《SAE-AS-4882A-2003-R2007.pdf》由会员分享，可在线阅读，更多相关《SAE-AS-4882A-2003-R2007.pdf（4页珍藏版）》请在三一文库上搜索。
1、SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefr
2、om, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. SHEET 1 OF 4 AS4882 REV. A THIRD ANGLE PROJECTION AEROSPACE STANDARD AS4882 REV. A IS
3、SUED 1996-12 REVISED 2003-09 REAFFIRMED 2007-07 CLAMP, LOOP, CUSHIONED, HINGED, QUICK RELEASE - CABLE OR WIRE CUSTODIAN: SAE G-3/G-3EPROCUREMENT SPECIFICATION: NONE FEDERAL SUPPLY CLASS 5340 FIGURE 1 - QUARTER TURN QUICK RELEASE CLAMP RATIONALE THIS DOCUMENT HAS BEEN REAFFIRMED TO COMPLY WITH THE SA
4、E 5-YEAR REVIEW POLICY. Copyright 2007 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission o
5、f SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not
6、for Resale, 12/04/2007 18:58:20 MSTNo reproduction or networking permitted without license from IHS -,-,- CLAMP, LOOP, CUSHIONED, HINGED, QUICK RELEASE - CABLE OR WIRE AEROSPACE STANDARD AS4882 SHEET 2 OF 4 AS4882 REV. A REV. A FIGURE 2 - VIEW J-J ENLARGED SHOWING QUARTER TURN LOCKING DEVICE IN UNLO
7、CKED POSITION CUSHION OMITTED FOR CLARITY FIGURE 3 - VIEW L-L SHOWING SLOT IN BRACKET Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 18:58:20 MSTNo reproduction or networking permitted without license from IHS -,-,-
8、 CLAMP, LOOP, CUSHIONED, HINGED, QUICK RELEASE - CABLE OR WIRE AEROSPACE STANDARD AS4882 SHEET 3 OF 4 AS4882 REV. A REV. A FIGURE 4 - DEVELOPED FLAT PATTERN SHOWING LAY OF CUSHION FIGURE 5 - SECTION K-K ENLARGED CUSHION ONLY REMOVE ALL FLASH TABLE 1 - DIMENSIONS BASIC NO. AS4882 SIZE CODE /13/ WORKI
9、NG DIAMETER RANGE D .015 E .030F G .03H 01 .35- .42 .825.5611.18 .881.84 02 .42- .49 .885.6011.26 .911.89 03 .49- .57 .955.6321.34 .941.95 04 .57- .681.055.6631.38 .992.03 05 .68- .801.175.7261.501.062.15 06 .80- .931.305.7871.651.132.26 07 .93-1.071.445.8501.771.202.38 081.07-1.211.585.8781.891.272
10、.51 Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 18:58:20 MSTNo reproduction or networking permitted without license from IHS -,-,- CLAMP, LOOP, CUSHIONED, HINGED, QUICK RELEASE - CABLE OR WIRE AEROSPACE STANDARD
11、AS4882 SHEET 4 OF 4 AS4882 REV. A REV. A NOTES: 1.MATERIAL: BAND AND MOUNTING BRACKET: TYPE .321 CORROSION RESISTANT STEEL PER AMS 5510 CUSHION: FIBERGLASS FABRIC REINFORCED SILICONE PER AMS 3352 FASTENER: STYLE LETTER A: THUMBSCREW PER ASME B18.17, TYPE A, REGULAR, THREAD SIZE .1900-32; 300 SERIES
12、CORROSION RESISTANT STEEL PER AMS-STD-66. STYLE LETTER B: .190-32UNJF-3A TWELVE-POINT BOLT A286 CORROSION RESISTANT STEEL PER MS9556-06. WASHER: TYPE 321 CORROSION RESISTANT STEEL PER AMS 5510. SPRING: 300 SERIES CORROSION RESISTANT STEEL PER ASTM A 313. NUT: TYPE 303 CORROSION RESISTANT STEEL PER A
13、MS 5640. /2/IDENTIFICATION: MARK PART NUMBER AND MANUFACTURERS NAME, TRADEMARK OR CAGE CODE PER AS478- 2A1. 3.MAXIMUM CONTINUOUS TEMPERATURE: 540 F. 4.NUT SHALL BE DEFORMED TO PROVIDE TORQUE REQUIREMENTS PER NASM25057 AND SHALL BE PRESENT ON BOLT FOR QUARTER TURN RELEASE IN ASSEMBLED CONDITION, NUT
14、MUST PASS THROUGH SLOT IN LOWER CLAMP HALF AND MOUNTING BRACKET AND SEAT ON DIMPLES. /5/BOLT THREADS SHALL PROTRUDE THROUGH END OF NUT 1.5 THREADS MINIMUM. /6/CUSHION SHALL BE THE ONLY PORTION OF CLAMP ASSEMBLY TO MAKE CONTACT WITH CABLE OR WIRE BUNDLES AND WHEN ASSEMBLED, THE LENGTH SHALL BE LONG E
15、NOUGH TO ENSURE TOTAL CLAMPING. THIS CAN BE VERIFIED BY INSTALLING THE CLAMP ON ANY CYLINDRICAL SHAPE WITH A DIAMETER EQUAL TO THE WORKING DIAMETER RANGE DESIRED AND LOCKING THE CLAMP WITH A QUARTER TURN AS DESCRIBED IN NOTE 4. /7/ID OF CUSHION MUST FIT NOMINAL OD OF CABLE WITHIN .06 AND BE CAPABLE
16、OF HAVING 6 LB MINIMUM AXIAL FORCE APPLIED AND NOT SLIP ON CABLE AT ASSEMBLY. /8/TIPS OF CUSHION RIBS MAY BE FLAT OR RADIUSED. 9.BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 10.DIMENSIONING AND TOLERANCING: ANSI Y14.5M-1982 (ASME PUBLICATION). 11.DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIF
17、IED, TOLERANCES: LINEAR DIMENSIONS .010, ANGULAR DIMENSIONS 5. /12/EXAMPLE OF PART NUMBER: 13.THE CHANGE BAR ( l ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT.
18、AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT. AS AND AMS ARE SOCIETY OF AUTOMOTIVE ENGINEERS, INC. PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. ASTM IS AN AMERICAN SOCIETY FOR TESTING AND MATERIALS PUBLICATION. Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 18:58:20 MSTNo reproduction or networking permitted without license from IHS -,-,-