《BS-EN-170100-2001.pdf》由会员分享，可在线阅读，更多相关《BS-EN-170100-2001.pdf（22页珍藏版）》请在三一文库上搜索。
1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 170100:2001 The Eur
2、opean Standard EN 170100:2001 has the status of a British Standard ICS 31.140 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Harmonized system of quality assessment for electronic components Sectional specification: Waveguide type dielectric resonators Licensed Copy: sheffiel
3、dun sheffieldun, na, Sun Oct 29 10:24:26 GMT+00:00 2006, Uncontrolled Copy, (c) BSI This British Standard, having been prepared under the direction of the Electrotechnical Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 21 Sep
4、tember 2001 BSI 21 September 2001 ISBN 0 580 36509 3 BS EN 170100:2001 Amendments issued since publication Amd. No.DateComments National foreword This British Standard is the official English language version of EN 170100:2001 published by the European Electronic Components Committee (CECC) of the E
5、uropean Committee for Electrotechnical Standardization (CENELEC). The UK participation in its preparation was entrusted to Technical Committee EPL/49, Piezoelectric devices for frequency control and selection, which has the responsibility to: aid enquirers to understand the text; present to the resp
6、onsible International/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on r
7、equest to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled International Standards Correspondence Index, or by using the Find facility of th
8、e BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Sum
9、mary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 19 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 10:24:26 GMT+00:00 20
10、06, Uncontrolled Copy, (c) BSI EUROPEAN STANDARDEN 170100 NORME EUROPENNE EUROPISCHE NORMAugust 2001 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 3
11、5, B - 1050 Brussels 2001 CENELEC -All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 170100:2001 E ICS 31.140 English version Sectional Specification: Waveguide type dielectric resonators Spcification intermdiaire: Rsonateurs dilectriques mod
12、es guids Rahmenspezifikation: Dielektrische Resonatoren vom Wellenleitertyp This European Standard was approved by CENELEC on 2000-08-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a nat
13、ional standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version
14、in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic, Denmark
15、, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 10:24:26 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN :0010711002- - 2 Foreword This European
16、 Standard was prepared by the Technical Committee CENELEC TC 49, Piezoelectric devices for frequency control and selection. The text of the draft was submitted to the Unique Acceptance Procedure and was approved by CENELEC as EN 170100 on 2000-08-01. The following dates were fixed: -latest date by w
17、hich the EN has to be implemented at national level by publication of an identical national standard or by endorsement(dop)2002-02-01 -latest date by which the national standards conflicting with the EN have to be withdrawn(dow)2003-08-01 Annexes designated “normative“ are part of the body of the st
18、andard. In this standard, annexes A, B and C are normative. _ Page 2 EN 170100:2001 Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 10:24:26 GMT+00:00 2006, Uncontrolled Copy, (c) BSI - - 3E:001071 N1002 CONTENTS 1 Scope .4 2General preferred ratings and guidance of detail specifications.4 2.
19、1Related documents 4 2.2Preferred ratings and characteristics4 2.3Information to be prescribed in detail specifications .4 3 Capability approval.5 3.1 Eligibility for capability approval5 3.2 Structural similarity .5 3.3 Procedures for capability approval5 3.4Description of capability6 3.5Capability
20、 Qualifying Components (CQCs7 3.6Inspection requirements for CQCs.7 3.7Programme for capability approval.8 3.8Capability approval report.8 3.9Abstract of description of capability8 3.10Modifications likely to affect capability approval .8 3.11Initial capability approval.8 3.12Maintenance of capabili
21、ty approval.14 3.13Rework and repair work15 3.14Quality conformance inspection15 3.15Screening procedures.16 4Text and measurement procedures16 Annex AExample layout of an abstract of description of capability for inclusion in CECC 00 20017 Annex BLayout of the front page of a CQC specification for
22、process control18 Annex CLayout of the front page of a CQC specification to demonstrate a boundary or limit .19 Page 3 EN 170100:2001 Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 10:24:26 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN :0010711002- - 4 1Scope This sectional specification app
23、lies to waveguide type dielectric resonators as custom built products or as standard catalogue items whose quality is assessed on the basis of capability approval. It prescribes the preferred ratings and characteristics with the appropriate tests and measuring methods contained in the generic specif
24、ication EN 170000, and gives the general performance requirements to be used in detail specifications for waveguide type dielectric resonators. The concept of preferred values is in general directly applicable to standard catalogue items but does not necessarily apply to custom built products. 2Gene
25、ral, preferred ratings and guidance on detail specifications 2.1Related documents EN 60068-1Environmental testing - Part 1: General and guidance (IEC 60068-1) EN 170000Generic specification: Waveguide type dielectric resonators. CECC 00016Basic requirements for the use of Statistical Process Control
26、 (SPC) in the CECC system. NOTE The above references apply to the current editions except for EN 60068-1 for which the referred edition and the applicable test clauses defined in EN 170000 shall be used. 2.2Preferred ratings and characteristics The values given in detail specifications shall prefera
27、bly be selected from those stated in 2.4 of the generic specification EN 170000. 2.3Information to be prescribed in detail specifications (for both custom built and standard catalogue items) Guidance on the preparation of detail specifications is given in the blank detail specification. Each detail
28、specification shall state all the tests and measurements required for inspection. For standard catalogue items this shall, as a minimum, include the relevant tests given in the blank detail specification, with methods and severities. The following information shall be given in each detail specificat
29、ion. 2.3.1Outline drawing and dimensions The detail specification shall include a dimensional drawing of the waveguide type dielectric resonator and/or reference to an appropriate international standard, to permit easy recognition and to provide information for dimensioning and gauging procedures. T
30、he dimensions shall include the overall dimensions of the body of the component and the size and spacing of the terminations. All dimensions shall be stated in mm. Page 4 EN 170100:2001 Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 10:24:26 GMT+00:00 2006, Uncontrolled Copy, (c) BSI - - 5E:
31、001071 N1002 2.3.2Marking The detail specification shall prescribe the content of the marking on the waveguide type dielectric resonator primary package in accordance with 2.5 of EN 170000. 2.3.3Ordering information The detail specification shall prescribe that the following information is required
32、when ordering a waveguide type dielectric resonator. a)Quantity b)Detail specification number, issue number and date and where applicable c)Nominal frequency in MHz or GHz d) Full description of any additional requirements to identify the waveguide type dielectric resonator. 2.3.4Additional informat
33、ion (not for inspection purposes) The detail specification may include information which is not normally required to be verified by the inspection procedure, such as circuit diagrams, curves, drawings and notes needed for clarification. 3Capability approval 3.1Eligibility for capability approval Pri
34、or to making an application for capability approval a manufacturer shall first obtain manufacturers inspection approval in accordance with EN 100114-1. The primary stage of manufacture shall be as defined in 3.1 of the generic specification EN 170000. 3.2Structural similarity Structural similarity i
35、s not applicable to Capability Approval. However, it is applicable to released lots as defined in 3.14.1 of this specification. 3.3Procedures for capability approval 3.3.1General Capability approval in waveguide type dielectric resonator technology covers: -the complete design, material preparation
36、and manufacturing techniques, including control procedures and tests; -the performance limits claimed for the processes and products, that is those specified for the Capability Qualifying Components (CQCs); -the range of mechanical structures for which approval is granted. Page 5 EN 170100:2001 Lice
37、nsed Copy: sheffieldun sheffieldun, na, Sun Oct 29 10:24:26 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN :0010711002- - 6 3.3.2Application for capability approval In order to obtain capability approval the manufacturer shall apply the rules of procedure given in 2.4 of CECC 00 114-3. In an applicat
38、ion for capability approval the manufacturer shall define the boundaries of the capability for which approval is sought in accordance with 3.5. 3.3.3Granting of capability approval Capability approval shall be granted when the manufacturer has: -prepared a capability manual describing the capability
39、 for which he wishes to be approved, to the satisfaction of the ONS; -agreed with the ONS the range of CQCs, as defined in 2.7 of CECC 00 114-3, to be used for the assessment of capability; -successfully demonstrated that he can design and manufacture components which satisfy the requirements of thi
40、s sectional specification, within the limits of his capability; -prepared a capability approval test report to the satisfaction of the ONS. 3.4Description of capability The manufacturer shall prepare a manual describing his capability (see 2.5 of CECC 00 114-3), in relation to the technologies invol
41、ved. The manual shall be approved by the ONS who shall ensure that it is a true and complete record of procedures carried out by the manufacturer during the design, production, testing, inspection and release of his products. The manual is a document that shall be treated as commercial in confidence
42、. The manual shall include the following as a minimum: -A general introduction and description of the technologies involved; -Aspects of customer liaison including provision of design rules (if appropriate) and assistance to customers in the formulation of their requirements; -A detailed description
43、 of the design rules to be used; -The procedure for checking that the design rules are complied with for waveguide type dielectric resonators manufactured to a detail specification; -A list of all materials used, with references to the corresponding purchasing specifications and goods inward inspect
44、ion; -A flow chart for the total process showing quality control points and permitted rework loops and containing references to all process and quality control procedures which may invoke SPC procedures (see CECC 00 016); -A declaration of processes for which approval has been sought in accordance w
45、ith 3.5.1; -A declaration of boundaries for which approval has been sought in accordance with 3.5.2; -A list of CQCs used to assess the capability, with a general description of each, supported by a detailed table showing where the declared boundaries of capability are demonstrated by a particular C
46、QC design; -A detail specification for each CQC. These shall be produced to the satisfaction of the ONS. (see annexes B and C). Page 6 EN 170100:2001 Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 10:24:26 GMT+00:00 2006, Uncontrolled Copy, (c) BSI - - 7E:001071 N1002 3.5Capability Qualifyin
47、g Components (CQCs) The manufacturer shall agree with the ONS the range of capability qualifying components, selected in accordance with the general plan (see 3.11.2) specified in the capability manual. The CQCs shall comply with the following requirements: a)The range of CQCs used shall cover all t
48、he processes, component types and limits of the declared capability b)The CQCs shall be one of the following: -waveguide type dielectric resonators in production; -test pieces designed for assessment of a process or range of processes; -a combination of both of these. When CQCs are designed and prod
49、uced solely for capability approval, the manufacturer shall satisfy the ONS that the same design rules, materials and manufacturing processes will be applied to released products. The CQC specifications may refer to internal control documentation which specifies production testing and recording in order to demonstrate control and maintenance of processes and boundaries including the use of SPC procedures where appropriate. 3.5.1Process The CQC specifications shall include the following processes to be assessed. This list is not exclusive: -Sinterin