《UL-1414-BULLETINS-2007.pdf》由会员分享，可在线阅读，更多相关《UL-1414-BULLETINS-2007.pdf（66页珍藏版）》请在三一文库上搜索。
1、FOR INTERNAL UL OR CSDS USE ONLY NOT FOR OUTSIDE DISTRIBUTION Subject 1414 August 31, 2007 SUMMARY OF TOPICS The following is being proposed: 1. The First Edition of the Standard for Fixed Capacitors for Use in Electronic Equipment Part 14: Sectional specifi cation: Fixed capacitors for electromagne
2、tic interference suppression and connection to the supply mains, UL 60384-14 STP BALLOTS AND ALL COMMENTS DUE: October 15, 2007 1. The First Edition of the Standard for Fixed Capacitors for Use in Electronic Equipment Part 14: Sectional specifi cation: Fixed capacitors for electromagnetic interferen
3、ce suppression and connection to the supply mains, UL 60384-14 RATIONALE Proposal submitted by: Harmonization Committee for UL 1414/ IEC 60384-14 Based on feedback from UL 1414 industry members and end-product manufacturers, a Committee was formed to harmonize UL 1414, the Standard for Capacitors an
4、d Suppressors for Radio- and Television-Type Appliances, with IEC 60384-14, Fixed Capacitors for Use in Electronic Equipment - Part 14: Sectional Specifi cation: Fixed Capacitors for Electromagnetic Interference Suppression and Connection to the Supply Mains. Existing requirements in UL 1414 were co
5、mpared to the requirements of IEC 60384-14 to determine whether or not a national difference would be needed for the new UL standard. A few national differences were identifi ed. Therefore, the following is a proposal to adopt IEC 60384-14 as a UL Standard, UL 60384-14, including national difference
6、s. All national differences included in this proposed new standard are formatted as bold and indented. They are also numbered with a “DV.” Copyright Underwriters Laboratories Inc. Provided by IHS under license with ULLicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 09/03/2007 00:
7、50:04 MDTNo reproduction or networking permitted without license from IHS -,-,- FOR INTERNAL UL OR CSDS USE ONLY NOT FOR OUTSIDE DISTRIBUTION FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT Part 14: Sectional specifi cation: Fixed capacitors for electromagnetic interference suppression and connecti
8、on to the supply mains 1 General 1.1 Scope This part of IEC 60384 applies to capacitors and resistor-capacitor combinations which will be connected to an a.c. mains or other supply with nominal voltage not exceeding 1 000 V a.c. (r.m.s.) or 1 000 V d.c. and with a nominal frequency not exceeding 100
9、 Hz. 1.2 Object The principal object of this standard is to prescribe preferred ratings and characteristics and to select from IEC 60384-1, the appropriate quality assessment procedures, tests and measuring methods and to give general performance requirements for this type of capacitor. Test severit
10、ies and requirements prescribed in detail specifi cations referring to this sectional specifi cation shall be of equal or higher performance level, lower performance levels not being permitted. A further object of this standard is to provide a schedule of safety tests to be used by national testing
11、stations in countries where approval by such stations is required. 1.3 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced do
12、cument (including any amendments) applies. IEC 60060-1, High-voltage test techniques Part 1: General defi nitions and test requirements IEC 60063, Preferred number series for resistors and capacitors IEC 60068-1, Environmental testing Part 1: General and guidance IEC 60068-2-17, Environmental testin
13、g Part 2: Tests Test Q: Sealing IEC 60335-1, Household and similar electrical appliances Safety Part 1: General requirements IEC 60384-1, Fixed capacitors for use in electronic equipment Part 1: Generic specifi cation IEC 60384-14-4, Fixed capacitors for use in electronic equipment Part 14: Blank de
14、tail specifi cation: Fixed capacitors for electromagnetic interference supply and connection to the supply mains Assessment level D AUGUST 31, 2007SUBJECT 1414-2- Copyright Underwriters Laboratories Inc. Provided by IHS under license with ULLicensee=IHS Employees/1111111001, User=Wing, Bernie Not fo
15、r Resale, 09/03/2007 00:50:04 MDTNo reproduction or networking permitted without license from IHS -,-,- FOR INTERNAL UL OR CSDS USE ONLY NOT FOR OUTSIDE DISTRIBUTION IEC 60664-1, Insulation coordination for equipment within low-voltage systems Part 1: Principles, requirements and tests IEC 60760, Fl
16、at, quick-connect terminations IEC 60940, Guidance information on the application of capacitors, resistors, inductors and complete fi lter units for radio interference suppression IEC 61140, Protection against electric shock Common aspects for installation and equipment CISPR 17, Methods of measurem
17、ent of the suppression characteristics of passive radio interference fi lters and suppression components IEC QC 001005, IEC Quality Assessment System for Electronic Components (IECQ) Register of Firms, Products and Services approved under the IECQ System, including ISO 9000 ISO 7000-DB1, Graphical s
18、ymbols for use on equipment Index and synopsis 1 DB refers to the ISO on-line database. 1.4 Information to be given in a detail specifi cation Detail specifi cations shall be derived from the relevant blank detail specifi cation. Detail specifi cations shall not specify requirements inferior to thos
19、e of the generic, sectional or blank detail specifi cation. When more severe requirements are included, they shall be listed in 1.9 of the detail specifi cation, and indicated in the test schedules, for example, by an asterisk. The following information shall be given in each detail specifi cation a
20、nd the values quoted shall preferably be selected from the appropriate clause of this sectional specifi cation. NOTE The information given in 1.4.1 may for convenience be presented in tabular form. 1.4.1 Outline drawing and dimensions There shall be an illustration of the capacitor as an aid to easy
21、 recognition and for comparison of the capacitor with others. Dimensions and their associated tolerances, which affect interchangeability and mounting, shall be given in the detail specifi cation. All dimensions shall preferably be stated in millimetres; however, when the original dimensions are giv
22、en in inches, the converted metric dimensions in millimetres shall be added. Normally, the numerical values shall be given for the length, width and height of the body and the wire spacing, or for cylindrical types, the body diameter and the length and diameter of the terminations. When necessary, f
23、or example when a number of capacitance values/voltage ranges are covered by a detail specifi cation, their dimensions and their associated tolerances shall be placed in a table below the drawing. AUGUST 31, 2007SUBJECT 1414-3- Copyright Underwriters Laboratories Inc. Provided by IHS under license w
24、ith ULLicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 09/03/2007 00:50:04 MDTNo reproduction or networking permitted without license from IHS -,-,- FOR INTERNAL UL OR CSDS USE ONLY NOT FOR OUTSIDE DISTRIBUTION When the confi guration is other than that described above, the detai
25、l specifi cation shall state such dimensional information as will adequately describe the capacitor. When the capacitor is not designed for use on printed boards, this shall be clearly stated in the detail specifi cation. 1.4.2 Mounting The detail specifi cation shall specify the method of mounting
26、to be applied for normal use and for the application of the vibration, bump or shock tests. The capacitors shall be mounted by their normal means. The design of the capacitor may be such that special mounting fi xtures are required in its use. In this case, the detail specifi cation shall describe t
27、he mounting fi xtures and they shall be used in the application of the vibration, bump or shock tests. NOTE If recommendations for mounting for normal use are made, they should be included in the detail specifi cation under 1.8 Additional information (Not for inspection purposes). If recommendations
28、 are included, a warning can be given that the full vibration, bump and shock performance may not be available if mounting methods other than those specifi ed in 1.1 of the detail specifi cation are used. 1.4.3 Ratings and characteristics The ratings and characteristics shall be in accordance with t
29、he relevant clauses of this specifi cation, together with the following. 1.4.3.1 Rated capacitance range See 2.2.1. NOTE When products approved to the detail specifi cation have different ranges, the following statement should be added: The range of values available in each voltage range is given in
30、 IEC QC 001005. 1.4.3.2 Rated resistance range (if applicable) See 2.2.4. 1.4.3.3 Particular characteristics Additional characteristics may be listed, when they are considered necessary to specify the component adequately for design and application purposes. AUGUST 31, 2007SUBJECT 1414-4- Copyright
31、Underwriters Laboratories Inc. Provided by IHS under license with ULLicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 09/03/2007 00:50:04 MDTNo reproduction or networking permitted without license from IHS -,-,- FOR INTERNAL UL OR CSDS USE ONLY NOT FOR OUTSIDE DISTRIBUTION 1.4.4 M
32、arking The detail specifi cation shall specify the content of the marking on the capacitor and on the package. See also 1.6 of this specifi cation. 1.5 Terms and defi nitions For the purposes of this document, the terms and defi nitions of IEC 60384-1, as well as the following, apply. NOTE Some defi
33、 nitions of IEC 60384-1 have been expanded, and this is indicated by reference to this note. 1.5.1 a.c. capacitor capacitor designed essentially for application with a power-frequency alternating voltage NOTE AC capacitors may be used on d.c. supplies having the same voltage as the a.c. r.m.s. rated
34、 voltage of the capacitor. 1.5.2 electromagnetic interference suppression capacitor (radio interference suppression capacitor) capacitor used for the reduction of electromagnetic interference caused by electrical or electronic apparatus, or other sources 1.5.3 capacitor or RC unit of Class X capacit
35、or or RC unit of a type suitable for use in situations where failure of the capacitor or RC unit would not lead to danger of electrical shock but could result in a risk of fi re Class X capacitors are divided into three subclasses (see Table 1) according to the peak voltage of the impulses superimpo
36、sed on the mains voltage to which they may be subjected in service. Such impulses may arise from lightning strikes on outside lines, from switching in neighbouring equipment, or switching in the equipment in which the capacitor is used. This is generated text for fi gtxt. AUGUST 31, 2007SUBJECT 1414
37、-5- Copyright Underwriters Laboratories Inc. Provided by IHS under license with ULLicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 09/03/2007 00:50:04 MDTNo reproduction or networking permitted without license from IHS -,-,- FOR INTERNAL UL OR CSDS USE ONLY NOT FOR OUTSIDE DISTRI
38、BUTION 1.5.4 capacitor or RC unit of Class Y capacitor or RC unit of a type suitable for use in situations where failure of the capacitor could lead to danger of electric shock Class Y capacitors are further divided into four subclasses, Y1, Y2, Y3 and Y4, as shown in Table 2. Table 2 Classifi catio
39、n of Class Y capacitors SubclassType of insulation bridgedRange of rated voltagesPeak impulse voltage before endurance test Y1Double insulation or reinforced insulation 500 V8,0 kV Y2Basic insulation or supplementary insulation 150 V5,0 kV 300 V Y3Basic insulation or supplementary insulation 150 VNo
40、ne 250 V Y4Basic insulation or supplementary insulation 1 F 4.15.3Final measurementsCapacitanceSee Table 17 Tan at same frequency as initial measurement (not for RC units) See Table 17 Resistance (if applicable) See Table 17 Insulation resistanceSee Table 17 Group 5Non-destructiveSee Table 4 4.16Rad
41、iofrequency characteristics If required in the detail specifi cation; see detail specifi cation for measuring method See detail specifi cation Group 6DestructiveSee Table 4 4.17 Passive fl ammabilitySee 4.17.1 Group 7DestructiveSee Table 4 4.18 Active fl ammabilitySee 4.18.4 a) Subclause numbers of
42、test conditions and requirements refer to Clause 4. b) n= number of specimens,c= number of permissible nonconforming items. c) When, for a ceramic capacitor, a precise measurement of capacitance drift is required, preconditioning according to Annex G should be performed as advised by the manufacture
43、r. AUGUST 31, 2007SUBJECT 1414-26- Copyright Underwriters Laboratories Inc. Provided by IHS under license with ULLicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 09/03/2007 00:50:04 MDTNo reproduction or networking permitted without license from IHS -,-,- FOR INTERNAL UL OR CSDS
44、USE ONLY NOT FOR OUTSIDE DISTRIBUTION 3.5 Quality conformance inspection Before submission to the quality conformance inspection an appropriate 100 % voltage proof test between terminations according to Table 10 shall be made. The details of this test shall be the prerogative of the manufacturer, bu
45、t the time shall be not less than 1 s. If the test is performed in a time period between 1 s and 2 s the voltage of Table 10 shall be increased to values above curve B of Figure 6. This is generated text for fi gtxt. If a d.c. test voltage is used instead of a.c. for Y-capacitors, it shall be not le
46、ss than 1,5 times the a.c. test voltage in Table 10 and further increased to values above curve B of Figure 6. All nonconforming items shall be removed from the lot prior to lot-by-lot testing. 3.5.1 Formation of inspection lots Figure 6 Test duration (s) AUGUST 31, 2007SUBJECT 1414-27- Copyright Un
47、derwriters Laboratories Inc. Provided by IHS under license with ULLicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 09/03/2007 00:50:04 MDTNo reproduction or networking permitted without license from IHS -,-,- FOR INTERNAL UL OR CSDS USE ONLY NOT FOR OUTSIDE DISTRIBUTION 3.5.1.1 G
48、roups A and B inspection These tests shall be carried out on a lot-by-lot basis according to Table 8. A manufacturer may aggregate the current production into inspection lots subject to the following safeguards: a) the inspection lot shall consist of structurally similar capacitors (see 3.2); b1) the sample tested shall be representative of the values and dimensions contained in the inspection lot: in relation to their number; with a minimum of fi ve of any one value; b2) if there are less than fi ve of any one value in the s