《BS-EN-2591-219-2002.pdf》由会员分享，可在线阅读，更多相关《BS-EN-2591-219-2002.pdf（6页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD AEROSPACE SERIES BS EN 2591-219:2002 Elements of electrical and optical connection Test methods Part 219: Voltage strength for insulated terminal lugs and in-line splices The European Standard EN 2591-219:2002 has the status of a British Standard ICS 49.060 NO COPYING WITHOUT BSI PE
2、RMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Licensed Copy: sheffieldun sheffieldun, na, Thu Nov 02 18:11:41 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 2591-219:2002 This British Standard, having been prepared under the direction of the Engineering Sector Policy and Strategy Committee, was pu
3、blished under the authority of the Standards Policy and Strategy Committee on 3 July 2002 BSI 3 July 2002 ISBN 0 580 39951 6 National foreword This British Standard is the official English language version of EN 2591-219:2002. The UK participation in its preparation was entrusted by Technical Commit
4、tee ACE/6, Aerospace avionic electrical and fibre optic technology, to Subcommittee ACE/6/3, Aerospace Connectors, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which imple
5、ment international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purpo
6、rt to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible European
7、committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2
8、 and 3 and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. DateComments Licensed Copy: sheffieldun sheffieldun, na, Thu Nov 02 18:11:41 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDA
9、RD NORME EUROPENNE EUROPISCHE NORM EN 2591-219 June 2002 ICS 49.060 English version Aerospace series - Elements of electrical and optical connection - Test methods - Part 219: Voltage strength for insulated terminal lugs and in-line splices Srie arospatiale - Organes de connexion lectrique et optiqu
10、e - Mthodes dessais - Partie 219: Tenue en tension des cosses et des prolongateurs isols Luft- und Raumfahrt - Elektrische und optische Verbindungselemente - Prfverfahren - Teil 219: Spannungsfestigkeit fr Kabelschhe und Stoverbinder mit Isolierhulse This European Standard was approved by CEN on 8 F
11、ebruary 2002. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be
12、 obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Managemen
13、t Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdo
14、m. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2002 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 2591-219:2002 E Lice
15、nsed Copy: sheffieldun sheffieldun, na, Thu Nov 02 18:11:41 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 2591-219:2002 (E) 2 Foreword This document (EN 2591-219:2002) has been prepared by the European Association of Aerospace Manufacturers (AECMA). After enquiries and votes carried out in accordanc
16、e with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of a
17、n identical text or by endorsement, at the latest by December 2002, and conflicting national standards shall be withdrawn at the latest by December 2002. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this Eur
18、opean Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom Licensed Copy: sheffieldun sheffieldun, na, Thu Nov 02 18:11:41 GMT+00:00 2006, Un
19、controlled Copy, (c) BSI EN 2591-219:2002 (E) 3 1Scope This standard specifies a method for checking the voltage strength of insulated terminal lugs and in-line splices. It shall be used together with EN 2591-100. 2Normative references This European Standard incorporates by dated or undated referenc
20、e, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated
21、 in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 2591-100Aerospace series Elements of electrical and optical connection Test methods Part 100: General 1) 3Preparation of specimens The specimens shall be fitted with their normal acc
22、essories, and wired up in accordance with the technical specification. The following details shall be specified in the technical specification: number of specimens; type of cable; installation and wiring of specimens; voltage strength. Terminal lugs To facilitate the test, the spade end may be cut f
23、lush with the insulator and this end is insulated by covering with beeswax or some other watertight material, making sure that this covering does not cover the area of the barrel deformed by the crimping tool. In-line splices The shortest cable shall be cut flush with the insulator of the in-line sp
24、lice. This end shall be insulated by coating in the same way as outlined above. 4Method The crimped component shall be immersed in an aqueous solution containing 5 % sodium chloride to a depth that allows the crimped area to be covered. Apply a voltage between the specimen and an immersed electrode
25、situated a maximum of 50 mm from the specimen. This voltage shall be increased gradually, without exceeding 500 V/s, to 1 500 V, 50 Hz or to the voltage strength specified in the technical specification; it is then kept at this value for a minimum of 60 s. 5Requirement There shall be no burn-out of
26、the insulation. 1) Published as AECMA Prestandard at the date of publication of this standard Licensed Copy: sheffieldun sheffieldun, na, Thu Nov 02 18:11:41 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 2591-219:2002 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI
27、is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make s
28、ure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee respon
29、sible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for al
30、l BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI p
31、olicy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Servi
32、ce. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and
33、receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Onlin
34、e can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under
35、the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implemen
36、ting the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-. Licensed Copy: sheffieldun sheffieldun, na, Thu Nov 02 18:11:41 GMT+00:00 2006, Uncontrolled Copy, (c) BSI