《【BS英国标准word原稿】BS EN 1380-2009 Timber structures — Test methods — Load bearing nails, screws, dowels and bolts.doc》由会员分享，可在线阅读，更多相关《【BS英国标准word原稿】BS EN 1380-2009 Timber structures — Test methods — Load bearing nails, screws, dowels and bolts.doc（21页珍藏版）》请在三一文库上搜索。
1、 ，如果你需要更多标准可以到 如果你购买的文档存在缺页、字迹模糊、乱码等情况，请大家通过论坛消息与我联系。BRITISH STANDARDBS EN 1380:2009 ，如果你需要更多标准可以到 如果你购买的文档存在缺页、字迹模糊、乱码等情况，请大家通过论坛消息与我联系。Timber structures Test methods Load bearing nails, screws, dowels and boltsICS 91.080.20NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBS EN
2、 1380:2009National forewordThis British Standard is the UK implementation of EN 1380:2009. It supersedes BS EN 1380:1999 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee B/518, Structural timber.A list of organizations represented on this committee can b
3、e obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under
4、 the authority of the Standards Policy and Strategy Committee on 30 April2009 BSI 2009ISBN 978 0 580 56920 3Amendments/corrigenda issued since publicationDate CommentsBS EN 1380:2009EUROPEAN STANDARD NORME EUROPENNEEUROPISCHE NORMEN 1380April 2009ICS 91.080.20Supersedes EN 1380:1999English VersionTi
5、mber structures - Test methods - Load bearing nails, screws, dowels and boltsStructures en bois - Mthode dessai - Pointes, tire-fonds, broches et boulons porteursHolzbauwerke - Prfverfahren - TragendeNagelverbindungenThis European Standard was approved by CEN on 2 November 2006.CEN members are bound
6、 to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN
7、 Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status
8、 as the official versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, S
9、lovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATION C OM I T EUR OP EN DE NOR M AL I S ATI ON EUR OP I S C HES KOM I TEE F R NOR M UNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CENAll rights of exploitation in any form and by any me
10、ans reserved worldwide for CEN national Members.Ref. No. EN 1380:2009: EContentsPageForeword.31Scope .42Normative references .43Terms and definitions .54Symbols and abbreviations .55Requirements .55.1Timber .55.2Wood-based products .55.3Metal plates and dowel type fasteners .56Test methods.66.1Gener
11、al.66.2Conditioning .66.3Fabrication of the test pieces .66.4Preparation of the test pieces .66.4.1Load parallel to grain .66.4.2Load perpendicular to grain .96.4.3Determination of relative displacements . 146.5Test procedure . 146.6Test results . 146.7Test report . 1415BS EN 1380:2009EN 1380:2009 (
12、E)ForewordThis document (EN 1380:2009) has been prepared by Technical Committee CEN/TC 124 “Timber structures”, the secretariat of which is held by SFS.This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest
13、 by October 2009, and conflicting national standards shall be withdrawn at the latest by October 2009.This document supersedes EN 1380:1999.The first version of this European Standard was published in September 1999 and considered only connections with nails. When the product standard for dowel type
14、 fasteners EN 14592 became available the scope of EN 1380 was expanded. Therefore, this revised version covers dowel type fasteners as nails, screws, dowels and bolts.Connections with load bearing staples are considered in EN 1381:1999.According to the CEN/CENELEC Internal Regulations, the national
15、standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Polan
16、d, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.1ScopeThis European Standard specifies test methods for determining the strength and deformation characteristics of laterally loaded connections with nail, screws, dowels and bolts in load-bearing timber structur
17、es.The methods assess connections with members of timber (solid timber or glued laminated timber) or wood-based products or metal plates (but not punched metal plate fasteners) in the combination proposed for use in service.The methods are used to determine load-slip characteristics and maximum load
18、 of connections where various angles between the applied force and the timber grain direction, or the main direction of the wood-based products, respectively, are possible.2Normative referencesThe following referenced documents are indispensable for the application of this document. For dated refere
19、nces, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.EN 322, Wood-based panels Determination of moisture contentEN 323, Wood-based panels Determination of densityEN 13183-2, Moisture content of a piece of sawn
20、timber Part 2: Estimation by electrical resistance methodEN 14080, Timber structures Glued laminated timber RequirementsEN 14081-1, Timber structures Strength graded structural timber with rectangular cross section Part 1: General requirementsEN 14358, Timber structures Calculation of characteristic
21、 5-percentile values and acceptance criteria for a sampleEN 14592, Timber structures Dowel-type fasteners RequirementsEN 26891:1991, Timber structures Joints made with mechanical fasteners General principles for the determination of strength and deformation characteristics (ISO 6891:1983)EN 28970, T
22、imber structures Testing of joints made with mechanical fasteners Requirements for wood density(ISO 8970:1989)ISO 3131, Wood Determination of density for physical and mechanical tests3Terms and definitionsFor the purposes of this document, the following terms and definitions apply.3.1deformation of
23、the connectionmean value of the measurements of the relative displacements of the members3.2dowel type fastenerselements such as nails, screws, dowels and bolts as defined by EN 145924Symbols and abbreviationsFor the purposes of this document, the following symbols and abbreviations apply.bwidth of
24、member cross-section, in millimetresFload, in newtonstmember thickness, in millimetres5Requirements5.1TimberThe timber (solid timber or glued laminated timber) shall satisfy the requirements of EN 14080, EN 14081-1 and shall be selected in accordance with either of the methods given in EN 28970.For
25、each test piece, the individual members to be joined shall be selected to ensure a test piece of balanced density. For a group of similar test pieces, separate planks shall be used for each test piece.NOTEThe members should be free from major defects, which could lead to premature failure in the are
26、a away from the fasteners.5.2Wood-based productsThe specification of the wood based products shall be established. The products used for the individual members of the test pieces shall be representative of the class or range of product to which they belong and the relevant properties shall be declar
27、ed.One unique grade shall be used to make the test pieces. For each test piece, the individual members in the connection shall be selected from separate pieces of material.5.3Metal plates and dowel type fastenersThe specification of the metal plates shall be established.The requirements for dowel ty
28、pe fasteners as given in EN 14592 apply.6Test methods6.1GeneralThe moisture content and density of the timber or wood-based products members at test shall be determined as specified in EN 13183-2, ISO 3131, EN 322 and EN 323 as appropriate.6.2ConditioningThe test pieces shall be manufactured with th
29、e timber or wood-based products at an equilibrium moisture content corresponding to (20 2) C and (85 5) % relative humidity. The material is conditioned when it attains constant mass. Constant mass is considered to be attained when the results of two successive weightings, carried out at an interval
30、 of 6 h, do not differ by more than 0,1 % of the mass of the material.After manufacture but prior to testing the test pieces shall be stored for at least one week at (20 2) C and (65 5) % relative humidity.For certain investigations other moisture conditioning can be appropriate, and shall be report
31、ed.NOTEFor some hardwoods a much longer storing period can be necessary or the test pieces should be made with appropriate gaps between the members.6.3Fabrication of the test piecesIf there are no special requirements, timber members shall be planed. Test pieces shall be fabricated with the fastener
32、s perpendicular to the member surface. The insertion of the dowel type fasteners shall follow normal preparation (e.g. pre-boring) and practice, which shall be reported. The number of fasteners shall reflect the actual use in practice.In principle the connection is symmetrical with respect to the di
33、rection of the load comprising the geometry of the timber members and number and penetration depth of the fasteners.For nails and screws the depth of the fastener head indentation will have an influence on the test result, particularly for connections loaded in double shear. Therefore, if the fabric
34、ation technique permits the fastener heads shall protrude above the surface.6.4Preparation of the test pieces6.4.1Load parallel to grainFor connections with fasteners that do not pass fully through all members:- consisting solely of timber or wood-based products (or combinations thereof) the test pi
35、eces shall be fabricated either asa) three-member connections with dowel type fasteners from each side, loaded in single shear, seeFigure 1, orb) three-member connections with dowel type fasteners from each side, loaded in double shear, seeFigure 2.The minimum end length l is 50 mm as shown in Figur
36、es 1 and 2 may not be appropriate to thin timber or wood- based products subjected to compression loads.- with metal plates connected with dowel type fasteners to timber or wood-based products members, the test pieces shall be fabricated either asa) single shear test pieces with dowel type fasteners
37、 from each side and with the side members of metal plates, orb) double shear test pieces with dowel type fasteners from each side and with the metal plate as central member.Key1grain direction2not protruding end3protruding end4 displacement pick-up pointslfree lengtht1side member widtht2middle memberNOTEDowels and bolts will usually protrude at the outer faces of the side members.Figure 1 Example of a three timber member connection with not fully penetrating dowel type fasteners loaded in si