《SAE-AS-5002C-2007.pdf》由会员分享，可在线阅读，更多相关《SAE-AS-5002C-2007.pdf（3页珍藏版）》请在三一文库上搜索。
1、 AEROSPACE STANDARD FITTING, ELBOW, 90, BEAM SEAL AS5002 Copyright 2007 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, witho
2、ut the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1996-05 REAFFIRMED 2001-12 REVISED 2007-09 THIRD ANGLE PROJECTION CUS
3、TODIAN: SAE G-3/G-3B REV. C FEDERAL SUPPLY CLASS 4730 AS5002 SHEET 1 OF 3 REV. C PROCUREMENT SPECIFICATION: /5/ AS85421, AS85720 SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is en
4、tirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE inv
5、ites your written comments and suggestions. RATIONALE TO CORRECT THE DEFINED LEG DIAMETER DIM G. FIGURE 1 - FITTING, ELBOW, 90 TABLE 1 - DIMENSIONS AND WEIGHTS BASIC NO. AS5002 /15/ SIZE CODE (NOMINAL TUBE SIZE) T THREAD PER AS8879 CLASS A A G MIN V W LB/EA MAX CRES LB/EA MAX TI 03 04 05 06 08 10 12
6、 14 16 20 24 .188 .250 .312 .375 .500 .625 .750 .875 1.000 1.250 1.500 .3750-28 UNJS .4375-24 UNJS .5000-24 UNJS .5625-20 UNJS .7188-20 UNJS .8438-18 UNJS 1.0000-16 UNJ 1.1250-16 UNJ 1.2500-14 UNJS 1.5781-14 UNJS 1.8438-14 UNJS .575 .617 .653 .704 .824 .955 1.062 1.216 1.246 1.387 1.688 .285 .329 .3
7、91 .454 .547 .673 .860 1.110 1.110 1.360 1.610 .360- .377 .360- .377 .423- .440 .485- .502 .547- .565 .673- .691 .860- .878 1.110-1.128 1.110-1.128 1.355-1.380 1.605-1.630 .055 .060 .060 .060 .065 .070 .095 .105 .115 .110 .130 .0305 .0341 .0456 .0571 .0782 .119 .192 .372 .335 .496 .824 .0174 .0195 .
8、0261 .0326 .0447 .0680 .110 .213 .191 .283 .471 Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 20:20:51 MSTNo reproduction or networking permitted without license from IHS -,-,- AEROSPACE STANDARD FITTING, ELBOW, 90
9、, BEAM SEAL AS5002 SHEET 2 OF 3 REV. C NOTES: /1/ MATERIAL: a. CODE LETTER T - TYPE 6AL-4V TITANIUM ALLOY FORGING OR BAR PER AMS 4965. b. CODE LETTER P - TYPE 17-4PH CORROSION RESISTANT STEEL FORGING OR BAR PER AMS 5643. c. CODE LETTER V - TYPE 15-5PH CORROSION RESISTANT STEEL FORGING OR BAR PER AMS
10、 5659. 2. HEAT TREATMENT: a. MATERIAL CODE LETTER T - NONE. b. MATERIAL CODE LETTERS P AND V - HEAT TREAT TO CONDITION H 1075 PER AMS 2759/3. 3. FINISH: a. MATERIAL CODE LETTER T - NONE. b. MATERIAL CODE LETTERS P AND V - PASSIVATE PER AMS 2700. /4/ DRY FILM LUBRICANT: APPLY DRY FILM LUBRICANT PER A
11、S5272, TYPE I TO SEALING SURFACE. OVERSPRAY IN BORE IS NOT PERMITTED. /5/ PROCUREMENT SPECIFICATION: AS85421 FOR OPERATING PRESSURES TO 4000 psi AND AS85720 FOR OPERATING PRESSURES TO 5000 psi, EXCEPT AS SPECIFIED ON THIS STANDARD. THIS PART SHALL BE QUALIFIED TO THE PROCUREMENT SPECIFICATION AS APP
12、LICABLE IN A COMPLETE ASSEMBLY. USERS OF THIS STANDARD ARE ADVISED TO CONTROL SOURCE APPROVAL(S) BY STANDARD PAGE SUPPLEMENT SHEET OR SIMILAR MEANS. /6/ IDENTIFICATION AT LOCATION SHOWN: MARK PER AS478 CLASS C OR D OR METHOD 7A3, 15A3, OR 15B. /7/ a. FOR SIZES 06 (.375 OD TUBE SIZE) AND SMALLER: MAN
13、UFACTURERS NAME OR TRADEMARK, MATERIAL CODE LETTER, AND MAXIMUM PRESSURE RATING. (EXAMPLE: 5K = 5000 psi.) b. FOR SIZES 08 (.500 OD TUBE SIZE) AND LARGER: MANUFACTURERS NAME OR TRADEMARK, BASIC PART NUMBER, MATERIAL CODE LETTER, AND MAXIMUM PRESSURE RATING. (EXAMPLE: 5K = 5000 psi.) /7/ THIS PART IS
14、 DESIGNED FOR USE IN SYSTEMS WITH MAXIMUM OPERATING PRESSURES AS FOLLOWS: a. SIZES 03 THROUGH 16 AT 5000 psi b. SIZE 20 AT 3000 psi c. SIZE 24 AT 2000 psi 8. WHEN MACHINED FROM BAR OR OVERSIZED FORGINGS, THE CENTER BODY SECTION SHALL CONFORM TO AS1376, TABLE 4. /9/ .030 TO .125 RADIUS UNLESS QUALIFI
15、CATION OF SPECIAL PROCESS WITH SMALLER RADIUS. APPLICABLE FOR TITANIUM ALLOY PARTS ONLY. 10. INTERPRETATION OF DRAWING PER ARP4296. Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 20:20:51 MSTNo reproduction or netwo
16、rking permitted without license from IHS -,-,- AEROSPACE STANDARD FITTING, ELBOW, 90, BEAM SEAL AS5002 SHEET 3 OF 3 REV. C 11. SURFACE TEXTURE: SYMBOLS PER ANSI Y14.36; REQUIREMENTS PER ANSI/ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 in Ra. FORGED SURFACES MAY BE 250 in Ra.
17、12. REMOVE ALL BURRS AND BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 13. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994 14. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .015, ANGULAR DIMENSIONS 2. /15/ EXAMPLE OF PART NUMBER: 16. THE CHANGE BAR ( l ) LOCAT
18、ED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT. Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 20:20:51 MSTNo reproduction or networking permitted without license from IHS -,-,-