《BS EN 12575-1998 塑料.热固模塑复合物.SMC中纤维浸湿程度的测定.pdf》由会员分享，可在线阅读，更多相关《BS EN 12575-1998 塑料.热固模塑复合物.SMC中纤维浸湿程度的测定.pdf（8页珍藏版）》请在三一文库上搜索。
1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 12575:1998 The Euro
2、pean Standard EN 12575:1998 has the status of a British Standard ICS 83.080.10; 83.120 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Plastics Thermoset moulding compounds Determination of the degree of fibre wet out in SMC This British Standard, having been prepared under th
3、e direction of the Sector Board for Materials and Chemicals, was published under the authority of the Standards Board and comes into effect on 15 November 1998 BSI 1998 ISBN 0 580 30020 X BS EN 12575:1998 Amendments issued since publication Amd. No.DateText affected National foreword This British St
4、andard is the English language version of EN 12575:1998. The UK participation in its preparation was entrusted to Technical Committee PRI/42, Fibre reinforced thermosetting plastics and prepregs, which has the responsibility to: aid enquirers to understand the text; present to the responsible Europe
5、an committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cro
6、ss-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled International Standards Correspondence Index, or by using the Find facility of the BSI Standards Electronic C
7、atalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document
8、comprises a front cover, an inside front cover, the EN title page, pages 2 to 5, and a back cover. CEN European Committee for Standardization Comite Europe en de Normalisation Europa isches Komitee fu r Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1998 CEN All rights of exploitat
9、ion in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12575:1998 E EUROPEAN STANDARDEN 12575 NORME EUROPE ENNE EUROPA ISCHE NORM May 1998 ICS 83.120; 83.140.10 Descriptors: Plastics, reinforced plastics, plastic moulding, reinforcing materials, thermosetting resin
10、s, composition: property, tests, determination, rates: per unit time, wetting English version Plastics Thermoset moulding compounds Determination of the degree of fibre wet out in SMC Plastiques Compositions de moulage a base de thermodurcissables De termination du taux de mouillage des fibres dans
11、les SMC Kunststoffe Ha rtbare Formmassen Bestimmung des Faserbenetzungsgrades in SMC This European Standard was approved by CEN on 1 May 1998. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a na
12、tional standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in
13、any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Ger
14、many, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. Page 2 EN 12575:1998 BSI 1998 Foreword This European Standard has been prepared by Technical Committee CEN/TC 249, Plastics, the secretariat of which is held by IBN. This
15、European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 1998, and conflicting national standards shall be withdrawn at the latest by November 1998. According to the CEN/CENELEC Internal Regulations, t
16、he national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kin
17、gdom. Contents Page Foreword2 Introduction3 1Scope3 2Normative references3 3Definitions3 4Sampling3 5Apparatus3 6Procedure3 7Expression of results4 8Test report4 9Precision4 ? Page 3 EN 12575:1998 BSI 1998 Introduction This test method provides a common basis for reinforcement manufacturers, compoun
18、ders and moulders to compare data and follow the consistency of wet out. As wet out often improves during the first 24 h, samples of the same age are used for comparison purposes. In a production situation the process and formulation are assumed to be constant and are sufficient to produce a visual
19、standard level of wet out. Any drifts in paste viscosity, reinforcement fibre content, mass per unit area, compaction structure etc. which adversely affect wet out can be identified. In a development situation the compounding process conditions need to define an acceptable wet out of the control. Fo
20、rmulation or reinforcement specimens can be screened along with the control under identical process conditions. The test is carried out after compounding allowing the products under test to be judged superior or inferior to the control. 1 Scope This European Standard specifies a test method to deter
21、mine the degree of wet out of the reinforcement in a sheet moulding compound (SMC). It is applicable for quality control by the user of the SMC as well as for the process control during the SMC production. 2 Normative references This European Standard incorporates by dated or undated reference, prov
22、isions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it
23、by amendment or revision. For undated references the latest edition of the publication referred to applies. ISO 472, Plastics Vocabulary. ISO 8604, Plastics Prepregs Definitions of terms and symbols for designations. 3 Definitions For the purposes of this standard, the terms and definitions of ISO 4
24、72 and 8604 and the following definitions apply: 3.1 fibre bundle discrete collection of many parallel fibre filaments, chopped or unchopped 3.2 wet out state in which all the reinforcing bundles in the SMC sheet, not necessarily each individual filament, are wet by the paste 4 Sampling From each it
25、em to be controlled (one roll or a sheet of SMC), obtain a laboratory sample consisting of a strip of 40 cm minimum accross the entire width of the SMC sheet. 5 Apparatus Ruler (solvent resistant); Sampling table (approximately 100 cm 3 180 cm). Solvent resistant opaque plate, with a 10 cm 3 10 cm i
26、nspection window (reading field) in its centre. Solvent resistant gloves. Magnifying glass (magnification 10 3). Disposable spatula (such as tongue depressors). 6 Procedure 6.1 Carry out the test immediately after compounding. This procedure can be used as a quality control test at any specified tim
27、e after manufacture. 6.2 Remove the top carrier film from the sample. Use the spatula to split the SMC at different levels of the sheet. This results in a cross section of the SMC sheet in which one can observe the fibres on the top, middle and bottom of the SMC at the same time (see Figure 1). If t
28、he degree of wet out is 100 %, the use of the inspection window is unnecessary. 6.3 If there are dry spots, take a new sample and split it across the entire width along the level containing the most dry areas as previously observed (6.2). Divide the sample into four identical strips of 10 cm length
29、perpendicular to the machine direction and choose the strip which contains the largest dry spots (see Figure 2). 6.4 Inspect the wet out conditions by moving the inspection window in 10 cm steps from left to right. In each 10 cm square (reading field), use the ruler to measure the dimensions of the
30、dry spots to determine the surface area in square centimetres and record the readings. Summarize these readings to achieve the dry spot area of each reading field (Zi). NOTE 1The use of a magnifying glass when necessary, especially in the case of light colours, high filler content and low solubility
31、 sizing of the reinforcing fibres is recommended. NOTE 2Pushing down on the SMC with any object (hands, spatula, knife, elbow etc.) will generally move the paste off the fibres and cause a defect. NOTE 3Should any particular area parallel to the machine direction repeatedly exhibit a defect, the det
32、ermination of the special cause of this defect allows its correction (i.e. wrinkles in film or partial blockage of the doctor blade). ? Page 4 EN 12575:1998 BSI 1998 1) 2) 3) 4) 5) 6) Width Machine direction Top Middle Bottom Level of split Figure 1 1)Chosen strip Figure 2 7 Expression of results De
33、gree of fibre wet out is obtained by the equation: DW= 100 23 100 Zi i = 1 n n 3 A where: DWis the degree of fibre wet out in per cent; nis the number of reading fields; Ziis the total dry spot area of an individual reading field in square centimetres; Ais the surface of the reading field (inspectio
34、n window) in square centimetres 8 Test report The test report shall include the following details: 8.1 Reference to this European Standard. 8.2 Formulation/designation of the SMC. 8.3 Date of production, batch number. 8.4 Number of reading fields of the inspected line (specimen). 8.5 Degree of fibre
35、 wet out (DW). 8.6 Special defect, its exact description and location, i.e. largest single dry spot of the inspected strip with the number of the respective reading field (see Figure 3). For production control purposes the following information shall be added: 8.7 Time between production, sampling a
36、nd testing. 8.8 Temperature of the production room. 8.9 Relative humidity of the production room. 9 Precision The precision of this method is not known because interlaboratory data are not available. When interlaboratory data are obtained, a precision statement will be added with the next revision.
37、? Page 5 EN 12575:1998 BSI 1998 1) 2) Machine direction Largest single spot Strip 2 field 4 L 2/4 Figure 3 ? BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
38、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. I
39、t is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be gratef
40、ul if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service
41、 called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for intern
42、ational standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Tec
43、hnical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and
44、 receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of
45、the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from
46、 BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.