《TIA-SP-3-3834-RV3-2005.pdf》由会员分享,可在线阅读,更多相关《TIA-SP-3-3834-RV3-2005.pdf(40页珍藏版)》请在三一文库上搜索。
1、 2500 Wilson Boulevard Suite 300 Arlington, VA 22201-3834 USA +1.703.907.7700 FAX +1.703.907.7727 The Telecommunications Industry Association represents the communications sector of February 10, 2005 SUBJECT: Standards Proposal No. 3-3834-RV3, proposed revision of an existing TIA Standard TIA/EIA-45
2、5-B, “Standard test procedure for fiber optic fibers, cables, transducers, sensors, connecting and terminating devices, and other fiber optic components” (if approved, to be published as TIA-455-C) BACKGROUND: The attached material was prepared by TIA FO-4.5 Subcommittee on Fiber Optic Metrology and
3、 was approved by the chair of the formulating group. SP-3-3834-RV3 is herewith submitted to TIA membership and others as a step toward standardization. NOTE: Please use the following format for comments: Company Name - Comment No. Type of Comment - Technical or Editorial Reference - Page No., Clause
4、 No., Line Suggested Change - Change From:. To:. Add:, Delete: Rationale for Technical Change COMMENT PERIOD EXPIRES: MARCH 7, 2005 Prior to this date, comments may be submitted for consideration as noted on page two of this form. Following the expiration of the comment period, and consideration by
5、the relevant committee, this Proposal will be submitted to the TIA Technical Standards Subcommittee (TSSC) for final approval as to acceptance or rejection of this Standards Proposal. B U I L D I N G G L O B A L C O M M U N I C A T I O N S Copyright Telecommunications Industry Association Provided b
6、y IHS under license with EIALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/29/2007 21:07:17 MDTNo reproduction or networking permitted without license from IHS -,-,- PLEASE FILL OUT AND SIGN THIS FORM AND RETURN IT WITH ANY COMMENTS TO: TIA Standards Secretariat Telecommunic
7、ations Industry Assoc. 2500 Wilson Blvd., Suite 300 Arlington, VA 22201-3834 (FAX: 703/907-7727) SUBJECT: Standards Proposal No. 3-3834-RV3, proposed revision of an existing TIA Standard TIA/EIA-455-B, “Standard test procedure for fiber optic fibers, cables, transducers, sensors, connecting and term
8、inating devices, and other fiber optic components” (if approved, to be published as TIA- 455-C) COMMENT PERIOD EXPIRES: MARCH 7, 2005 USER PRODUCER USER/PRODUCER GENERAL INTEREST Please circle one only to indicate the most accurate description of the relevance of this Standards Proposal to your comp
9、any. This information is required by ANSI to process your comments. DATE:_ NAME:_ Please Print TEL:_ NAME:_ Signature E-MAIL_ COMPANY:_ _ ADDRESS:_ _ -page 2- Copyright Telecommunications Industry Association Provided by IHS under license with EIALicensee=IHS Employees/1111111001, User=Wing, Bernie
10、Not for Resale, 03/29/2007 21:07:17 MDTNo reproduction or networking permitted without license from IHS -,-,- NOTICE This document is a TIA Engineering Standards Proposal, rather than an interim or final Standard. It is published for purposes of comment and is subject to further review and modificat
11、ion by the TIA Technical Standards Subcommittee (TSSC), which may accept or reject the Standards Proposal. Accordingly, readers of this Standards Proposal are cautioned against relying on information contained therein prior to the adoption of a final standard. TIA disclaims any liability or responsi
12、bility for the consequences of such reliance. Published by TELECOMMUNICATIONS INDUSTRY ASSOCIATION 2004 2500 Wilson Boulevard Arlington, VA 22201 All rights reserved Printed in U.S.A. PRICE: $67.00 Copyright Telecommunications Industry Association Provided by IHS under license with EIALicensee=IHS E
13、mployees/1111111001, User=Wing, Bernie Not for Resale, 03/29/2007 21:07:17 MDTNo reproduction or networking permitted without license from IHS -,-,- NOTICE OF DISCLAIMER AND LIMITATION OF LIABILITY The document to which this Notice is affixed (the “Document”) has been prepared by one or more Enginee
14、ring Committees or Formulating Groups of the Telecommunications Industry Association (“TIA”). TIA is not the author of the Document contents, but publishes and claims copyright to the Document pursuant to licenses and permission granted by the authors of the contents. TIA Engineering Committees and
15、Formulating Groups are expected to conduct their affairs in accordance with the TIA Engineering Manual (“Manual”), the current and predecessor versions of which are available at http:/www.tiaonline.org/standards/sfg/engineering_manual.cfm. TIAs function is to administer the process, but not the cont
16、ent, of document preparation in accordance with the Manual and, when appropriate, the policies and procedures of the American National Standards Institute (“ANSI”). TIA does not evaluate, test, verify or investigate the information, accuracy, soundness, or credibility of the contents of the Document
17、. In publishing the Document, TIA disclaims any undertaking to perform any duty owed to or for anyone. If the Document is identified or marked as a project number (PN) document, or as a standards proposal (SP) document, persons or parties reading or in any way interested in the Document are cautione
18、d that: (a) the Document is a proposal; (b) there is no assurance that the Document will be approved by any Committee of TIA or any other body in its present or any other form; (c) the Document may be amended, modified or changed in the standards development or any editing process. The use or practi
19、ce of contents of this Document may involve the use of intellectual property rights (“IPR”), including pending or issued patents, or copyrights, owned by one or more parties. TIA makes no search or investigation for IPR. When IPR consisting of patents and published pending patent applications are cl
20、aimed and called to TIAs attention, a statement from the holder thereof is requested, all in accordance with the Manual. TIA takes no position with reference to, and disclaims any obligation to investigate or inquire into, the scope or validity of any claims of IPR. TIA will neither be a party to di
21、scussions of any licensing terms or conditions, which are instead left to the parties involved, nor will TIA opine or judge whether proposed licensing terms or conditions are reasonable or non-discriminatory. TIA does not warrant or represent that procedures or practices suggested or provided in the
22、 Manual have been complied with as respects the Document or its contents. TIA does not enforce or monitor compliance with the contents of the Document. TIA does not certify, inspect, test or otherwise investigate products, designs or services or any claims of compliance with the contents of the Docu
23、ment. ALL WARRANTIES, EXPRESS OR IMPLIED, ARE DISCLAIMED, INCLUDING WITHOUT LIMITATION, ANY AND ALL WARRANTIES CONCERNING THE ACCURACY OF THE CONTENTS, ITS FITNESS OR APPROPRIATENESS FOR A PARTICULAR PURPOSE OR USE, ITS MERCHANTABILITY AND ITS NON- INFRINGEMENT OF ANY THIRD PARTYS INTELLECTUAL PROPE
24、RTY RIGHTS. TIA EXPRESSLY DISCLAIMS ANY AND ALL RESPONSIBILITIES FOR THE ACCURACY OF THE CONTENTS AND MAKES NO REPRESENTATIONS OR WARRANTIES REGARDING THE CONTENTS COMPLIANCE WITH ANY APPLICABLE STATUTE, RULE OR REGULATION, OR THE SAFETY OR HEALTH EFFECTS OF THE CONTENTS OR ANY PRODUCT OR SERVICE RE
25、FERRED TO IN THE DOCUMENT OR PRODUCED OR RENDERED TO COMPLY WITH THE CONTENTS. TIA SHALL NOT BE LIABLE FOR ANY AND ALL DAMAGES, DIRECT OR INDIRECT, ARISING FROM OR RELATING TO ANY USE OF THE CONTENTS CONTAINED HEREIN, INCLUDING WITHOUT LIMITATION ANY AND ALL INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUE
26、NTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF BUSINESS, LOSS OF PROFITS, LITIGATION, OR THE LIKE), WHETHER BASED UPON BREACH OF CONTRACT, BREACH OF WARRANTY, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE FOREGOING NEGATION OF DAMA
27、GES IS A FUNDAMENTAL ELEMENT OF THE USE OF THE CONTENTS HEREOF, AND THESE CONTENTS WOULD NOT BE PUBLISHED BY TIA WITHOUT SUCH LIMITATIONS. Copyright Telecommunications Industry Association Provided by IHS under license with EIALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/2
28、9/2007 21:07:17 MDTNo reproduction or networking permitted without license from IHS -,-,- SP-3-3834-RV3, 24-Jan-2005 To be TIA/EIA-455-C TIA/EIA-455-C Standard test procedure for fiber optic fibers, cables, transducers, sensors, connecting and terminating devices, and other fiber optic components Co
29、ntents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2. Normative references . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 3. Numbering system . . . . . . . . . . . . . . . . . . . . . .
30、. . . . . . . . . . . . . . . . . . . . . . .3 4. Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 5. Definitions and symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 6. Standard atmospheric c
31、onditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 7. Metric policy for FOTPs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 8. Format for addenda (FOTPs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 9. In
32、ternational standards and harmonization . . . . . . . . . . . . . . . . . . . . . . . . . 10 10. Annexes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Annex A - Glossary of terms applicable to this standard and its addenda . . . . 11 Annex B
33、 - Methods for establishing empirical equivalence . . . . . . . . . . . . . . . .15 Annex C - Comparison between this standard and IEC or ITU requirements . .27 Annex D Corrections for vacuum wavelength . . . . . . . . . . . . . . . . . . . . . . . . 27 D R A F T Copyright Telecommunications Industr
34、y Association Provided by IHS under license with EIALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/29/2007 21:07:17 MDTNo reproduction or networking permitted without license from IHS -,-,- SP-3-3834-RV3, 24-Jan-2005 To be TIA/EIA-455-C ii This page left blank. D R A F T Cop
35、yright Telecommunications Industry Association Provided by IHS under license with EIALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/29/2007 21:07:17 MDTNo reproduction or networking permitted without license from IHS -,-,- SP-3-3834-RV3, 24-Jan-2005 To be TIA/EIA-455-C iii T
36、IA/EIA-455-C Standard test procedure for fiber optic fibers, cables, transducers, sensors, connecting and terminating devices, and other fiber optic components Foreword (This foreword is informative and is not part of this standard.) This document comes from TIA Project No. 3834, and was formulated
37、under the cognizance of TIA FO-6.6 Subcommittee on Optical Fibers and Cables, and TIA FO-6.6.4, Working Group on Measurement Protocols. This document serves as the “umbrella“ for a series of addenda, and is common to all test procedures included within Recommended Standard TIA/EIA-455. There are fou
38、r annexes: two are normative and two are informative. Key words: fiber optic tests procedures (FOTPs), atmospheric conditions, metric policy, format, equivalence NOTE - This document was originally published as Recommended Standard TIA/EIA-455. TIA/EIA-455-B is a revision to TIA/EIA-455-A. D R A F T
39、 Copyright Telecommunications Industry Association Provided by IHS under license with EIALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/29/2007 21:07:17 MDTNo reproduction or networking permitted without license from IHS -,-,- SP-3-3834-RV3, 24-Jan-2005 To be TIA/EIA-455-C i
40、v This page left blank. D R A F T Copyright Telecommunications Industry Association Provided by IHS under license with EIALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/29/2007 21:07:17 MDTNo reproduction or networking permitted without license from IHS -,-,- SP-3-3834-RV3,
41、24-Jan-2005 To be TIA/EIA-455-C 1 Standard test procedure for fiber optic fibers, cables, transducers, sensors, connecting and terminating devices, and other fiber optic components 1 Introduction This document, together with its addenda, provides uniform test procedures for testing fiber optic compo
42、nents intended for, or forming a part of, optical communications and data transmission systems. Neither this document, nor its addenda, provide procedures designed for testing fiber optic systems. For test procedures for fiber optic systems or subsystems, refer to the TIA/EIA-526 series of documents
43、. The test procedures included in the addenda to this document are designed to satisfy the broadest possible industry requirements; in general, special test methods are not included. In order to adequately cover these broad industry needs, many of the addenda require that some “option designator,“ s
44、ome test parameter definition, and/or some pass/fail criteria to be specified whenever the addendum is called out. Only in special cases (such as specified DoD requirements) are special test details listed in the addendum in addition to the general requirements. Specific test requirements (including
45、 DoD requirements) can, of course, be modified by direction of the Detail Specification so that the particular test can accurately reflect the special test needs (more or less severe than standard) of the component in question. In the event of conflict between the provisions of these test procedures
46、 and those of the Detail Specification, the requirements of the Detail Specification shall govern. In the terminology of IEC Guide 102 and of EIA EP-11, this document, together with its addenda, is considered to be a Basic Specification. 2 Normative references The following publications contain prov
47、isions which, through reference in this text, may constitute provisions of this Standard. At the time of publication, the editions indicated were valid. All publications are subject to revision, and parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the publications indicated below. D R A F T Copyright Telecommuni