《上海贝尔7360 OLT手动开通I240WQ ONU步骤.doc》由会员分享，可在线阅读，更多相关《上海贝尔7360 OLT手动开通I240WQ ONU步骤.doc（5页珍藏版）》请在三一文库上搜索。
1、上海贝尔7360 OLT手动开通ONU步骤1、 通过TL1方式登录OLT，查看是否有新LOID上报至OLT先TELNET上网管telnet 134.207.16.82 用户名：root密码：5520AMSQZ-DX再TELNET上OLT，如10.107.31.6 端口1023telnet 10.107.31.6 1023 /134.207.16.82为OLT的IP地址，后面加1023端口号按一下回车键，弹出以下提示，选TWould you like a TL1 login(T) or TL1 normal session(N) ? N: T 输入帐号密码登录：Enter Username :
2、SUPERUSER /注意：用户名和密码都是大写Enter Password : ANS#150# info configure equipment ont /检索新创的ONU的接口编号configure equipment#-echo equipment#-ontinterface 1/1/1/2/1 sw-ver-pland 3FE53862AOCI76 sernum ALCL:F8AE75F7 subslocid WILDCARD voip-allowed enable log-auth-id 0777444444999999 /检索到新创ONU的接口编号为1/1/1/2/1 admin
3、-state upexitslot 1/1/1/2/1/1 planned-card-type 10_100base plndnumdataports 4 plndnumvoiceports 0exitexit#-leg:isadmin# show interface port ont:1/1/1/2/1 /查看新创ONU的状态=port table=port |admin-status|opr-status-+-+-ont:1/1/1/2/1 up up /注册成功-port count : 1leg:isadmin# show vlan bridge-port-fdb /查看ONU业务是否
4、正常=bridge-port-fdb table=port |vlan-id |mac |fdb-id |status |vmac -+-+-+-+-+-1/1/1/2/1/1/1 41 00:19:c7:e9:24:a6 stacked:2312:0 learned 00:00:00:00:00:001/1/1/2/1/1/1 46 00:19:c7:e9:24:a5 stacked:2312:0 learned 00:00:00:00:00:00 /41和46VLAN都能正常学习到MAC地址，说明业务正常-bridge-port-fdb count : 23、如何查看一块光板配置的SVLA
5、N是多少？telnet 134.207.16.82 /134.207.16.82为OLT的IP地址，无需加端口号用户名：root密码：5520AMSQZ-DX再TELNET上OLT，如10.107.31.6 login: isadmin /注意：用户名和密码都是小写password: ans#150typ:isadmin# info configure service- customer 1 create description Default customer exit ies 1 customer 1 create interface OAM create address 10.107.3
6、1.6/24 sap nt:vp:1:2001 create exit exit no shutdown exit vpls 2 customer 1 v-vpls vlan 2001 create stp shutdown exit sap nt-a:eth:1:0 create exit sap nt-a:xfp:1:2001 create exit no shutdown exit vpls 2601 customer 1 v-vpls vlan 2601 create stp shutdown exit sap nt-a:xfp:1:2601 create exit sap lt:1/
7、1/1:2601 create 1槽位光板的SVLAN为2601 exit no shutdown exit vpls 2602 customer 1 v-vpls vlan 2602 create stp shutdown exit sap nt-a:xfp:1:2602 create exit sap lt:1/1/2:2602 create 2槽位的SVLAN为2602 exit4、 如何查看FTTH配置的业务VLAN是否配置：telnet 134.207.16.82 /134.207.16.82为OLT的IP地址，无需加端口号用户名：root密码：5520AMSQZ-DX再TELNET
8、上OLT，如10.107.31.6 login: isadmin /注意：用户名和密码都是小写password: ans#150typ:isadmin# info configure bridge port 1/1/1/8/1/1/1 （1槽8光口，ONTID=1）configure bridge#-echo bridge#-port 1/1/1/8/1/1/1 max-unicast-mac 16 vlan-id 41 network-vlan stacked:2601:300 vlan-scope local exit vlan-id 45 network-vlan stacked:2601:45 vlan-scope local exit vlan-id 46 network-vlan stacked:2601:46 vlan-scope local exitexit#-typ:isadmin#