OI-MF参数说明书.pdf

《OI-MF参数说明书.pdf》由会员分享，可在线阅读，更多相关《OI-MF参数说明书.pdf（742页珍藏版）》请在三一文库上搜索。

1、 PARAMETER MANUAL FANUC Series 0+-MODEL F B-64610EN/01 No part of this manual may be reproduced in any form. All specifications and designs are subject to change without notice. The products in this manual are controlled based on Japans “Foreign Exchange and Foreign Trade Law”. The export of from Ja

2、pan subject to an export license by the government of Japan. Other models in this manual may also be subject to export controls. Further, re-export to another country may be subject to the license of the government of the country from where the product is re-exported. Furthermore, the product may al

3、so be controlled by re-export regulations of the United States government. Should you wish to export or re-export these products, please contact FANUC for advice. In this manual we have tried as much as possible to describe all the various matters. However, we cannot describe all the matters which m

4、ust not be done, or which cannot be done, because there are so many possibilities. Therefore, matters which are not especially described as possible in this manual should be regarded as ”impossible”. B-64610EN/01 DEFINITION OF WARNING, CAUTION, AND NOTE s-1 DEFINITION OF WARNING, CAUTION, AND NOTE T

5、his manual includes safety precautions for protecting the user and preventing damage to the machine. Precautions are classified into Warning and Caution according to their bearing on safety. Also, supplementary information is described as a Note. Read the Warning, Caution, and Note thoroughly before

6、 attempting to use the machine. WARNING Applied when there is a danger of the user being injured or when there is a danger of both the user being injured and the equipment being damaged if the approved procedure is not observed. CAUTION Applied when there is a danger of the equipment being damaged,

7、if the approved procedure is not observed. NOTE The Note is used to indicate supplementary information other than Warning and Caution. Read this manual carefully, and store it in a safe place. B-64610EN/01 PREFACE p-1 PREFACE Applicable models The models covered by this manual, and their abbreviatio

8、ns are : Model name Abbreviation FANUC Series 0i-TF 0i-TF FANUC Series 0i-MF 0i-MF Series 0i-F Series 0i NOTE 1 For an explanatory purpose, the following descriptions may be used according to the types of path control used: - 0i-TF : For the lathe system (T series) - 0i-MF : For the machining center

9、 system (M series) 2 Some functions described in this manual may not be applied to some products. For details, refer to the DESCRIPTIONS (B-64602EN). Related manuals of Series 0i- MODEL F The following table lists the manuals related to Series 0i-F. This manual is indicated by an asterisk(*). Table

10、1 Related manuals Manual name Specification number DESCRIPTIONS B-64602EN CONNECTION MANUAL (HARDWARE) B-64603EN CONNECTION MANUAL (FUNCTION) B-64603EN-1 OPERATORS MANUAL (Common to Lathe System/Machining Center System) B-64604EN OPERATORS MANUAL (For Lathe System) B-64604EN-1 OPERATORS MANUAL (For

11、Machining Center System) B-64604EN-2 MAINTENANCE MANUAL B-64605EN PARAMETER MANUAL B-64610EN * Programming Macro Executor PROGRAMMING MANUAL B-63943EN-2 Macro Compiler PROGRAMMING MANUAL B-66263EN C Language Executor PROGRAMMING MANUAL B-63943EN-3 PMC PMC PROGRAMMING MANUAL B-64513EN Network PROFIBU

12、S-DP Board CONNECTION MANUAL B-63993EN Industrial Ethernet CONNECTION MANUAL B-64013EN Fast Ethernet / Fast Data Server OPERATORS MANUAL B-64014EN DeviceNet Board CONNECTION MANUAL B-64043EN FL-net Board CONNECTION MANUAL B-64163EN CC-Link Board CONNECTION MANUAL B-64463EN Operation guidance functio

13、n MANUAL GUIDE i (Common to Lathe System/Machining Center System) OPERATORS MANUAL B-63874EN MANUAL GUIDE i (For Machining Center System) OPERATORS MANUAL B-63874EN-2 MANUAL GUIDE i (Set-up Guidance Functions) OPERATORS MANUAL B-63874EN-1 MANUAL GUIDE 0 i OPERATORS MANUAL B-64434EN TURN MATE i OPERA

14、TORS MANUAL B-64254EN PREFACE B-64610EN/01 p-2 Manual name Specification number Dual Check Safety Dual Check Safety CONNECTION MANUAL B-64483EN-2 Related manuals of SERVO MOTOR i/ i series The following table lists the manuals related to SERVO MOTOR i/i series Table 2 Related manuals Manual name Spe

15、cification number FANUC AC SERVO MOTOR i series DESCRIPTIONS B-65262EN FANUC AC SPINDLE MOTOR i series DESCRIPTIONS B-65272EN FANUC AC SERVO MOTOR i series DESCRIPTIONS B-65302EN FANUC AC SPINDLE MOTOR i series DESCRIPTIONS B-65312EN FANUC SERVO AMPLIFIER i series DESCRIPTIONS B-65282EN FANUC SERVO

16、AMPLIFIER i series DESCRIPTIONS B-65322EN FANUC SERVO MOTOR is series FANUC SERVO MOTOR i series FANUC AC SPINDLE MOTOR i series FANUC SERVO AMPLIFIER i series MAINTENANCE MANUAL B-65285EN FANUC SERVO MOTOR is series FANUC AC SPINDLE MOTOR i series FANUC SERVO AMPLIFIER i series MAINTENANCE MANUAL B

17、-65325EN FANUC AC SERVO MOTOR i series FANUC AC SERVO MOTOR i series FANUC LINEAR MOTOR LiS series FANUC SYNCHRONOUS BUILT-IN SERVO MOTOR DiS series PARAMETER MANUAL B-65270EN FANUC AC SPINDLE MOTOR i/i series, BUILT-IN SPINDLE MOTOR Bi series PARAMETER MANUAL B-65280EN This manual mainly assumes th

18、at the FANUC SERVO MOTOR i series of servo motor is used. For servo motor and spindle information, refer to the manuals for the servo motor and spindle that are actually connected. B-64610EN/01 TABLE OF CONTENTS c-1 TABLE OF CONTENTS DEFINITION OF WARNING, CAUTION, AND NOTE.s-1 PREFACEp-1 1 DISPLAYI

19、NG PARAMETERS.1 2 SETTING PARAMETERS FROM MDI2 3 INPUTTING AND OUTPUTTING PARAMETERS THROUGH THE RS232C INTERFACE4 3.1 OUTPUTTING PARAMETERS THROUGH THE RS232C INTERFACE.4 3.2 INPUTTING PARAMETERS THROUGH THE RS232C INTERFACE.5 3.3 I/O FORMATS .6 3.3.1 Keywords .6 3.3.2 Inch/Metric Switching7 3.3.3

20、Bit Format.7 3.3.4 Bit Machine Group Format 7 3.3.5 Bit Path Format 8 3.3.6 Bit Axis Format8 3.3.7 Bit Spindle Format .9 3.3.8 Byte/Word/Two-Word Format.9 3.3.9 Byte/Word/Two-Word Machine Group Format.9 3.3.10 Byte/Word/Two-Word Path Format.10 3.3.11 Byte/Word/Two-Word Axis Format 10 3.3.12 Byte/Wor

21、d/Two-Word Spindle Format11 3.3.13 Real Number Format11 3.3.14 Real Number Machine Group Format12 3.3.15 Real Number Path Format12 3.3.16 Real Number Axis Format13 3.3.17 Real Number Spindle Format.13 3.3.18 Start and End of a Record.14 4 DESCRIPTION OF PARAMETERS15 4.1 INPUT TYPE15 4.2 DATA TYPE.15

22、 4.3 REPRESENTATION OF PARAMETERS 16 4.4 STANDARD PARAMETER SETTING TABLES.17 4.5 PARAMETERS OF SETTING19 4.6 PARAMETERS OF RS232C INTERFACE 21 4.6.1 Parameters Common to All Channels 22 4.6.2 Parameters of Channel 1 (I/O CHANNEL=0) .26 4.6.3 Parameters of Channel 1 (I/O CHANNEL=1) .28 4.6.4 Paramet

23、ers of Channel 2 (I/O CHANNEL=2) .29 4.7 PARAMETERS OF CNC SCREEN DISPLAY FUNCTIONS29 4.8 PARAMETERS OF ETHERNET/DATA SERVER FUNCTIONS30 4.9 PARAMETERS OF POWER MATE CNC35 4.10 PARAMETERS OF ETHERNET/ INDUSTRIAL ETHERNET FUNCTIONS.36 4.11 PARAMETERS OF SYSTEM CONFIGURATION .38 TABLE OF CONTENTS B-64

24、610EN/01 c-2 4.12 PARAMETERS OF AXIS CONTROL/INCREMENT SYSTEM (1 OF 3) 41 4.13 PARAMETERS OF COORDINATE SYSTEM (1 OF 2) .52 4.14 PARAMETERS OF STORED STROKE CHECK.59 4.15 PARAMETERS OF THE CHUCK AND TAIL STOCK BARRIER.66 4.16 PARAMETERS OF FEEDRATE70 4.17 PARAMETERS OF ACCELERATION/DECELERATION CONT

25、ROL82 4.18 PARAMETERS OF SERVO (1 OF 2)99 4.19 PARAMETERS OF DI/DO (1 OF 2).135 4.20 PARAMETERS OF DISPLAY AND EDIT (1 OF 6)147 4.21 PARAMETERS OF PROGRAMS (1 OF 4)179 4.22 PARAMETERS OF PITCH ERROR COMPENSATION 194 4.23 PARAMETERS OF SPINDLE CONTROL .201 4.24 PARAMETERS OF TOOL COMPENSATION (1 OF 3

26、).247 4.25 PARAMETERS OF CANNED CYCLES.266 4.25.1 Parameters of Canned Cycle for Drilling (1 of 2)266 4.25.2 Parameters of Thread Cutting Cycle 275 4.25.3 Parameters of Multiple Repetitive Canned Cycle 276 4.25.4 Parameters of Canned Cycle for Drilling (2 of 2)280 4.25.5 Parameters of Canned Cycle f

27、or Grinding (for Grinding Machine) (1 of 2)285 4.26 PARAMETERS OF RIGID TAPPING 288 4.27 PARAMETERS OF SCALING/COORDINATE ROTATION.303 4.28 PARAMETERS OF SINGLE DIRECTION POSITIONING.305 4.29 PARAMETERS OF POLAR COORDINATE INTERPOLATION 306 4.30 PARAMETERS OF NORMAL DIRECTION CONTROL.307 4.31 PARAME

28、TERS OF INDEX TABLE INDEXING308 4.32 PARAMETERS OF FLEXIBLE SYNCHRONIZATION CONTROL (1 OF 2).311 4.33 PARAMETERS OF STRAIGHTNESS COMPENSATION (1 OF 2).315 4.34 PARAMETERS OF INCLINATION COMPENSATION 318 4.35 PARAMETERS OF CUSTOM MACROS.319 4.36 PARAMETERS OF PATTERN DATA INPUT341 4.37 PARAMETERS OF

29、POSITIONING BY OPTIMUM ACCELERATION.342 4.38 PARAMETERS OF SKIP FUNCTION .344 4.39 PARAMETERS OF EXTERNAL DATA INPUT/OUTPUT 354 4.40 PARAMETERS OF MANUAL HANDLE RETRACE (1 OF 2) 356 4.41 PARAMETERS OF GRAPHIC DISPLAY (1 OF 4) 362 4.42 PARAMETERS OF SCREEN DISPLAY COLORS (1 OF 2)364 4.43 PARAMETERS O

30、F RUN HOUR AND PARTS COUNT DISPLAY.365 4.44 PARAMETERS OF TOOL MANAGEMENT FUNCTIONS (1 OF 2).368 4.45 PARAMETERS OF TOOL LIFE MANAGEMENT (1 OF 2)369 4.46 PARAMETERS OF POSITION SWITCH FUNCTIONS.377 4.47 PARAMETERS OF MANUAL OPERATION AND AUTOMATIC OPERATION (1 OF 2).381 4.48 PARAMETERS OF MANUAL HAN

31、DLE (1 OF 2) 384 4.49 PARAMETERS OF REFERENCE POINT WITH MECHANICAL STOPPER .389 4.50 PARAMETERS OF SOFTWARE OPERATORS PANEL391 B-64610EN/01 TABLE OF CONTENTS c-3 4.51 PARAMETERS OF PROGRAM RESTART (1 OF 2).394 4.52 PARAMETERS OF POLYGON TURNING397 4.53 PARAMETERS OF THE ELECTRONIC GEAR BOX (EGB) .4

32、05 4.54 PARAMETERS OF PMC AXIS CONTROL (1 OF 4).416 4.55 PARAMETERS OF MULTI-PATH CONTROL.426 4.56 PARAMETERS OF 0i -F / 0i Mate -F BASIC FUNCTIONS.430 4.57 PARAMETERS OF INTERFERENCE CHECK BETWEEN PATHS 436 4.58 PARAMETERS OF SYNCHRONOUS/COMPOSITE CONTROL AND SUPERIMPOSED CONTROL (1 OF 3).440 4.59

33、PARAMETERS OF ANGULAR AXIS CONTROL454 4.60 PARAMETERS OF AXIS SYNCHRONOUS CONTROL .458 4.61 PARAMETERS OF SEQUENCE NUMBER COMPARISON AND STOP466 4.62 PARAMETERS OF HIGH PRECISION OSCILLATION FUNCTION .467 4.63 PARAMETERS OF AI ADVANCED PREVIEW CONTROL (M SERIES) / AI CONTOUR CONTROL (1 OF 2) .468 4.

34、64 PARAMETERS OF HIGH-SPEED POSITION SWITCH (1 OF 2) .471 4.65 OTHER PARAMETERS 475 4.66 PARAMETERS OF MAINTENANCE.480 4.67 PARAMETERS OF THE INCORRECT OPERATION PREVENTION FUNCTION484 4.68 PARAMETERS OF AUTOMATIC DATA BACKUP492 4.69 PARAMETERS OF AXIS CONTROL 493 4.70 PARAMETERS OF PMC AXIS CONTROL

35、 (2 OF 4).494 4.71 PARAMETERS OF SCREEN DISPLAY COLORS (2 OF 2)495 4.72 PARAMETERS OF MANUAL OPERATION AND AUTOMATIC OPERATION (2 OF 2).495 4.73 PARAMETERS OF DUAL CHECK SAFETY (1 OF 2).496 4.74 PARAMETERS OF WAVEFORM DIAGNOSIS.496 4.75 PARAMETERS OF TROUBLE DIAGNOSIS FUNCTION496 4.76 PARAMETERS OF

36、SPINDLE CONTROL WITH SERVO MOTOR (1 OF 2).498 4.77 PARAMETERS OF TILTED WORKING PLANE INDEXING (M SERIES) / 3-DIMENSIONAL MANUAL FEED (M SERIES) (1 OF 2)506 4.78 PARAMETERS OF AXIS CONTROL/INCREMENT SYSTEM (2 OF 3) 507 4.79 PARAMETERS OF DI/DO (2 OF 2).508 4.80 PARAMETERS OF FEEDRATE CONTROL AND ACC

37、ELERATION/DECELERATION CONTROL509 4.81 PARAMETERS OF PROGRAM RESTART (2 OF 2).510 4.82 PARAMETERS OF COORDINATE SYSTEM (2 OF 2) .511 4.83 PARAMETERS OF SYNCHRONOUS/COMPOSITE CONTROL AND SUPERIMPOSED CONTROL (2 OF 3).514 4.84 PARAMETERS OF PROGRAMS (2 OF 4)514 4.85 PARAMETERS OF DISPLAY AND EDIT (2 O

38、F 6)515 4.86 PARAMETERS OF EMBEDDED MACRO (1 OF 2)522 4.87 PARAMETERS OF DISPLAY AND EDIT (3 OF 6)522 4.88 PARAMETERS OF GRAPHIC DISPLAY (2 OF 4) 526 TABLE OF CONTENTS B-64610EN/01 c-4 4.89 PARAMETERS OF DISPLAY AND EDIT (4 OF 6)530 4.90 PARAMETERS OF TOOL COMPENSATION (2 OF 3).546 4.91 PARAMETERS O

39、F OPTIMUM TORQUE ACCELERATION/DECELERATION FOR RIGID TAPPING549 4.92 PARAMETERS OF ARBITRARY SPEED THREADING552 4.93 PARAMETERS OF PROGRAMS (3 OF 4)555 4.94 PARAMETERS OF MACHINING QUALITY LEVEL ADJUSTMENT .574 4.95 PARAMETERS OF SERVO (2 OF 2)575 4.96 PARAMETERS OF PMC AXIS CONTROL (3 OF 4).577 4.9

40、7 PARAMETERS OF PMC.583 4.98 PARAMETERS OF EMBEDDED MACRO (2 OF 2)595 4.99 PARAMETERS OF HIGH-SPEED POSITION SWITCH (2 OF 2) .597 4.100 PARAMETERS OF MALFUNCTION PROTECTION.598 4.101 PARAMETERS OF MANUAL HANDLE (2 OF 2) 598 4.102 PARAMETERS OF SYNCHRONOUS/COMPOSITE CONTROL AND SUPERIMPOSED CONTROL (

41、3 OF 3).605 4.103 PARAMETERS OF PMC AXIS CONTROL (4 OF 4).606 4.104 PARAMETERS OF EXTERNAL DECELERATION POSITIONS EXPANSION607 4.105 PARAMETERS OF DISPLAY AND EDIT (5 OF 6)609 4.106 PARAMETERS OF TOOL MANAGEMENT FUNCTIONS (2 OF 2).617 4.107 PARAMETERS OF TOOL LIFE MANAGEMENT (2 OF 2)629 4.108 PARAME

42、TERS OF STRAIGHTNESS COMPENSATION (2 OF 2).630 4.109 PARAMETERS OF FLEXIBLE SYNCHRONIZATION CONTROL (2 OF 2).632 4.110 PARAMETERS OF PROGRAMS (4 OF 4)635 4.111 PARAMETERS OF MANUAL LINER/CIRCULAR INTERPOLATION636 4.112 PARAMETERS OF CANNED CYCLES FOR DRILLING M CODE OUTPUT IMPROVEMENT 638 4.113 PARA

43、METERS OF THE MACHINING CONDITION SELECTION FUNCTION639 4.114 PARAMETERS OF PARAMETER CHECK SUM FUNCTION.644 4.115 PARAMETERS OF DUAL CHECK SAFETY (2 OF 2).646 4.116 PARAMETERS OF SAFETY FUNCTION BY FL-net.646 4.117 PARAMETERS OF EtherNet/IP ADAPTER SAFETY FUNCTION 647 4.118 PARAMETERS OF AXIS CONTR

44、OL/INCREMENT SYSTEM (3 OF 3) 648 4.119 PARAMETERS OF LINEAR SCALE WITH ABSOLUTE ADDRESS REFERENCE POSITION 648 4.120 PARAMETERS OF FSSB (1 OF 2) .649 4.121 PARAMETERS OF SERVO GUIDE Mate .649 4.122 PARAMETERS OF GRAPHIC DISPLAY (3 OF 4) 650 4.123 PARAMETERS OF EMBEDDED ETHERNET.651 4.124 PARAMETERS

45、OF MANUAL HANDLE RETRACE (2 OF 2) 655 4.125 PARAMETERS OF AI ADVANCED PREVIEW CONTROL (M SERIES) / AI CONTOUR CONTROL (2 OF 2) .657 4.126 PARAMETERS OF CYLINDRICAL INTERPOLATION659 B-64610EN/01 TABLE OF CONTENTS c-5 4.127 PARAMETERS OF OPTIMAL TORQUE ACCELERATION/DECELERATION661 4.128 PARAMETERS OF

46、NANO SMOOTHING663 4.129 PARAMETERS OF TOOL COMPENSATION (3 OF 3).665 4.130 PARAMETERS OF TILTED WORKING PLANE INDEXING (M SERIES) / 3-DIMENSIONAL MANUAL FEED (M SERIES) (2 OF 2)668 4.131 PARAMETERS OF FSSB (2 OF 2) .682 4.132 PARAMETERS OF DISPLAY AND EDIT (6 OF 6)689 4.133 PARAMETERS OF HIGH PRECIS

47、ION OSCILLATION FUNCTION .701 4.134 PARAMETERS OF SPINDLE CONTROL WITH SERVO MOTOR (2 OF 2).703 4.135 PARAMETERS OF GRAPHIC DISPLAY (4 OF 4) 704 APPENDIX APPENDIX A CHARACTER CODE LIST723 B-64610EN/01 1.DISPLAYING PARAMETERS - 1 - 1 DISPLAYING PARAMETERS Follow the procedure below to display paramet

48、ers. 1 Press the function key on the MDI unit as many times as required, or alternatively, press the function key once, then the chapter selection soft key PARAM. The parameter screen is then selected. Function keys 2 The parameter screen consists of multiple pages. Use step (a) or (b) to display th

49、e page that contains the parameter you want to display. (a) Use the page change keys or the cursor keys to display the desired page. (b) Enter the data number of the parameter you want to display from the keyboard, then press the soft key NO.SRH. The parameter page containing the specified data number appears with the cursor positioned at the data number. (The data is displayed in reverse video.) NOTE If key entry is started with the chapter selection soft keys displayed, they are replaced automatically