《08-30162845-DC.pdf》由会员分享，可在线阅读，更多相关《08-30162845-DC.pdf（12页珍藏版）》请在三一文库上搜索。
1、a Date: 12 August 2008 Origin: International Latest date for receipt of comments: 30 November 2008 Project no.: 2007/00467 Responsible committee: AUE/15 Safety related to vehicles Interested committees: Title: Draft BS ISO 3780 Road vehicles - World manufacturer identifier (WMI) code Supersession in
2、formation: If this document is published as a standard, the UK implementation of it will supersede BSAU175-2B : 1983 (R03) and partially supersede. NONE If you are aware of a current national standard which may be affected, please notify the secretary (contact details below). WARNING: THIS IS A DRAF
3、T AND MUST NOT BE REGARDED OR USED AS A BRITISH STANDARD. THIS DRAFT IS NOT CURRENT BEYOND 30 November 2008. This draft is issued to allow comments from interested parties; all comments will be given consideration prior to publication. No acknowledgement will normally be sent. See overleaf for infor
4、mation on commenting. No copying is allowed, in any form, without prior written permission from BSI except as permitted under the Copyright, Designs and Patent Act 1988 or for circulation within a nominating organization for briefing purposes. Electronic circulation is limited to dissemination by e-
5、mail within such an organization by committee members. Further copies of this draft may be purchased from BSI Customer Services, Tel: +44(0) 20 8996 9001 or email . British, International and foreign standards are also available from BSI Customer Services. Information on the co-operating organizatio
6、ns represented on the committees referenced above may be obtained from the responsible committee secretary. Cross-references The British Standards which implement International or European publications referred to in this draft may be found via the British Standards Online Service on the BSI web sit
7、e http:/. Direct tel: 020 8996 7009 Responsible Committee Secretary: Committee Service Centre (BSI) E-mail: Draft for Public Comment Head Office 389 Chiswick High Road London W4 4AL Telephone: +44(0)20 8996 9000 Fax: +44(0)20 8996 7001 Form 36 Version 8.0 DPC: 08/30162845 DC Licensed CopyChinese Un
8、iversity of Hong Kong, 21/10/2008 07:23, Uncontrolled Copy, (c) BSI b Introduction This draft standard is based on international discussions in which the UK has taken an active part. Your comments on this draft are invited and will assist in the preparation of the consequent standard. Comments submi
9、tted will be reviewed by the relevant BSI committee before sending the consensus UK vote and comments to the international secretariat, which will then decide appropriate action on the draft and the comments received. If no comments are received to the contrary, then the UK will approve this draft.
10、If the international standard is approved, it is possible the text will be published as an identical British Standard. UK Vote Please indicate whether you consider the UK should submit a negative (with reasons) or positive vote on this draft. Submission The guidance given below is intended to ensure
11、 that all comments receive efficient and appropriate attention by the responsible BSI committee. Annotated drafts are not acceptable and will be rejected. All comments must be submitted, preferably electronically, to the Responsible Committee Secretary at the address given on the front cover. Commen
12、ts should be compatible with Version 6.0 or Version 97 of Microsoft Word for Windows, if possible; otherwise comments in ASCII text format are acceptable. Any comments not submitted electronically should still adhere to these format requirements. All comments submitted should be presented as given i
13、n the example below. Further information on submitting comments and how to obtain a blank electronic version of a comment form are available from the BSI web site at: http:/ Template for comments and secretariat observations Date: xx/xx/200x Document: ISO/DIS xxxxx 1 2 (3) 4 5 (6) (7) MB Clause No./
14、 Subclause No./ Annex (e.g. 3.1) Paragraph/ Figure/Table/ Note (e.g. Table 1) Type of com- ment Comment (justification for change) by the MB Proposed change by the MB Secretariat observations on each comment submitted 3.1 Definition 1 ed Definition is ambiguous and needs clarifying. Amend to read .
15、so that the mains connector to which no connection . 6.4 Paragraph 2 te The use of the UV photometer as an alternative cannot be supported as serious problems have been encountered in its use in the UK. Delete reference to UV photometer. Microsoft and MS-DOS are registered trademarks, and Windows is
16、 a trademark of Microsoft Corporation. Licensed CopyChinese University of Hong Kong, 21/10/2008 07:23, Uncontrolled Copy, (c) BSI THIS DOCUMENT IS A DRAFT CIRCULATED FOR COMMENT AND APPROVAL. IT IS THEREFORE SUBJECT TO CHANGE AND MAY NOT BE REFERRED TO AS AN INTERNATIONAL STANDARD UNTIL PUBLISHED AS
17、 SUCH. IN ADDITION TO THEIR EVALUATION AS BEING ACCEPTABLE FOR INDUSTRIAL, TECHNOLOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL TO BECOME STANDARDS TO WHICH REFERENCE MAY BE MADE IN NATIONAL REGULATIONS. RECI
18、PIENTS OF THIS DRAFT ARE INVITED TO SUBMIT, WITH THEIR COMMENTS, NOTIFICATION OF ANY RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE AND TO PROVIDE SUPPORTING DOCUMENTATION. DRAFT INTERNATIONAL STANDARD ISO/DIS 3780 International Organization for Standardization, 2008 INTERNATIONAL ORGANIZATION FOR S
19、TANDARDIZATION ORGANISATION INTERNATIONALE DE NORMALISATION ISO/TC 22 Voting begins on: 2008-08-04 Secretariat: AFNOR Voting terminates on: 2009-01-04 Road vehicles World manufacturer identifier (WMI) code Vhicules routiers Code didentification mondiale des constructeurs (WMI) Revision of second edi
20、tion (ISO 3780:1983) ICS 43.020 To expedite distribution, this document is circulated as received from the committee secretariat. ISO Central Secretariat work of editing and text composition will be undertaken at publication stage. Pour acclrer la distribution, le prsent document est distribu tel qu
21、il est parvenu du secrtariat du comit. Le travail de rdaction et de composition de texte sera effectu au Secrtariat central de lISO au stade de publication. Licensed CopyChinese University of Hong Kong, 21/10/2008 07:23, Uncontrolled Copy, (c) BSI ISO/DIS 3780 ii ISO 2008 All rights reserved PDF dis
22、claimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties
23、 accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to
24、the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. Copyright not
25、ice This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as permitted under the applicable laws of the users country, neither this ISO draft nor any extract from it may be reproduced, stored in a retrieval system or transmitted in any form or by any means, el
26、ectronic, photocopying, recording or otherwise, without prior written permission being secured. Requests for permission to reproduce should be addressed to either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel.
27、 + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Reproduction may be subject to royalty payments or a licensing agreement. Violators may be prosecuted. Licensed CopyChinese University of Hong Kong, 21/10/2008 07:23, Uncontrolled Copy, (c) BSI ISO/DIS 3780 ISO 2008 All
28、 rights reserved iii Contents Page Foreword iv Introductioniv 1 Scope1 2 Normative references1 3 Definition1 4 General characteristics.1 5 Specific characteristics 2 Annex A (normative) WMI country code distribution3 Licensed CopyChinese University of Hong Kong, 21/10/2008 07:23, Uncontrolled Copy,
29、(c) BSI ISO/DIS 3780 iv ISO 2008 All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. E
30、ach member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the Internati
31、onal Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standa
32、rds adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject
33、 of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 3780 was prepared by Technical Committee ISO/TC 22, Road vehicles. Licensed CopyChinese University of Hong Kong, 21/10/2008 07:23, Uncontrolled Copy, (c) BSI ISO/DIS 3780 ISO 2008 All rights reser
34、ved v Introduction Essential modification compared to the 1983 edition: The original WMI country code distribution was established over 25 years ago and much has happened in that time frame. Since publication of the current edition of ISO 3780 in 1983, some countries no longer exist; other countries
35、 have rapidly increasing automotive industries (i.e. China) and are rapidly depleting their original WMI allocations. Other countries that have been allocated many WMIs have no major automotive industry and their allocation of WMIs have gone unused. To address this issue before the situation gets cr
36、itical, SAE, the International Agency for maintenance of the WMI codes and the SAE VIN/WMI Committee updated and adjusted the WMI country code matrix. Annex A of this draft contains the amended WMI table. Clause 4.3 was amended to reduce the possibility of different interpretations of that chapter.
37、In addition, the document was editorially revised. Licensed CopyChinese University of Hong Kong, 21/10/2008 07:23, Uncontrolled Copy, (c) BSI Licensed CopyChinese University of Hong Kong, 21/10/2008 07:23, Uncontrolled Copy, (c) BSI ISO/DIS 3780 1 ISO 2008 All rights reserved Road vehicles World man
38、ufacturer identifier (WMI) code 1 Scope The present document specifies the content and structure of an identifier in order to establish, on a world-wide basis, the identification of road vehicle manufacturers. This identifier (WMI) is the first section of the vehicle identification number (VIN) desc
39、ribed in ISO 3779. It applies to motor vehicles, towed vehicles, motorcycles and mopeds as defined in ISO 3833. 2 Normative references The following referenced documents are indispensable for the application of this document. For undated references, the latest edition of the referenced document (inc
40、luding any amendments) applies. ISO 3779, Road vehicles - Vehicle identification number (VIN) - Content and structure ISO 3833, Road vehicles - Types - Terms and definitions 3 Terms and definitions For the purposes of this document, the following term and definition apply. 3.1 world manufacturer ide
41、ntifier WMI the first section of the vehicle identification number (VIN), designating the manufacturer of the vehicle, assigned to a vehicle manufacturer in order to allow identification of the said manufacturer, and, when used in conjunction with the remaining sections of the VIN, ensures uniquenes
42、s of the VIN for all vehicles manufactured in the world for a period of 30 years 4 General characteristics 4.1 The WMI code shall consist of three characters. Only the following arabic numerals and capital roman letters shall be used in the VIN: 1 2 3 4 5 6 7 8 9 0 A B C D E F G H J K L M N P R S T
43、U V W X Y Z The letters I, O and Q shall not be used. 4.2 The assigned WMI codes will be maintained and checked by the International Agency acting under authorization from ISO: the Society of Automotive Engineers, Inc. (SAE), 400 Commonwealth Drive, Warrendale, PA 15096-0001, USA. Licensed CopyChine
44、se University of Hong Kong, 21/10/2008 07:23, Uncontrolled Copy, (c) BSI ISO/DIS 3780 2 ISO 2008 All rights reserved 4.3 One or more WMI codes will be assigned to each manufacturer responsible for production of vehicles as specified in ISO 3779 by the National Organization of that country in which t
45、he manufacturer has his headquarters. The manufacturer may delegate the responsibility for the production of the vehicles to a subsidiary company. 4.4 A WMI code assigned to a manufacturer must not be assigned to another manufacturer for at least 30 years after the last year in which the code was us
46、ed. 5 Specific characteristics 5.1 First position An alphabetic or numeric character designating a geographic area. More than one character may be assigned to a geographic area, based on anticipated needs. The global allocation of the first position is specified in Annex A. 5.2 Second position An al
47、phabetic or numeric character designating a country within a specific geographic area. More than one character may be assigned to a country, based on anticipated needs. It is necessary to use a combination of the first and second characters to ensure unique identification of the country. The global
48、allocation of the second position is specified in Annex A. 5.3 Assignments of the first and second position The combination(s) of the first and second position shall be assigned to each country by the International Agency in compliance with Annex A. 5.4 Third position 5.4.1 An alphabetic or numeric
49、character assigned by the National Organization to designate a specific manufacturer. It is necessary to use a combination of the first, second and third characters to ensure unique identification of the manufacturer. Note More than one combination of characters (i.e. more than one WMI code) may be assigned to a manufacturer, based on specific needs. 5.4.2 The n