《PPR管施工方案.docx》由会员分享，可在线阅读，更多相关《PPR管施工方案.docx（9页珍藏版）》请在三一文库上搜索。
1、PPR管施工方案12020 年 4 月 19 日文档仅供参考1.1.1. PPR管道施工工艺 PPR pipe installation method1.1.1.1. 编制依据 Basis of drawing up1.1 给水排水管道工程施工及验收规范GB50268-97。 Constructionandacceptance norm of Water supply anddrains piping engineering。1.2 室 内 管 道 支 架 及 吊 架 03S402 Piping support indoor 。1.1.1.2. 施工工艺： Construction techn
2、ique:根据现场各种管线布置情况和流程顺序确定工艺流程，本工程采用如下工艺流程：施工准备材料进货检验PPR管预制加工支吊架制作安装 PPR 管安装 PPR管试验According to the arrangement and flow order of field allkindsofpipelines,confirmtheprocessflow.Thisengineeringadoptsthefollowingprocessflow:constructionpreparation materialstockingtest PPRpipepre- processing manufacture
3、and installationofsupportand hangerinstallationofPPR pipe PPR pipetest1). 施工准备：Construction preparation施工工作及技术人员认真熟悉原图纸，领会设计意图，对图纸中和实际管道布置清楚后，才能施工。22020 年 4 月 19 日文档仅供参考Constructionworkandtechniciansarestrictlyfamiliarwith the original drawing, comprehend design purpose, andcarryouttheconstructionaf
4、tertheclaritytodrawingand actual pipeline arrangement.施工人员须熟悉PPR 管的一般性能，掌握必须的操作要点。在各项预制加工项目开始前，根据实际编制材料计划，将需要的材料、设备等按规格、型号准备好，运至现场。Constructer must know well the general performance of PPR,masternecessaryoperationpoints,Beforeeachprecastprocessingproject,accordingtotheplanofpracticalscheduling mater
5、ial, well prepare the needed material andequipmentaccordingtospecificationandmodelandtransport to the field.材料设备要求：到现场的管材、管件等提供的管材和管件应符合设计规定，并附有产品说明书和质量合格证书，须认真检查并经业主验明材质，核对质保书，规格、型号等，合格后方能入库，并分别作好标识。Materialequipmentrequirements:The offeredfieldpipeand pipe fittings should accord with design prescr
6、iption,adding with product stipulation and quality certification.Strictly examine and identify material by quality guarantee, specification andowner, modelschecketc,32020 年 4 月 19日文档仅供参考warehouse after qualification, and mark separately.管材和管件的内外壁应光滑平整，无气泡、裂纹、脱皮和明显的痕纹、凹陷，色泽应基本一致。不得使用有损坏迹象的材料。如发现管道质量有
7、异常，应在使用前进行复检。Theinternalandexternalsurfaceofpipeandpipefittings should be smooth and flat, without air bladder,crack,desquamate,obvioustraceandhollow,andthecolor and luster should be consistent. The material withdamaged markshouldbeforbidden.Ifitisdiscoveredthat there is problem in the pipeline qual
8、ity, recheck itbefore using.管材的端面应垂直于管材的轴线。管件应完整、无缺损、无变形。End face of pipe should be upright to the axes of pipe.Thepipefittingsshouldbeintact,withoutlackanddistortion.管件和管材不应长期置于阳光下照射，为避免管子在储运时弯曲，堆放应平整。搬运管材和管件时，应小心轻放，避免油污，严禁剧烈撞击，与尖锐物触碰和抛、摔、拖。管材开口处应及时封堵，以免管道堵塞造成不必要的浪费。Pipefittingandpipeshouldnotbepla
9、cedinthesunshineforalongtimetoavoidthepipecurvein42020 年 4 月 19 日文档仅供参考storage and transportation, and piling up them should be level. When conveying pipe and pipe fittings, they should handled with care and avoid oil stain. Strong bump, cast,throw and draw is forbidden. Pipe hatch should be immedia
10、tely plugged to avoid pipe jam and unnecessary waste.施工现场与材料存放处温差较大时，应于安装前将管件和管材在现场放置一定时间，使其温度接近施工现场环境温度。When there is large difference in construction field and storage temperature, should place pipe fitting at the field before installation for certain make its temperature closure to environmentand
11、 pipetimeandtemperatureof construction field.本项目PPR 管道采用热熔连接，施工前应仔细检查所使用的热熔机具、割刀是否符合要求和正常使用，使用的电源及电线是否正常和安全。如下图：This project pipe-PPR pipe adopts heat fusion. Before construction, should carefully examine whether the usinghot melt equipment and cutter knife accord with requirements and normal servic
12、e, the using power supplyand wire are normal and security. as the following drawings.52020 年 4 月 19 日文档仅供参考材料进货检验：Material-stocking test为确保安装质量，材料进货时应严格检验，其管径椭圆率应10%，管材同一截面的壁厚偏差应14%，内外壁应光滑、平整，无气泡、裂口、裂纹、凹陷、脱皮和严重的冷斑及明显的痕迹。Forinsuringtheinstallationquality,shouldstrictlytest the material when it is stocked. The ellipticity ofpipe diameter should be less than 10%. The wall thicknessdeviationinthesame pipesectionshouldbeless than14%. The internal and external surface should be smooth,flat,withoutairbladder,crack,hollowingdesquamate,severe cold appearance and obvious trace.62020 年 4 月 19 日