《标准.pdf》由会员分享，可在线阅读，更多相关《标准.pdf（10页珍藏版）》请在三一文库上搜索。
1、 AMSC N/A 1 of 10 FSC 5999 DISTRIBUTION STATEMENT A . Approved for public release; distribution is unlimited. MIL-DTL-83528/13E 15 November 2001 SUPERSEDING MIL-G-83528/13D 28 March 1994 DETAIL SPECIFICATION SHEET GASKETING MATERIAL, CONDUCTIVE, SHIELDING GASKET, ELECTRONIC, ELASTOMER, ELECTRICAL, E
2、MI/RFI, WAVEGUIDE This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the relay described herein shall consist of this specification and the latest issue of MIL-DTL-83528. Flange designation per MIL-F-3922 Frequency rang
3、e (GHz) Band EIA wave- guide size Waveguide designation per MIL-DTL-85 UG CPR CMR Flange type Gasket config- uration Part or Identifying Number (PIN) M83528/013X UG-599/U Cover A 001 1/ 26.5-40.0 Ka WR28 RG-96/U (Silver) UG-600A/U Choke E 002 RG-53/U (Brass) UG-595/U UG-597/U Cover A 003 1/ 18.0-26.
4、5 K WR42 RG-121/U (Aluminum) UG-596A/U UG-598A/U Choke E 004 RG-91 (Brass) UG-419/U Cover A 005 1/ 12.4-18.0 Ku WR62 RG-107/U (Silver) UG-541A/U Choke E 006 Cover A 007 10.0-15.0 WR75 Choke E 008 UG-39/U UG-135/U Cover A 009 UG-1736/U UF-1737/U CPR-90F Flat contact A 010 1/ UG-136A/U UG-40A/U Choke
5、E 011 UG-136B/U UG-40B/U Choke E 012 8.2-12.4 X WR90 RG-52/U (Brass) RG-67/U (Aluminum) UG-1360/U UG-1361/U CPR-90G Contact C 013 7.0-11.0 WR102 UG-1494/U Choke E 014 See footnote at end of table. INCH-POUND MIL-DTL-83528/13E 2 Flange designation per MIL-F-3922 Frequency range (GHz) Band EIA wave- g
6、uide size Waveguide designation per MIL-DTL-85 UG CPR CMR Flange type Gasket config- uration Part or Identifying Number (PIN) M83528/013X UG-51/U UG-138/U Cover A 015 UG-1734/U UF-1735/U CPR-112F Flat contact A 016 1/ UG-52B/U UG-137B/U Choke E 017 7.05-10.0 X1 WR112 RG-51/U (Brass) RG-68/U (Aluminu
7、m) UG-1358/U UF-1359/U CPR-112G Contact C 018 UG-334/U UG-441/U Cover B 019 UG-1732/U UG-1733/U CPR-137F Flat contact 020 1/ CMR-137 Flat contact A 021 1/ UG-343B/U UG-440B/U Choke D 022 5.85-8.2 Xb WR137 RG-50/U (Brass) RG-106/U (Aluminum) UG-1356/U UG-1357/U CPR-137G Contact C 023 UG-1730/U UG-173
8、1/U CPR-159F Flat contact A 024 1/ 4.9-7.05 WR159 CMR-159 Flat contact A 025 1/ UG-149A/U UG-407/U Cover B 26 UG-1728/U UG-1729/U CPR-187F Flat contact A 027 1/ CMR-187 Flat contact A 028 1/ UG-148C/U UG-406B/U Choke D 029 3.95-5.85 C WR187 RG-49/U (Brass) RG-95/U (Aluminum) UG-1352/U UG-1353/U CPR-
9、187G Contact C 030 UG-1726/U UG-1727/U CPR-229F Flat contact A 031 1/ 3.30-4.90 WR229 CMR-229 Flat contact A 032 1/ See footnote at end of table. MIL-DTL-83528/13E 3 Frequency range (GHz) Band EIA wave- guide size Waveguide designation per MIL-DTL-85 Flange designation per MIL-F-3922 Flange type Gas
10、ket config- uration Part or Identifying Number (PIN) M83528/013X UG-53/U UG-584/U Cover B 033 1/ UG-1724/U UG-1725/U CPR-284F Flat contact A 034 1/ CMR-284 Flat contact A 035 1/ UG-54B/U UG-585A/U Choke E 036 2.6-3.95 S WR284 RG-48/U (Brass) RG-75/U (Aluminum) UG-1348/U UG-1349/U CPR-284G Contact C
11、037 UG-533/U UG-554/U Flat contact A 038 1/ 2.2-3.3 WR340 RG-112/U (Brass) RG-112/U (Aluminum) CPR-340F Flat contact A 039 1/ UG-435A/U UG-437A/U Flat contact A 040 1/ 1.7-2.6 W WR430 RG-104/U (Brass) RG-105/U (Aluminum) CPR-430F Flat contact A 041 1/ 1.12-1.7 L WR650 RG-69/U (Brass) RG-103/U (Alumi
12、num) UG-417A/U UG-418A/U Flat contact A 042 1/ 1/ This gasket will seal a maximum pressure of 20 psig. MIL-DTL-83528/13E 4 CONFIGURATION A - DIE CUT SQUARE AND RECTANGULAR NOTE: Shaded area indicates optional raised lip. When included, the lip shall be a nominal of .187 (4.75 mm) wide. Thickness T1
13、shall be .004 (0.10 mm) .002 (0.05 mm). Lip is standard on configuration A dash numbers without footnote 1/ reference in table I. For dash numbers in table I with footnote 1/ reference, lip is optional. Dimensions (Configuration A) A .015 (0.38) B .015 (0.38) C .015 (0.38) -.000 (0.00) D .015 (0.38)
14、 -.000 (0.00) E 1/ .010 (0.25) T .003 (0.08) F Radius .010 (0.25) Part or Identifying Number (PIN) M83528/013X Cross section area (cm2) 2/ .750 (19.05) .750 (19.05) .145 (3.68) .285 (7.24) .116 (2.95) .027 (0.69) .469 (11.91) 001 .0082 .875 (22.23) .875 (22.23) .175 (4.45) .425 (10.80) .116 (2.95) .
15、027 (0.69) .563 (14.30) 003 .0095 1.313 (33.35) 1.313 (33.35) .630 (16.00) .320 (8.13) .140 (3.56) .027 (0.69) .875 (22.23) 005 .0092 1.496 (38.00) 1.496 (38.00) .760 (19.30) .385 (9.78) .155 (3.94) .027 (0.69) .450 (11.43) 007 .0099 1.625 (41.28) 1.625 (41.28) .905 (22.99) .405 (10.29) .169 (4.29)
16、.027 (0.69) .469 (11.91) 009 .0097 1.594 (40.49) 2.094 (53.19) .405 (10.29 .905 (22.99) .169 (4.29) .027 (0.69) .250 (6.35) 010 .0161 MIL-DTL-83528/13E 5 FIGURE 1. Configurations and dimensions. Dimensions (Configuration A Continued.) A .015 (0.38) B .015 (0.38) C .015 (0.38) -.000 (0.00) D .015 (0.
17、38) -.000 (0.00) E 1/ .010 (0.25) T .003 (0.08) F Radius .010 (0.25) Part or Identifying Number (PIN) M83528/013X Cross section area (cm2) 2/ 1.875 (47.63) 1.875 (47.63) 1.130 (28.70) .505 (12.83) .180 (4.57) .027 (0.69) 1.15 (29.21) 015 .0101 1.750 (44.45) 2.500 (63.50) .505 (12.83) 1.130 (28.70) .
18、171 (4.34) .027 (0.69) .250 (6.35) 016 .076 1.937 (49.20) 2.687 (68.25) .633 (16.08) 1.380 (35.05) .206 (5.23) .027 (0.69) .250 (6.35) 020 .0176 1.531 (38.89) 2.281 (57.94) .632 (16.05) 1.382 (35.10) .150 (3.81) .027 (0.69) .125 (3.18) 021 .0121 2.438 (61.93) 3.188 (80.98) .805 (20.45) 1.600 (40.64)
19、 .257 (6.53) .027 (0.69) .313 (7.95) 024 .0220 1.750 (44.45) 2.500 (63.50) .800 (20.32) 1.600 (40.64) .160 (4.06) .150 (3.81) .027 (0.69) .125 (3.18) 025 .0128 3.500 (88.90) 2.500 (63.50) 1.880 (47.75) .880 (22.35) .266 (6.76) .027 (0.69) .313 (7.95) 027 .0219 1.784 (45.31) 2.781 (70.64) .882 (22.40
20、) 1.882 (47.80) .156 (3.96) .141 (3.58) .027 (0.69) .125 (3.18) 028 .0122 2.750 (69.85) 3.875 (98.43) 1.155 (29.34) 2.300 (58.42) .270 (6.86) .027 (0.69) .312 (7.92) 031 .0215 2.000 (50.80) 3.156 (80.16) 1.155 (29.34) 2.300 (58.42) .150 (3.81) .027 (0.69) .125 (3.18) 032 .0114 4.500 (114.30) 3.000 (
21、76.20) 2.850 (72.39) 1.350 (34.29) .266 (6.76) .027 (0.69) .313 (7.95) 034 .0223 3.844 (97.64) 2.344 (59.54) 2.850 (72.39) 1.350 (34.29) .172 (4.37) .188 (4.78) .027 (0.69) .125 (3.18) 035 .0134 3.750 (95.25) 5.440 (138.18) 1.710 (43.43) 3.410 (86.61) .264 (6.71) .250 (6.35) .027 (0.69) .250 (6.35)
22、038 .0275 3.750 (95.25) 5.438 (138.13) 1.710 (43.43) 3.410 (86.61) .266 (6.76) .027 (0.69) .250 (6.35) 039 .0275 4.188 (106.38) 6.344 (161.14) 2.160 (54.86) 4.310 (109.47) .266 (6.76) .281 (7.14) .027 (0.69) .250 (6.35) 040 .0274 6.344 (161.14) 4.188 (106.38) 4.310 (109.47) 2.160 (54.86) .266 (6.76)
23、 .027 (0.69) .250 (6.35) 041 .0275 5.438 (138.13) 8.688 (220.68) 3.260 (82.80) 6.510 (165.35) .250 (6.35) .328 (8.33) .027 (0.69) .250 (6.35) 042 .0294 1/ Number and location of holes conform to holes in standard waveguide flanges identified in table I. Where two hole diameters are given, flange has
24、 holes of two different diameters. 2/ For calculation of volume resistivity (surface probe). MIL-DTL-83528/13E 6 CONFIGURATION B DIE CUT CIRCULAR NOTE: Shaded area indicates optional raised lip. When included, the lip shall be a nominal of .187 (4.75 mm) wide. Thickness T1 shall be .004 (0.10 mm) .0
25、02 (0.05 mm). Lip is standard on configuration B dash numbers without footnote 1/ reference in table I. For dash numbers in table I with footnote 1/ reference, lip is optional. Dimensions (Configuration B) A .015 (0.38) B .015 (0.38) -0.000 (0.00) C .015 (0.38) -0.000 (0.00) D 1/ .010 (0.25) T .005
26、(0.13) Part or Identifying Number (PIN) M83528/013X Cross section area (cm2) 2/ 3.125 (79.38) .632 (16.05) 1.382 (35.10) .234 (5.94) .027 (0.69) 019 .0337 3.625 (92.08) .882 (22.40) 1.882 (47.80) .234 (5.94) .027 (0.69) 026 .0370 5.312 (134.92) 1.350 (34.29) 2.850 (72.39) .290 (7.37) .027 (0.69) 033
27、 .0535 1/ Number and location of holes conform to holes in standard waveguide flanges identified in table I. 2/ For calculation of volume resistivity (surface probe). FIGURE 1. Configurations and dimensions Continued. MIL-DTL-83528/13E 7 CONFIGURATION C MOLDED RECTANGULAR WITH “O“ CROSS SECTION NOTE
28、: Molding flash of .003 (0.08 mm) in width (maximum) and .005 (0.13 mm) in thickness (maximum) is allowed. Dimensions (Configuration C) Part or Identifying Number (PIN) M83528/013X Cross section area (cm2) 1/ 1.368 (34.75) .012 (0.03) .868 (22.05) .010 (0.25) .103 (2.62) .003 (0.08) 013 .0538 1.616
29、(41.05) .015 (0.38) .991 (25.17) 0.010 (0.25) .103 (2.62) .003 (0.08) 018 .0538 1.866 (41.05) .015 (0.38) 1.116 (28.35) .012 (0.30) .103 (2.62) .003 (0.08) 023 .0538 2.449 (62.20) .020 (0.51) 1.449 (36.80) .013 (0.33) .139 (3.53) .004 (0.10) 030 .0979 3.451 (87.66) .024 (0.61) 1.951 (49.56) .018 (0.
30、46) .139 (3.53) .004 (0.10) 037 .0979 1/ For calculation of volume resistivity (surface probe). FIGURE 1. Configurations and dimensions Continued. MIL-DTL-83528/13E 8 CONFIGURATION D MOLDED CIRCULAR WITH “O“ CROSS SECTION NOTE: Molding flash of .003 (0.08 mm) in width (maximum) and .005 (0.13 mm) in
31、 thickness (maximum) is allowed. Dimensions (Configuration D) D (ID) T Part or Identifying Number (PIN) M83528/013X Cross section area(cm2) 1/ 2.011 (51.08) .018 (0.46) .139 (3.53) .004 (0.10) 022 .0979 2.683 (68.15) .024 (0.61) .115 (2.92) .004 (0.10) 029 .0670 1/ For calculation of volume resistiv
32、ity (surface probe). FIGURE 1. Configuration and dimensions Continued. MIL-DTL-83528/13E 9 CONFIGURATION E - - MOLDED CIRCULAR WITH “D“ CROSS SECTION NOTE: Molding flash of .003 (0.08 mm) in width (maximum) and .005 (0.13 mm) in thickness (maximum) is allowed. Dimensions (Configuration E) A B D (ID)
33、 T Part or Identifying Number (PIN) M83528/013X Cross section area (cm2) 1/ .056 (1.42) .041 (1.04) .410 (10.41) .082 (2.08) 002 .025 .048 (1.22) .039 (0.99) .587 (14.91) .078 (1.98) 004 .020 .125 (3.18) .078 (1.98) .885 (22.48) .155 (3.94) 006 .109 .065 (1.65) .049 (1.24) 1.122 (28.50) .099 (2.51)
34、008 .035 .088 (2.24) .048 (1.22) 1.340 (34.04) .095 (2.41) 011 .048 .077 (1.96) .058 (1.47) 1.310 (33.27) .115 (2.92) 012 .048 .085 (2.16) .048 (1.22) 1.392 (35.36) 0.95 (2.41) 014 .046 .078 (2.16) .053 (1.35) 1.550 (39.37) .105 (2.67) 017 .045 .188 (4.78) .120 (3.05) 3.910 (99.31) .026 (0.66) .240
35、(6.10) 036 .251 1/ For calculation of volume resistivity (surface probe). NOTES: 1/ Dimensions are in inches; metric equivalents are given in parenthesis and are for general information only. 2/ Unless otherwise indicated, tolerances shall be as follows: Dimensions Tolerance Under .101 (2.57) .101 t
36、o .200 (2.57 to 5.08) .201 to .300 (5.10 to 7.62) .301 to .500 (7.62 to 12.70) Over .500 (12.70) .005 (0.13) .008 (0.20) .010 (0.25) .015 (0.38) .020 (0.51) FIGURE 1. Configurations and dimensions Continued. MIL-DTL-83528/13E 10 SELECTION GUIDE: See table I. REQUIREMENTS: Design and interface: See f
37、igure 1 and table I. Materials: Configuration A: Type G. Configuration B: Type G. Configuration C: Types C, F, H, or K. Configuration D: Types C, F, H, or K. Configuration E: Types C, F, H, or K. Part or Identifying Number (PIN): See table I and figure 1. An “X“ in the PIN represents the material ty
38、pe (see above). PIN example: M83528/013G001. Gaskets with optional high-pressure raised lip (see table I and figure 1) will have a “Z“ added to their PINs. Example: M83528/013G001Z. Supersession information: See table II. TABLE II. Supersession information. MIL-G-83528/13B PIN M83528/013X Superseded
39、 MIL-G-83528/13A PIN M83528/013X Superseded DESC drawing PIN 85118X 002 001 001 004 002 002 006 003 003 008 004 004 012 005 005 011 006 006 014 007 007 017 008 008 036 009 009 1/ “X“ in the PIN indicates the applicable material type. Custodian: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 11 (Project 5999-0375-13) DLA - CC Review activities: Air Force 19, 99 NASA NA