《SAE-AS-5164A-2003-R2007.pdf》由会员分享，可在线阅读，更多相关《SAE-AS-5164A-2003-R2007.pdf（3页珍藏版）》请在三一文库上搜索。
1、SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefr
2、om, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. SHEET 1 OF 3 AS5164 REV. A THIRD ANGLE PROJECTION AEROSPACE STANDARD AS5164 REV. A IS
3、SUED 2000-07 REVISED 2003-08 REAFFIRMED 2007-07 FITTING, CONNECTOR, MULTIPLE FLUID PRESSURE LINE, 45 CUSTODIAN: SAE G-3/G-3BPROCUREMENT SPECIFICATION: /4/ AS4875/1 FEDERAL SUPPLY CLASS 4730 FIGURE 1 - FITTING, CONNECTOR, 45 RATIONALE THIS DOCUMENT HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE 5-YEAR RE
4、VIEW POLICY. Copyright 2007 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO P
5、LACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale,
6、 12/04/2007 20:11:37 MSTNo reproduction or networking permitted without license from IHS -,-,- FITTING, CONNECTOR, MULTIPLE FLUID PRESSURE LINE, 45 AEROSPACE STANDARD AS5164 SHEET 2 OF 3 AS5164 REV. A REV. A NOTES: /1/MATERIAL: a.DASH AS CODE LETTER - TYPE 4130 CARBON STEEL FORGING OR BAR PER AMS-S-
7、6758 OR AMS 6370; OR TYPE 4140 PER AMS 6382. /2/ b.CODE LETTER D - TYPE 2014-T6 ALUMINUM ALLOY FORGING PER AMS 4133; OR TYPE 2024-T6 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/6 OR TYPE 2024-T851 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/6 OR AMS 4339. /2/ c.CODE LETTER J - TYPE 304 CORROSION RESISTANT STEEL FOR
8、GING OR BAR PER AMS-QQ-S-763 OR AMS 5639. d.CODE LETTER K - TYPE 316 CORROSION RESISTANT STEEL FORGING OR BAR PER AMS-QQ-S-763 OR AMS 5648. e.CODE LETTER R - TYPE 321 CORROSION RESISTANT STEEL FORGING OR BAR PER AMS-QQ-S-763 OR AMS 5645. f.CODE LETTER T - TYPE 6AL-4V TITANIUM ALLOY FORGING OR BAR PE
9、R AMS 4928. g.CODE LETTER W - TYPE 7075-T73 ALUMINUM ALLOY FORGING PER AMS 4141; OR TYPE 7075-T73 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/9; OR TYPE 7075-T7351 ALUMINUM ALLOY BAR PER AMS 4124. /2/ /2/HEAT TREATMENT: a.DASH AS CODE LETTER - SEE HARDNESS REQUIREMENT PER PROCUREMENT SPECIFICATION. b.CODE L
10、ETTERS D AND W - SEE ELECTRICAL CONDUCTIVITY AND HARDNESS REQUIREMENT PER PROCUREMENT SPECIFICATION. c.OTHER CODE LETTERS - NONE. TABLE 1A - DIMENSIONS BASIC NO. AS5164 /13/ SIZE CODE (NOMINAL TUBE SIZE) T THREAD PER AS8879 CLASS 3A A .023 C .005 D .005E F .001 04 .250 .4375-20 UNJF1.023 .692 .474 .
11、562 .439 05 .312 .5000-20 UNJF1.023 .755 .536 .625 .501 06 .375 .5625-18 UNJF1.085 .817 .599 .750 .564 08 .500 .7500-16 UNJF1.3351.005 .786 .937 .751 10 .625 .8750-14 UNJF1.4911.130 .9111.125 .876 12 .7501.0625-12 UNJ1.6481.3181.0991.3751.063 161.0001.3125-12 UNJ1.8661.5681.3491.6871.313 TABLE 1B -
12、DIMENSIONS AND WEIGHTS BASIC NO. AS5164 /13/ SIZE CODEG H .010KV LB/EA APPROX. REF AL LB/EA APPROX. REF STEEL LB/EA APPROX. REF TI 04.437 .750 .375 .797- .815 .0268 .0770 .0425 05.437 .750 .500 .797- .815 .0221 .0633 .0349 06.500 .875 .500 .985-1.003 .0387 .111 .0614 08.5001.125 .7501.173-1.191 .062
13、7 .180 .0994 10.6251.375 .8121.355-1.380 .0989 .284 .157 12.6251.6251.0001.668-1.693 .163 .469 .259 16.8122.1251.5002.042-2.072 .269 .772 .426 Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 20:11:37 MSTNo reproducti
14、on or networking permitted without license from IHS -,-,- FITTING, CONNECTOR, MULTIPLE FLUID PRESSURE LINE, 45 AEROSPACE STANDARD AS5164 SHEET 3 OF 3 AS5164 REV. A REV. A 3.FINISH: a.DASH AS CODE LETTER - CADMIUM PLATE PER QQ-P-416, TYPE II, CLASS 2, DYE BLACK AND COAT WITH A LIGHT FILM OF OIL PER P
15、ROCUREMENT SPECIFICATION. b.CODE LETTER D - ANODIZE PER AMS 2472 OR MIL-A-8625, TYPE II, CLASS 2, DYE BLUE, DUPLEX SEAL PER PROCUREMENT SPECIFICATION. c.CODE LETTERS J, K, AND R - PASSIVATE PER AMS-QQ-P-35, TYPE VI OR VII. d.CODE LETTER T - ANODIZE PER AMS 2488 OR FLUORIDE PHOSPHATE CONVERSION COAT
16、PER AMS 2486 WITH COLOR PER PROCUREMENT SPECIFICATION. e.CODE LETTER W - ANODIZE PER MIL-A-8625, TYPE II, CLASS 2, DYE BROWN, DUPLEX SEAL PER PROCUREMENT SPECIFICATION. /4/PROCUREMENT SPECIFICATION: AS4875/1 EXCEPT AS SPECIFIED ON THIS STANDARD. USERS OF THIS STANDARD SHALL PROCURE THIS PRODUCT FROM
17、 ACCREDITED MANUFACTURER(S) OR ACCREDITED DISTRIBUTOR(S) AS LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED MANUFACTURERS LIST (QML) FOR THIS TYPE PRODUCT. /5/IDENTIFICATION AT LOCATION SHOWN: MARK PER AS478 CLASS C OR D OR METHOD 7A3, 15A3, OR 15B. a.FOR SIZE 06 AND SMALLER: MANUFACTURER
18、S NAME, CAGE CODE OR TRADEMARK, LETTERS “AS” AND MATERIAL CODE LETTER. b.FOR SIZE 08 AND LARGER: MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, BASIC PART NUMBER AND MATERIAL CODE LETTER. 6.INTENDED USE: THIS PART IS DESIGNED FOR USE IN SYSTEMS WITH MAXIMUM OPERATING PRESSURES AS FOLLOWS: a.SIZES 04 TH
19、ROUGH 12 IN ALUMINUM ALLOY AND SIZES 04 THROUGH 16 IN CORROSION RESISTANT STEEL AND TITANIUM ALLOY AT 3000 psi. b.SIZE 16 IN ALUMINUM ALLOY AT 1500 psi. THIS STANDARD IS THE FUNCTIONAL EQUIVALENT OF AN778 AND IS INTENDED TO BE SUITABLE AS A REPLACEMENT STANDARD. 7.WHEN MACHINED FROM BAR OR OVERSIZED
20、 FORGINGS, THE CENTER BODY SECTION SHALL CONFORM TO AS1376, TABLE 8. 8.INTERPRETATION OF DRAWING PER ARP4296. 9.SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M; REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 in Ra. FORGED SURFACES MAY BE 250 in Ra. 10.BREAK EDGES .003
21、 TO .015 UNLESS OTHERWISE SPECIFIED. 11.DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994. 12.DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .016, ANGULAR DIMENSIONS 030. /13/EXAMPLE OF PART NUMBER: 14.THE CHANGE BAR ( l ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIEN
22、CE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT. Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 20:11:37 MSTNo reproduction or networking permitted without license from IHS -,-,-