《BS-EN-4175-2005.pdf》由会员分享，可在线阅读，更多相关《BS-EN-4175-2005.pdf（10页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD AEROSPACE SERIES BS EN 4175:2005 Collars, flanged swage locking, sheartype, in titanium TI-P99002, metric series The European Standard EN 4175:2005 has the status of a British Standard ICS 49.030.50 ? Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 04 08:47:43 GMT+00:00 2006, Un
2、controlled Copy, (c) BSI BS EN 4175:2005 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 18 January 2006 BSI 18 January 2006 ISBN 0 580 47225 6 National foreword This British Standard is the official English language version of EN 4175:2005.
3、The UK participation in its preparation was entrusted to Technical Committee ACE/12, Aerospace fasteners and fastening systems, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards w
4、hich implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publi
5、cation does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible internation
6、al/European committee any enquiries on the interpretation, or proposals for change, and keep UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page,
7、 pages 2 to 6, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. DateComments Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 04 08:47:43 GMT+00:00 2006, Uncontrolle
8、d Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 4175 November 2005 ICS 49.030.50 English Version Aerospace series - Collars, flanged swage locking, sheartype, in titanium TI-P99002, metric series Srie arospatiale - Bagues sertir, collerette, cisaillement, en titane TI-P99002, sr
9、ie mtrique Luft- und Raumfahrt - Schlieringe, mit Bund, Schertyp, aus Titan TI-P99002, metrische Reihe This European Standard was approved by CEN on 30 September 2005. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European St
10、andard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, Frenc
11、h, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republ
12、ic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISAT
13、ION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2005 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 4175:2005: E Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 04 08:47:43 GMT+00:00 20
14、06, Uncontrolled Copy, (c) BSI 2 Contents Page Foreword 3 1 Scope.4 2 Normative references .4 3 Required characteristics 4 4 Designation .6 5 Marking6 6 Technical specification.6 EN 4175:2005 Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 04 08:47:43 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 3
15、 Foreword This European Standard (EN 4175:2005) has been prepared by the European Association of Aerospace Manufacturers - Standardization (AECMA-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Ass
16、ociations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2006, and conflicting national standards
17、 shall be withdrawn at the latest by May 2006. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal R
18、egulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands
19、, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 4175:2005 Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 04 08:47:43 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 4 1 Scope This standard specifies the characteristics of flanged swage collars, s
20、heartype, in titanium TI-P99002, metric series, for maximum operating temperature 315 C and composite applications. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated refe
21、rences, the latest edition of the referenced document (including any amendments) applies. EN 2424, Aerospace series Marking of aerospace products. EN 3460, Aerospace series Titanium TI-P99002 Annealed Bar for machining a or D 150 mm Rm 390 MPa. 1) EN 4176, Aerospace series Lockbolts, 100 countersunk
22、 normal head or protruding head, tension- / sheartype, close tolerance, in titanium alloy TI-P64001, anodized or with aluminium pigmented coating Collars in titanium TI-P99002 or aluminium alloy 2024 Metric series Technical specification. 1) MIL-L-46010D, Lubricant, Solid Film, Heat Cured, Corrosion
23、 Inhibiting. 2) MIL-L-87132B, Lubricant, Cetyl Alcohol, 1-Hexadecanol, Application to Fasteners. 2) 3 Required characteristics 3.1 Configuration Dimensions Masses See Figure 1 and Table 1. Dimensions and tolerances are expressed in millimetres and apply after surface treatment. 3.2 Material See EN 3
24、460. 3.3 Surface treatments MIL-L-46010 Lubrication with cetylic alcohol (chlorine free) according to MIL-L-87132 1) Published as AECMA Prestandard at the date of preparation of this standard. 2) Published by: Department of Defense (DoD), the Pentagon, Washington, D.C.20301, USA. EN 4175:2005 Licens
25、ed Copy: sheffieldun sheffieldun, na, Sat Nov 04 08:47:43 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 5 Key 1 Marking Figure 1 Table 1 D1 D2 D3 H1 H2 R Mass a Diameter code 0 0,1 0 0,15 0 0,1 0 0,5 0 0,25 max. min. 040 4,05 8,176,075,760,51 050 5,05 10,2 7,226,32 0,76 0,70 060 6,05 11,488,587,21 0,46
26、 0,2 1,27 080 8,05 15,4711,489,472,55 100 10,05 18,6914,2311,2 0,89 0,58 0,33 4,11 a Approximate values (kg/1 000 pieces), calculated on the basis of 4,45 kg/dm3, given for information purposes only. Values in micrometres apply prior to surface treatment. EN 4175:2005 Licensed Copy: sheffieldun shef
27、fieldun, na, Sat Nov 04 08:47:43 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 6 4 Designation EXAMPLE Description block COLLAR Identity block EN4175-040 Number of this standard Diameter code (see Table 1) NOTE If necessary, the code I9005 shall be placed between the description block and the identity
28、block 5 Marking EN 2424, style F (see Figure 1). 6 Technical specification See EN 4176. EN 4175:2005 Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 04 08:47:43 GMT+00:00 2006, Uncontrolled Copy, (c) BSI blank Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 04 08:47:43 GMT+00:00 2006, Uncont
29、rolled Copy, (c) BSI BS EN 4175:2005 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal
30、 Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an in
31、accuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS w
32、hich ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are a
33、lso available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of informa
34、tion on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +
35、44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 89
36、96 7001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds t
37、he copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or
38、 otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior
39、written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-. Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 04 08:47:43 GMT+00:00 2006, Uncontrolled Copy, (c) BSI