《BS-EN-1870-14-2007.pdf》由会员分享，可在线阅读，更多相关《BS-EN-1870-14-2007.pdf（60页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 1870-14:2007 Safety of woodworking machines Circular sawing machines Part 14: Vertical panel sawing machines ICS 79.120.10 ? Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2
2、008 20:21:58 MDTNo reproduction or networking permitted without license from IHS -,-,- BS EN 1870-14:2007 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 March 2008 BSI 2008 ISBN 978 0 580 56957 9 National foreword This British Standard is
3、 the UK implementation of EN 1870-14:2007. Together with BS EN 1870-13:2007 it supersedes BS EN 1870-2:1999 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee MTE/23, Woodworking machines. A list of organizations represented on this committee can be obta
4、ined on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Amendments/corrigenda issued since publicati
5、on DateComments Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 20:21:58 MDTNo reproduction or networking permitted without license from IHS -,-,- EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE
6、NORM EN 1870-14 December 2007 ICS 79.120.10Supersedes EN 1870-2:1999 English Version Safety of woodworking machines - Circular sawing machines - Part 14: Vertical panel sawing machines Scurit des machines pour le travail du bois - Machines scies circulaires - Partie 14: Scies panneaux verticales Sic
7、herheit von Holzbearbeitungsmaschinen - Kreissgemaschinen - Teil 14: Vertikalplattenkreissgemaschinen This European Standard was approved by CEN on 22 November 2007. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Stan
8、dard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, Frenc
9、h, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus,
10、Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT
11、EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2007 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1870-14:2007: E Copyright British Standards Institution Provided by
12、IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 20:21:58 MDTNo reproduction or networking permitted without license from IHS -,-,- EN 1870-14:2007 (E) 2 Contents Page Foreword4 Introduction.6 1 Scope 6 2 Normative references7 3 Terms and defini
13、tions .9 4 List of significant hazards 13 5 Safety requirements and / or measures 16 5.1 General16 5.2 Controls 16 5.2.1 Safety and reliability of control systems.16 5.2.2 Position of controls.17 5.2.3 Starting .17 5.2.4 Normal stopping 18 5.2.5 Emergency stop.19 5.2.6 Cutting cycle on vertical pane
14、l sawing machines with integrated feed.20 5.2.7 Speed changing.21 5.2.8 Failure of the power supply21 5.2.9 Failure of the control circuits.22 5.3 Protection against mechanical hazards22 5.3.1 Stability.22 5.3.2 Hazard resulting from break-up during operation22 5.3.3 Tool holder and tool design23 5.
15、3.4 Braking23 5.3.5 Devices to minimise the possibility or the effect of ejection24 5.3.6 Work piece supports and guides.28 5.3.7 Prevention of access to moving parts.30 5.3.8 Guarding of drives.33 5.4 Protection against non-mechanical hazards 33 5.4.1 Fire 33 5.4.2 Noise .33 5.4.3 Emission of chips
16、 and dust34 5.4.4 Electricity35 5.4.5 Ergonomics and handling.36 5.4.6 Pneumatics.36 5.4.7 Electromagnetic compatibility36 5.4.8 Static electricity .37 5.4.9 Errors of fitting.37 5.4.10 Supply disconnection (isolation).37 5.4.11 Maintenance.37 6 Information for use38 6.1 Warning devices 38 6.2 Marki
17、ng.38 6.2.1 Marking of the machine.38 6.2.2 Marking of riving knives and pressure shoes 39 6.3 Instruction handbook39 Annex A (informative) Use of well tried components42 BS EN 1870-14:2007 Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Bo
18、eing Co/5910770001 Not for Resale, 08/14/2008 20:21:58 MDTNo reproduction or networking permitted without license from IHS -,-,- EN 1870-14:2007 (E) 3 Annex B (normative) Impact test method for guards43 B.1 General .43 B.2 Test method .43 B.2.1 Preliminary remarks43 B.2.2 Testing equipment.43 B.2.3
19、Projectile for guards43 B.2.4 Sampling.43 B.2.5 Test procedure.43 B.3 Results44 B.4 Assessment .44 B.5 Test report44 B.6 Test equipment for impact test44 Annex C (normative) Saw spindle dimensional tolerances46 Annex D (normative) Riving knife mounting strength test.47 Annex E (normative) Riving kni
20、fe testing - Lateral stability.48 Annex F (normative) Braking tests .49 F.1 Conditions for all tests49 F.2 Tests .49 F.2.1 Un-braked run-down time.49 F.2.2 Braked run-down time.49 Annex G (normative) Use of electronic components50 G.1 General .50 G.2 SRECS design50 G.2.1 Components, hardware.50 G.2.
21、2 Safety related software.51 Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 98/37/EC53 Bibliography56 BS EN 1870-14:2007 Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boei
22、ng Co/5910770001 Not for Resale, 08/14/2008 20:21:58 MDTNo reproduction or networking permitted without license from IHS -,-,- EN 1870-14:2007 (E) 4 Foreword This document (EN 1870-14:2007) has been prepared by Technical Committee CEN/TC 142 “Woodworking machines - Safety”, the secretariat of which
23、is held by UNI. This document shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2008 and conflicting national standards shall be withdrawn at the latest by June 2009. This document together with EN 1870-13:2007 super
24、sedes EN 1870-2:1999. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of the Machinery Directive. For relationship with EU Directive, see informative Annex ZA, which is an integral pa
25、rt of this document. Organisations contributing to the preparation of this European Standard include the European Committee of Woodworking Machinery Manufacturers Association “EUMABOIS“. The European Standards produced by CEN/TC 142 are particular to woodworking machines and complement the relevant
26、A and B Standards on the subject of general safety (see introduction of EN ISO 12100-1:2003 for a description of A, B and C standards). EN 1870 Safety of woodworking machines Circular sawing machines consists of the following parts: Part 1: Circular saw benches (with and without sliding table), dime
27、nsion saws and building site saws Part 2: Horizontal beam panel saws and vertical panel saws Part 3: Down cutting cross-cut saws and dual purpose down cutting cross-cut saws/circular saw benches Part 4: Multiblade rip sawing machines with manual loading and/or unloading Part 5: Circular saw benches/
28、up-cutting cross-cut sawing machines Part 6: Circular sawing machines for firewood and dual purpose circular sawing machines for firewood/circular saw benches, with manual loading and/or unloading Part 7: Single blade log sawing machines with integrated feed table and manual loading and/or unloading
29、 Part 8: Single blade edging circular rip sawing machines with power driven saw unit and manual loading and/or unloading Part 9: Double blade circular sawing machines for cross-cutting with integrated feed and with manual loading and/or unloading Part 10: Single blade automatic and semi-automatic up
30、-cutting cross-cut sawing machines Part 11: Semi-automatic and automatic horizontal cross-cut sawing machines with one saw unit (radial arm saws) Part 12: Pendulum cross-cut sawing machines Part 13: Horizontal beam panel sawing machines BS EN 1870-14:2007 Copyright British Standards Institution Prov
31、ided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 20:21:58 MDTNo reproduction or networking permitted without license from IHS -,-,- EN 1870-14:2007 (E) 5 Part 14: Vertical panel sawing machines Part 15: Multiblade cross-cut sawing machin
32、es with integrated feed of the workpiece and manual loading and/or unloading Part 16: Double mitre sawing machines for V-cutting Part 17: Manual horizontal cutting cross-cut sawing machines with one saw unit (manual radial arm saws) According to the CEN/CENELEC Internal Regulations, the national sta
33、ndards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
34、Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. BS EN 1870-14:2007 Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 20:21:58 MDTNo reproduction or networki
35、ng permitted without license from IHS -,-,- EN 1870-14:2007 (E) 6 Introduction This document has been prepared to be a harmonised standard to provide one means of conforming to the essential safety requirements of the Machinery Directive, and associated EFTA regulations. This document is a type C st
36、andard as defined in EN ISO 12100-1:2003. The machinery concerned and the extent to which hazards, hazardous situations and events covered are indicated in the scope of this document. When provisions of this type C standard are different from those which are stated in type A or B standards, the prov
37、isions of this type C standard take precedence over the provisions of other standards, for machines that have been designed and built according to the provisions of this type C standard. The requirements of this document are directed to manufacturers and their authorised representatives of vertical
38、panel sawing machines. This document is also useful for designers and importers. This document also includes provision and examples of information to be provided by the manufacturer to the user. Common requirements for tooling are given in EN 847-1:2005+A1:2007. 1 Scope This document deals with the
39、significant hazards, hazardous situations and events as listed in Clause 4 which are relevant to manually loaded and unloaded vertical panel sawing (with or without integrated feed) machines fitted with: the facility for scoring; an angle cutting device; a middle support device; a programmable stop
40、for parallel vertical cuts; the facility for grooving with a width of at most 20 mm in one pass by using a milling tools, hereinafter referred to as “machines“ when they are used as intended and under the conditions foreseen by the manufacturer. The machines are designed for cutting panels of the fo
41、llowing materials: a) wood based materials such as chipboard, fibreboard, plywood and also these materials where they are covered with plastic / light alloy laminates; b) solid wood; c) hardened rubber and hardened plastic material; d) non ferrous materials e.g. light alloy; BS EN 1870-14:2007 Copyr
42、ight British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 20:21:58 MDTNo reproduction or networking permitted without license from IHS -,-,- EN 1870-14:2007 (E) 7 e) compound materials with core consisting o
43、f polyurethane or mineral material laminated with light alloy. This document does not apply to vertical panel saws with pressure beam and saw unit mounted behind the workpiece support. This document does not deal with hazards relating to the combination of a single machine being used with any other
44、machine (as part of a line). This document is not applicable to vertical panel saws which are manufactured before the date of its publication as EN. NOTE Machines covered by this standard are listed under A.1.4 of annex IV of the Machinery Directive. 2 Normative references The following referenced d
45、ocuments are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 294:1992, Safety of machinery Safety distances to prevent danger zones b
46、eing reached by the upper limbs EN 847-1:2005+A1:2007, Tools for woodworking Safety requirements Part 1: Milling tools, circular saw blades EN 894-1:1997, Safety of machinery Ergonomics requirements for the design of display and control actuators Part 1: General principles for human interactions wit
47、h displays and control actuators EN 894-2:1997, Safety of machinery Ergonomics requirements for the design of display and control actuators Part 2: Displays EN 894-3:2000, Safety of machinery Ergonomics requirements for the design of display and control actuators Part 3: Control actuators EN 983:199
48、6, Safety of machinery Safety requirements for fluid power systems and their components Pneumatics EN 1005-1:2001, Safety of machinery Human physical performance Part 1: Terms and definitions EN 1005-2:2003, Safety of machinery Human physical performance Part 2: Manual handling of objects associated to machinery EN 1005-3:2002, Safety of machinery Human physical performance Part 3: Recommended fo