degree of correspondence in the contents between the relevant International Standard and JIS
17、 are IDT (identical), MOD (modified), and NEQ (not equivalent) ac- cording to ISO/IEC Guide 21. IS0 8351-1 : 1994 Packaging-Method of specification for sacks- Part 1 : Paper sacks (MOD) 2 Normative references The following standards contain provisions which, through reference in this Standard, const
18、itute provisions of this Standard. If the indication of the year of publication is given to these referred standards, only the edition of the indicated year constitutes the provision of this Standard but the revision and amend- ment made thereafter do not apply. The normative references without the
19、indica- tion of the year of coming into effect apply only to the most recent edition (including amendments 1. JIS Z 0102 NOTE : IS0 6590-1 : 1983 Packaging-Sacks-Vocabulary and types-Part 1 : Paper sacks is equivalent to the said standard. Vocabulary for kraft paper sacks JIS Z 1531-1 NOTE : Kraft p
20、aper sacks-Description and method of measurement IS0 6591-1 : 1984 Packaging-Sacks-Description and method of mea- surement-Part l : Empty paper sacks is equivalent to the said standard. 3 Method of specification 3.1 General When drawing up the specifications of a paper sack for ordering pur- poses,
21、customer and manufacturer shall consider each item in the following lists and, where relevant, mutually agree to include them in the ordering Specifications at an appropriate level. PROTECTED BY COPYRIGHT Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Emp
22、loyees/1111111001, User=Wing, Bernie Not for Resale, 03/15/2007 20:20:33 MDTNo reproduction or networking permitted without license from IHS -,-,- 2 Z 0239 : 2004 The format of the ordering tomer and the manufacturer. specification shall be agreed upon between the cus- 3 . 2 Description 3 . 2 . 1 Th
23、e types of paper sacks are classified into open-mouth type and valved type, and the symbols of them corresponding to JIS Z 0102 are given below in parentheses. Sack type . 3 . 2 . 1 . 1 lowing: - sewn flat (C-1): Types of open-mouth sacks and symbol for them as given in the fol- - sewn gusseted (2-2
24、); - pasted flat hexagonal-bottom (A-1); - pasted gusseted rectangular-bottom (A-2); - pasted flat turn-over-bottom (A-3); - pasted gusseted turn-over-bottom (A-4); - pasted gusseted double-turn-over-bottom (A-5); . - pasted gusseted turn-over-bottom with reinforcing paper (A-5). 3 . 2 . 1 . 2 Types
25、 of valved sacks and symbol for them as given in the following: - sewn flat (D-1); - sewn gusseted (D-2); - pasted flat hexagonal-ends (B-1); - pasted gusseted rectangular-ends (B-1); - pasted gusseted turn-over-ends with reinforcing paper (B-2); . - longitudinal seam valved pasted gusseted turn-ove
26、r-ends (B-3); - longitudinal seam valved pasted gusseted double-turn-over-ends (B-4). . 3 . 2 . 2 Tube type - flush-cut; - stepped-end; - notched-end. 3 . 2 . 3 Dimensions accordance with JIS Z 1531-1. The following dimensions, in millimetres, shall be specified in - length of sack, a - width of sac
27、k (width of body), b - width of gusset, e - width of end (width of bottom), c . PROTECTED BY COPYRIGHT Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/15/2007 20:20:33 MDTNo reproduction or network
28、ing permitted without license from IHS -,-,- 3 2 0239 : 2004 - width of valve, g - length of valve, f - width of valve sleeve, u - length of valve sleeve, i - length of turn-over, p - sewing line distance, n, from adjacent sack transverse edge; - valve sleeve position, I: distance between outermost
29、edge of sack and outermost edge of valve sleeve, measured parallel to the bottom. 3.2.4 Type of material Each ply shall be specified by type, grammage (in grams per square metre) or thickness (in micrometres), surface treatment e.g. coating type and grammage, antislip type and application method, di
30、rection of the treatment faces (face in or face out). Thermoplastic film plies, normally an inner ply, shall be either type A or type B specified as follows: a) TypeA - loose or integral (degree of combination of film plies and the paper plies); - film type, e.g. PE-LD, PE-LLD, PE-HD, PVDC or ENAC;
31、- film state (flat or tubular); - film thickness, in micrometres; - film melt flow index, in grams per 10 min - length, in millimetres, where different from other plies (usually when loose or integral tubular); - gusset, in millimetres, where different from other plies (usually when loose or integra
32、l tubular); - width, in millimetres, where different from other plies (usually when loose or integral tubular); - heat seal distance, in millimetres, from adjacent sack or thermoplastic ply transverse edge; - skirt length, in millimetres, only for loose type; - Z-fold (type having 2-fold in the midd
33、le); - cuffed or uncuffed (with or without turn-over of film opening). b) TypeB - film type, e.g. PE-LD, PE-LLD, PE-HD, PVDC or ENAC; - film state (flat, tubular or bursiform); - film thickness, in micrometres; - film dimensions, in millimetres: winding width in the case of flat and tube width in th
34、e case of tube; . PROTECTED BY COPYRIGHT Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/15/2007 20:20:33 MDTNo reproduction or networking permitted without license from IHS -,-,- 4 Z 0239 : 2004 -
35、 dimensions of film sack: length and width, in millimetres, of sack; - specification of combination of film sacks: inserted, sewn, turned up on four sides or without turning up; - heat sealing position of bursiform film: distance, in millimetres, from the end part of sack bottom. 3.2.5 Perforations
36、- beneath valve: number, size and pattern; - ply: number, spacing, size and location of holes. 3.2.6 Valve/sleeve - valve type: simple, reinforced, internal sleeve, external sleeve, longitudinal . seam and heat sealable; . - valve position: i.e. in which corner of sack or at which longitudinal seam;
37、 - sleeve materials: e.g. kraft, polyethylene-coated kraft, tubular polyethylene. . 3.2.7 Longitudinal seam - type: continuous, interrupted or unbonded; - overlap width, in millimetres. 3.2.8 Pasted closure type - flush-cut bottom: witWwithout bottom patch and/or bottom cap: - stepped-end bottom: wi
38、tWwithout bottom patch and/or bottom cap: - stepped-end bottom: turn-over bottom; - flush cut or stepped-end turn-over or double turn-over bottom: witWwithout re- inforcing tape. . 3.2.9 Bottom patch - position: valved end, non-valved end; - material: type and grammage; - dimensions, in millimetres:
39、 length, width. 3.2.10 Bottom cap - position: valved end, non-valved end; - material: type and grammage; - dimensions, in millimetres: length, width; - wrap around: yesho. PROTECTED BY COPYRIGHT Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/111
40、1111001, User=Wing, Bernie Not for Resale, 03/15/2007 20:20:33 MDTNo reproduction or networking permitted without license from IHS -,-,- 5 2 0239 : 2004 3 . 2 . 1 1 Bottom orientation - folded towards sack face side; - folded towards sack back side. 3 . 2 . 1 2 Sewn closuredsewing 3 . 2 . 1 2 . 1 Ty
41、pe of sewn closure - simple; - taped and sewn (tape under sewing); - sewn and taped (tape over sewing); - taped and sewn and taped (reinforced); - heat-sealed and sewn and taped. 3 . 2 . 1 2 . 2 Type of stitch - single chain stitch: witldwithout filter cord; - double locked stitch: witldwithout filt
42、er cord. 3 . 2 . 1 2 . 3 Type of thread - natural; - synthetic; - blend. 3 . 2 . 1 2 . 4 Type of filter cord - jute (Filler cord); - paper (filler cord); - other. . 3 . 2 . 1 2 . 5 Stitch count per 250 mm or . . . . . . . . . . . . . . . . . . . . . 100 mm. 3 . 2 . 1 2 . 6 Tape protrusion from sack
43、edges, in millimetres. 3 . 2 . 1 2 . 7 Number of stitches in protruding tape. 3 . 2 . 1 2 . 8 Tape - type of tape: crepe tape, reinforcing tape and over tape; - material; - colour. 3 . 2 . 1 2 . 9 Sewing position: top or bottom of sack in relation to print. 3 . 2 . 1 3 Filling aperture (open-mouth s
44、acks only) PROTECTED BY COPYRIGHT Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/15/2007 20:20:33 MDTNo reproduction or networking permitted without license from IHS -,-,- 6 Z 0239 : 2004 - knife-
45、cut pattern: number of serrations per 100 mm and depth of serrations, in millimetres; - transverse pasting, (yesho): a all plies; b) discrete plies; c) longitudinal and horizontal position of paste spots. - thumb cut, yesho. 3.2.14 Adhesives - longitudinal seam pasting (body pasting): type, e.g. sta
46、rch, PVAC; - transverse pasting (inter-plies . paste feeding): type, e.g. PVAC, . hot melt, CMC; - bottom pasting: type, e.g. . PVAC, resin; - bottom patch and cap pasting: type, e.g. . . . . . . . . . . . . . . . . . . . . . PVAC; - special requirements, e.g. water-resistant, heat-stable, etc. 3.2.
47、15 Printing - ink type, e.g. oil- . or water-based acrylic, organic pigments; - ink colours, e.g. KI colour Nos, Pantone ref. Nos. - complete description of requirements and position of major elements of print, e.g. face side, back side, gussets, valve end, non-valve end. . . . . . . . . . . . . . .
48、 . . . . . . . . . . . . . . 3.2.16 Packaging shall be either type A or type ?3 specified as follows: . a). Type A - sacks in bundles: tiedhntiedfolded; - bundles in bales: total number of sacks per bale; - bundles in palletized units: total number of sacks per unit; - bundle stacking pattern; - shingled reels: diameter and overlap in millimetres, number of sacks; - pallet size and type, four-way entrykwo-way entry; - maximum unit height, in millimetres; - special requirements for automatic packers; - pallet wrapping: plastic, p