《BS-EN-2515-1990.pdf》由会员分享，可在线阅读，更多相关《BS-EN-2515-1990.pdf（12页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD AEROSPACE SERIES BS EN 2515:1990 Specification for Rod ends, adjustable single fork and threaded shank Dimensions and loads This European Standard EN 2515 has the status of a British Standard. Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 02:05:55 GMT+00:00 2006, Uncontroll
2、ed Copy, (c) BSI BS EN 2515:1990 This British Standard was published under the authority of the Board of BSI and comes into effect on 31 December 1990 BSI 12-1999 The following BSI references relate to the work on this standard: Committee reference ACE/14 Draft for comment 89/79499 DC ISBN 0 580 190
3、70 6 Cooperating organizations The European Committee for Standardization, under whose supervision this European Standard was prepared, comprises the national standards organizations of the following Western European countries. AustriaOesterreichisches Normungsinstitut BelgiumInstitut belge de norma
4、lisation DenmarkDansk Standardiseringsraad FinlandSuomen Standardisoimisliito, r.y. FranceAssociation franaise de normalisation GermanyDeutsches Institut fr Normung e.V. GreeceHellenic Organization for Standardization IcelandTechnological Institute of Iceland IrelandNational Standards Authority of I
5、reland ItalyEnte Nazionale Italiano di Unificazione LuxemburgInspection du Travail et des Mines NetherlandsNederlands Normalisatie-instituut NorwayNorges Standardiseringsforbund PortugalInstituto Portugus de Qualidade SpainAsociacin Espaola de Normalizacin y Certificacin SwedenStandardiseringskommis
6、sionen i Sverige SwitzerlandAssociation suisse de normalisation United KingdomBritish Standards Institution Amendments issued since publication Amd. No.Date of issueComments Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 02:05:55 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 2515:1990 BSI
7、 12-1999i Contents Page Cooperating organizationsInside front cover National forewordii Brief history2 Text of EN 25153 National appendix AInside back cover National appendix BInside back cover Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 02:05:55 GMT+00:00 2006, Uncontrolled Copy, (c) BSI
8、 BS EN 2515:1990 ii BSI 12-1999 National foreword This British Standard has been prepared under the direction of the Aerospace Standards Policy Committee and is the English language version of EN 2515 “Aerospace series. Rod ends, adjustable single fork and threaded shank. Dimensions and loads”, publ
9、ished by the European Committee for Standardization (CEN). EN 2515 was produced as a result of international discussion in which the UK took an active part. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their
10、 correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 6, an inside back cover and a back cover. This standard has
11、 been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 02:05:55 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCH
12、E NORM EN 2515 June 1990 UDC: 629.7.02:621.827.1:621.85.053.004.1 Key words: Aircraft industry, flight control, rod ends, threated ends, dimensions, static loads English version Aerospace series Rod ends, adjustable single fork and threaded shank Dimensions and loads Srie arospatiale Embouts rglable
13、s chape simple et tige filete Dimensions et charges Luft- und Raumfahrt Einstellbare Gabelkpfe einfach, mit Gewindeschaft Mae und Belastungen This European Standard was accepted by CEN on 1990-01-10. CEN members are bound to comply with the requirements of CEN Internal Regulations which stipulate th
14、e conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Central Secretariat or to any CEN member. This European Standard exist
15、s in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to CEN Central Secretariat has the same status as the official versions. CEN members are the national standards orga
16、nizations of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxemburg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central
17、 Secretariat: rue de Stassart 36, B-1050 Brussels CEN 1990 Copyright reserved to all CEN members Ref. No. EN 2515:1990 E Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 02:05:55 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 2515:1990 BSI 12-1999 2 Brief history This European Standard has been
18、 prepared by the European Association of Aerospace Manufacturers (AECMA). After inquiries and votes carried out in accordance with the rules of this Association, this Standard has successively received the approval of the National Associations and the Official Services of the member countries of AEC
19、MA, prior to its presentation to CEN. According to the Common CEN/CENELEC Rules, the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Swit
20、zerland and United Kingdom. Contents Page Brief history2 1Scope and field of application3 2References3 3Required characteristics3 4Designation6 5Marking6 6Technical specification6 Figure4 Table5 Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 02:05:55 GMT+00:00 2006, Uncontrolled Copy, (c) BS
21、I EN 2515:1990 BSI 12-19993 1 Scope and field of application This standard specifies the characteristics of adjustable rod ends consisting of a rod end body with threaded shank consisting of: a single fork; a circumferential groove to identify location; an optional longitudinal groove for locking pu
22、rposes. These rod ends are intended for flight control rods or rods for aerospace structures. The cadmium plating restricts the application to temperature not exceeding 235 C. 2 References ISO 3353, Aerospace construction Rolled threads Runout and lead threads. ISO 5855-1, Aerospace MJ Threads Part
23、1: General requirements. ISO 5855-2, Aerospace MJ Threads Part 2: Limit dimensions for bolts and nuts. EN 2133, Cadmium plating of steels with maximum specified tensile strength equal to or less than 1450 MPa, and copper and copper alloys Aerospace series1). EN 2137, Steel FE-PL75 1 100 MPa u Rm u 1
24、 250 MPa Bars Deu 100 mm Aerospace series1). EN 2438, Steel FE-PL62 900 MPa u Rmu 1 100 MPa Bars De u 40 mm Aerospace series1). EN 2601, Aerospace series Fork ends Technical specification2). EN 2791, Aerospace series Rod ends, adjustable single fork and threaded shank Dimensions and loads3). 3 Requi
25、red characteristics 3.1 Dimensions Tolerances Configuration: See Figure. Dimensions and tolerances: See Figure and Table, values after cadmium plating. 3.2 Surface See Figure, values before cadmium plating. 3.3 Materials Steel EN 2137 or EN 2438. 1) Published as AECMA standard. 2) In preparation. 3)
26、 Published as AECMA pre-standard. Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 02:05:55 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 2515:1990 4 BSI 12-1999 3.4 Surface treatment Cadmium plating, except on the bore C: EN 2133, 7 m to 20 m except thread 5 m to 10 m NOTEThe circumferential
27、groove and the longitudinal groove under distance M, shall be painted red. Figure Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 02:05:55 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 2515:1990 BSI 12-19995 Table Dimensions in millimetres ForkThreadRod end Size Code ABCDEFGHJK Thread designa
28、tiona LMbNPRSTVUltimate load kN Mass . g J7 0,25 0,25 0,1 0.25min.max. Vc1420,2612,0 3019,5240,5213MJ 10 1,25 4h6h 39222,48,0 0,8334054 Wc1522,2813,9 3621,5300,8215MJ 12 1,25 4h6h 44252,410,2 0,8385881 Y2028,2 1017,8 4127,0340,8317MJ 14 1,5 4h6h50313,212,2 1,04044483132 a Thread: According to ISO 58
29、55-1 and ISO 5855-2 rolled. b M: Minimum length of engaged threads, includes thickness of lock washers and height of nut. c The codes V and W shall not be used for new design (see EN 2791). + 0,1 0 + 0,2 0 + 0,2 0 + 1 0 + 1 0 + 0,1 0 0 0,1 0 1 0 0, 25 Licensed Copy: sheffieldun sheffieldun, na, Fri
30、Nov 03 02:05:55 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 2515:1990 6 BSI 12-1999 4 Designation Each adjustable single fork rod end fitting shall only be designated as in the following example: With application of the following codes: NOTEIf necessary, the originator code I9005 may be introduced
31、 between the description block and identity block. 5 Marking In addition to the manufacturers own marking, each rod end (see Figure) and the package shall be marked, using the identity block specified in clause 4 of this standard. 6 Technical specification Rod ends supplied according to this standar
32、d shall conform with the requirements of EN 2601. L= left hand thread R= right hand thread Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 02:05:55 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 2515:1990 BSI 12-1999 National appendix A The United Kingdom participation in the preparation of
33、 this European Standard was entrusted by the Aerospace Standards Policy Committee (ACE/-) to Technical Committee ACE/14 upon which the following bodies were represented: British Independent Steel Producers Association Civil Aviation Authority (Airworthiness Division) Federation of Wire Rope Manufact
34、urers of Great Britain Institute of Petroleum Ministry of Defence Society of British Aerospace Companies Ltd. Stainless Steel Wire Industry Association National appendix B The British Standards corresponding to the European Standards and International Standards referred to in the text are identical
35、in number and title as those given in clause 2 with the exception of ISO 3353, ISO 5855-1 and ISO 5855-2 for which the corresponding British Standards are British Standard A 231 (identical); BS 6293-1 (identical) and BS 6293-2 (identical) respectively. Licensed Copy: sheffieldun sheffieldun, na, Fri
36、 Nov 03 02:05:55 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 2515:1990 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the internati
37、onal level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We wo
38、uld be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual upd
39、ating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orde
40、rs for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Librar
41、y and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards dev
42、elopments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the pub
43、lications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written pe
44、rmission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070. Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 02:05:55 GMT+00:00 2006, Uncontrolled Copy, (c) BSI