《BS-EN-4008-015-2007.pdf》由会员分享，可在线阅读，更多相关《BS-EN-4008-015-2007.pdf（10页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 4008-015:2007 Aerospace series Elements of electrical and optical connection Crimping tool and associated accessories Part 015: Positioner for crimping tool M22520/2-01 Product standard The European Standard EN 4008-015:2007 has the status of a British Standard ICS 49.060 ? Li
2、censed Copy: London South Bank University, London South Bank University, Thu Dec 20 02:56:46 GMT+00:00 2007, Uncontrolled Copy, (c) BSI BS EN 4008-015:2007 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 December 2007 BSI 2007 ISBN 978 0 5
3、80 57220 3 National foreword This British Standard is the UK implementation of EN 4008-015:2007. The UK participation in its preparation was entrusted by Technical Committee ACE/6, Aerospace avionic electrical and fibre optic technology, to Panel ACE/6/-/3, Aerospace Connectors. A list of organizati
4、ons represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations.
5、 Amendments issued since publication Amd. No. DateComments Licensed Copy: London South Bank University, London South Bank University, Thu Dec 20 02:56:46 GMT+00:00 2007, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 4008-015 November 2007 ICS 49.060 English Version
6、Aerospace series - Elements of electrical and optical connection - Crimping tool and associated accessories - Part 015: Positioner for crimping tool M22520/2-01 - Product standard Srie arospatiale - Organes de connexion lectrique et optique - Outils de sertissage et accessoires associs - Partie 015:
7、 Positionneur pour pince sertir M22520/2-01 - Norme de produit Luft- und Raumfahrt - Elektrische und optische Verbinungselemente - Crimpwerkzeug und Zugehriges Zubehr - Teil 015: Positionierer fr Crimzange M22520/2- 01 - Produktnorm This European Standard was approved by CEN on 28 September 2006. CE
8、N members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on app
9、lication to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre
10、 has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
11、 Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2007 CENAll rights of exploitation in any form and by any
12、 means reserved worldwide for CEN national Members. Ref. No. EN 4008-015:2007: E Licensed Copy: London South Bank University, London South Bank University, Thu Dec 20 02:56:46 GMT+00:00 2007, Uncontrolled Copy, (c) BSI 2 Contents Page Foreword3 1 Scope 4 2 Normative references4 3 Terms and definitio
13、ns .4 4 Required characteristics.4 4.1 Description.4 4.2 Dimensions and mass.5 4.3 Material, surface treatment.5 5 Designation 6 6 Marking.6 7 Technical specification .6 EN 4008-015:2007 Licensed Copy: London South Bank University, London South Bank University, Thu Dec 20 02:56:46 GMT+00:00 2007, Un
14、controlled Copy, (c) BSI 3 Foreword This document (EN 4008-015:2007) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the ap
15、proval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2008, and confli
16、cting national standards shall be withdrawn at the latest by May 2008. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to th
17、e CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuan
18、ia, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 4008-015:2007 Licensed Copy: London South Bank University, London South Bank University, Thu Dec 20 02:56:46 GMT+00:00 2007, Uncontrolled Copy, (c) BSI 4 1
19、 Scope This standard specifies the characteristics for the positioner used with M22520/2-01 crimping tool to crimp electrical contact according to EN 4008-002. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only
20、 the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2591-100, Aerospace series Elements of electrical and optical connection Test methods Part 100: General. EN 4008-001, Aerospace series Elements of electrical and o
21、ptical connection Crimping tools and associated accessories Part 001: Technical specification. EN 4008-002, Aerospace series Elements of electrical and optical connection Crimping tools and associated accessories Part 002: List of product standards. MIL-C-22520/2, Crimping tools, terminal, hand, wir
22、e termination for wire barrel sizes 20 through 28. 1) 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 2591-100 apply. 4 Required characteristics 4.1 Description Securing the positioner on the crimping tool is provided by the combined action of the two
23、 bayonets and the pressure from the internal spring on the central moving part (locator). The appropriate longitudinal positioning of the contact with respect to the crimping tool indenters is performed by the contact butting against a shoulder on the central part bore. Locator shall be spring loade
24、d so as to depress 0,79 mm with a force of (9 4,5) N. 1) Published by: Department of Defense (DOD), the Pentagon, Washington D.C.20301 USA. EN 4008-015:2007 Licensed Copy: London South Bank University, London South Bank University, Thu Dec 20 02:56:46 GMT+00:00 2007, Uncontrolled Copy, (c) BSI 5 4.2
25、 Dimensions and mass Dimensions of positioner are given in Figure 1. Mass: 11 g max. Dimensions and tolerances are given in millimetres. General tolerances: 0,25 mm Key 1 Bayonet lock pin 1,09 0,025 2 Locator in extended position 3 Stamp on this surface: “EN4008-015 use with M22520/2-01“ (conform to
26、 MIL-C-22250/2) a Use with contact WIRE WK WL WS XY WG XE SEL 2 1 2 1 1 2 EN3155-028 EN3155-029 Figure 1 Positioner 4.3 Material, surface treatment Positioner body: aluminium alloy, color blue Positioner locator: stainless steel Not applicable EN 4008-015:2007 Licensed Copy: London South Bank Univer
27、sity, London South Bank University, Thu Dec 20 02:56:46 GMT+00:00 2007, Uncontrolled Copy, (c) BSI 6 5 Designation EXAMPLE Description Block POSITIONER Identity Block EN4008-015 Number of this standard NOTE If necessary, the code I9005 shall be placed between the description block and the identity b
28、lock. 6 Marking See Figure 1. 7 Technical specification See EN 4008-001. EN 4008-015:2007 Licensed Copy: London South Bank University, London South Bank University, Thu Dec 20 02:56:46 GMT+00:00 2007, Uncontrolled Copy, (c) BSI blank Licensed Copy: London South Bank University, London South Bank Uni
29、versity, Thu Dec 20 02:56:46 GMT+00:00 2007, Uncontrolled Copy, (c) BSI BS EN 4008-015:2007 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and
30、at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and
31、 services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offe
32、rs members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax:
33、+44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Inform
34、ation on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact t
35、he Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Admi
36、nistration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyr
37、ight subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form
38、 or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used fo
39、r any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-. Licensed Copy: London South Bank University, London South Bank University, Thu Dec 20 02:56:46 GMT+00:00 2007, Uncontrolled Copy, (c) BSI