《BS-EN-60062-1994.pdf》由会员分享，可在线阅读，更多相关《BS-EN-60062-1994.pdf（16页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 60062:1994 IEC 60062:1992 Incorporating Amendments Nos. 1 and 2 Marking codes for resistors and capacitors The European Standard EN 60062:1993, with the incorporation of amendments A1:1997 and A11:2001, has the status of a British Standard ICS 31.040.01; 31.060.01 ? Licensed C
2、opy: sheffieldun sheffieldun, na, Fri Nov 10 17:45:09 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 60062:1994 This British Standard, having been prepared under the direction of the Electronic Components Standards Policy Committee, was published under the authority of the Standards Board and come
3、s into effect on 15 February 1994 BSI 31 January 2003 The following BSI references relate to the work on this standard: Committee reference ECL/4 Special announcement in BSI News December 1993 ISBN 0 580 22918 1 Cooperating organizations The European Committee for Electrotechnical Standardization (C
4、ENELEC), under whose supervision this European Standard was prepared, comprises the national committees of the following countries: AustriaItaly BelgiumLuxembourg DenmarkNetherlands FinlandNorway FrancePortugal GermanySpain GreeceSweden IcelandSwitzerland IrelandUnited Kingdom Amendments issued sinc
5、e publication Amd. No.DateComments 9739December 1997 1423031 January 2003 Indicated by a sideline Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 10 17:45:09 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 60062:1994 BSI 31 January 2003 i Contents Page Cooperating organizationsInside front cove
6、r National forewordii Foreword2 Text of EN 600623 National annex NA (informative) Committees responsible11 National annex NB (informative) Cross-reference11 Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 10 17:45:09 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 60062:1994 ii BSI 31 January 2
7、003 National foreword This British Standard has been prepared under the direction of the Electronic Components Standards Policy Committee and is the English language version of EN 60062:1993, Marking codes for resistors and capacitors, including amendments A1:1997 and A11:2001, published by the Euro
8、pean Committee for Electrotechnical Standardization (CENELEC). It supersedes BS 1852:1975 which is withdrawn. It is identical with IEC 60062:1992, including amendment 1:1995, published by the International Electrotechnical Commission (IEC). Cross-references The British Standards which implement inte
9、rnational or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not pur
10、port to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii,
11、the EN title page, pages 2 to 11 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Sidelining in this document indicates the most recent changes by amendment. Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 10 17:45:09 GMT+00:00 20
12、06, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 60062 October 1993 + A1 May 1997 + A11 May 2001 UDC 621.316.8-777; 621.319.4-777 Supersedes HD 334 S3:1991 Descriptors: Marking, codes, resistors, capacitors English version Marking codes for resistors and capacitors
13、 (includes amendment A1:1997 and A11:2001) (IEC 62:1992 + A1:1995) Codes pour le marquage des rsistances et des condensateurs (inclut les amendements A1:1997 et A11:2001) (CEI 62:1992 + A1:1995) Kennzeichnung von Widerstnden und Kondensatoren (enthlt nderungen A1:1997 und A11:2001) (IEC 62:1992 + A1
14、:1995) This European Standard was approved by CENELEC on 1993-09-22. Amendment A1 was approved by CENELEC on 1997-03-11 and amendment A11 was approved by CENELEC on 2000-04-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving thi
15、s European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official version
16、s (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Au
17、stria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Ko
18、mitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1993 Copyright reserved to CENELEC members Ref. No. EN 60062:1993 + A1:1997 + A11:2001 E Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 10 17:45:09 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60062:199
19、3 BSI 31 January 2003 2 Foreword The CENELEC questionnaire procedure, performed for finding out whether or not the International Standard IEC 62:1992 could be accepted without textual changes, has shown that no common modifications were necessary for the acceptance as European Standard. The referenc
20、e document was submitted to the CENELEC members for formal vote and was approved by CENELEC as EN 60062 on 22 September 1993. This European Standard replaces HD 334 S3:1991. The following dates were fixed: Foreword to amendment A1 The text of amendment 1:1995 to the International Standard IEC 62:199
21、2, prepared by IEC TC 40, Capacitors and resistors for electronic equipment, was submitted to the formal vote and was approved by CENELEC as amendment A1 to EN 60062:1993 on 1997-03-11 without any modification. The following dates were fixed: Foreword to amendment A11 This amendment was prepared by
22、the Technical Committee CENELEC TC 40XA, Capacitors. The text of the draft was submitted to the Unique Acceptance Procedure and was approved by CENELEC as amendment A11 to EN 60062:1993 on 2000-04-01. The following dates were fixed: Contents Page Foreword2 1Scope3 2Colour code for fixed resistors3 3
23、Letter and digit code for resistance and capacitance values5 4Letter code for tolerance on resistance and capacitance values7 5Date code system for capacitors and resistors8 6Code letter (index) for the dielectric material of plastic film and paper capacitors9 Table I Values corresponding to colours
24、3 Table II Examples of code marking for resistance values6 Table III Examples of code marking for capacitance values7 Table IV Letter corresponding to dielectric of plastic film material9 latest date of publication of an identical national standard(dop) 1994-10-01 latest date of withdrawal of confli
25、cting national standards(dow) 1994-10-01 latest date by which the amendment has to be implemented at national level by publication of an identical national standard or by endorsement(dop) 1997-12-01 latest date by which the national standards conflicting with the amendment have to be withdrawn(dow)
26、1997-12-01 latest date by which the amendment has to be implemented at national level by publication of an identical national standard or by endorsement(dop) 2001-10-01 latest date by which the national standards conflicting with the amendment have to be withdrawn(dow) 2003-04-01 Licensed Copy: shef
27、fieldun sheffieldun, na, Fri Nov 10 17:45:09 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60062:1993 BSI 31 January 2003 3 1 Scope This standard specifies marking codes for resistors and capacitors and indexes for the dielectric material and the electrodes of plastic film and paper capacitors. The
28、code specified in Clause 2 gives a colour coding for fixed resistors. It is intended for use with the values of the E6 to E192 series as specified in IEC Publication 60063, Preferred Number Series of Resistors and Capacitors. The code specified in Clause 3 gives a system for marking resistance and c
29、apacitance values by means of letters and digits. The code specified in Clause 4 gives a system for marking the tolerance on resistance and capacitance values by means of a letter. The code specified in Clause 5 gives systems for marking of date codes on capacitors and resistors by means of letters
30、and digits. The code (index) specified in Clause 6 gives a coding system for the dielectric material. 2 Colour code for fixed resistors 2.1 The colour code for indicating resistance values to two and three significant figures, tolerances and if needed, the indication of the temperature coefficient o
31、f fixed resistors shall be as given in Sub-clauses 2.2, 2.3 and 2.4. 2.2 The first band shall be the one nearest to the end of the resistor and the bands shall be so placed and spaced that there can be no confusion in reading the coding. 2.3 Any additional coding shall be so applied as not to confus
32、e the coding for value and tolerance. 2.4 Table I Values corresponding to colours For the indication of temperature coefficients according to the code as described above one of the following methods shall be used: a) a colour band as the sixth and wider band; b) an interrupted colour band as the six
33、th band; c) a helix. For cylindrical types the helix shall be superimposed on the full length of the existing bands of colour code indicating the resistance value and tolerance, with the helix covering not less than 270 degrees of the circumference. ColourSignificant figuresMultiplierToleranceTemper
34、ature coefficient (10-6 ? ?C) Silver 102 10 % Gold 101 5 % Black01250 Brown1101 %100 Red2 102 2 %50 Orange3 103 0,05 %15 Yellow4 104 25 Green5 105 0,5 %20 Blue6 106 0,25 %10 Violet7 107 0,1 %5 Grey8 108 1 White9 109 None20 % Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 10 17:45:09 GMT+00:00 2
35、006, Uncontrolled Copy, (c) BSI EN 60062:1993 4 BSI 31 January 2003 For other types similar methods of colour coding should be used as described in the detail specification. Colour code marking of the temperature coefficient shall only be used in combination with three significant figures. 2.4.1 Exa
36、mple of colour code marking for resistance values with two significant figures Resistor of 27 000 ? with a tolerance of 5 %. 2.4.2 Example of colour code marking for resistance values with three significant figures Resistor of 249 000 ? with a tolerance of ?1 %. NOTEIn order to avoid any confusion,
37、the last band shall be 1,5 to 2 times wider than the other bands. 2.4.3 Example of colour code marking for resistance values with three significant figures and temperature coefficient Resistor of 249 000 ? with a tolerance of ?1 % and a temperature coefficient of ?50 ? 106 ?C. Licensed Copy: sheffie
38、ldun sheffieldun, na, Fri Nov 10 17:45:09 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60062:1993 BSI 31 January 2003 5 NOTEIn order to avoid any confusion, the last band shall be 1,5 to 2 times wider than the other bands. 3 Letter and digit code for resistance and capacitance values 3.1 General ru
39、les 3.1.1 The code shall use 3, 4 or 5 characters consisting of 2 figures and a letter, 3 figures and a letter or 4 figures and a letter as required. 3.1.2 The code letters replace the decimal point as shown in the examples in Table II and Table III. 3.1.3 Any additional code letter or digit shall a
40、ppear after the tolerance letter specified in Clause 4 and shall be so applied as not to confuse the coding for value and tolerance. 3.2 Resistors The letters R, K, M, G and T are used as multipliers for 1; 103; 106; 109 and 1012 respectively of the resistance value expressed in ohms. Licensed Copy:
41、 sheffieldun sheffieldun, na, Fri Nov 10 17:45:09 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60062:1993 6 BSI 31 January 2003 Table II Examples of code marking for resistance values NOTEResistance values expressed by four significant digits shall have code markings as in the examples shown below:
42、 3.3 Capacitors The letters p, n, ?, m and F are used as multipliers for 1012; 109; 106; 103 and 1 respectively of the capacitance value expressed in farads. Resistance valuesCoded markingResistance valuesCoded marking 0,1 0,15 0,332 0,590 1 1,5 3,32 5,90 10 15 33,2 59,0 100 150 332 590 1 1,5 3,32 5
43、,90 10 15 33,2 59,0 100 150 332 590 ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? k? k? k? k? k? k? k? k? k? k? k? k? R10 R15 R332 R59 1R0 1R5 3R32 5R9 10R 15R 33R2 59R 100R 150R 332R 590R 1K0 1K5 3K32 5K9 10K 15K 33K2 59K 100K 150K 332K 590K 1 1,5 3,32 5,90 10 15 33,2 59,0 100 150 332 590 1 1,5 3,32 5,90 10 15 3
44、3,2 59,0 100 150 332 590 1 1,5 3,32 5,90 10 M? M? M? M? M? M? M? M? M? M? M? M? G? G? G? G? G? G? G? G? G? G? G? G? T? T? T? T? T? 1M0 1M5 3M32 5M9 10M 15M 33M2 59M 100M 150M 332M 590M 1G0 1G5 3G32 5G9 10G 15G 33G2 59G 100G 150G 332G 590G 1T0 1T5 3T32 5T9 10T ValueCoded marking 59,04?59R04 590,4?590
45、R4 5,904k?5K904 59,04k?59K04 etc. Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 10 17:45:09 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60062:1993 BSI 31 January 2003 7 Table III Examples of code marking for capacitance values NOTECapacitance values expressed by four significant digits shall
46、 have code markings as in the examples shown below: 4 Letter code for tolerance on resistance and capacitance values 4.1 Symmetrical tolerances in per cent The following letters shall be used for indicating the tolerance on resistance and capacitance values: These letters shall be placed after the r
47、esistance and capacitance values. Capacitance valuesCoded markingCapacitance valuesCoded marking 0,1 0,15 0,332 0,590 1 1,5 3,32 5,90 10 15 33,2 59,0 100 150 332 590 1 1,5 3,32 5,90 10 15 33,2 59,0 pF pF pF pF pF pF pF pF pF pF pF pF pF pF pF pF nF nF nF nF nF nF nF nF p10 p15 p332 p59 1p0 1p5 3p32
48、10p 15p 33p2 59p 100p 150p 332p 590p 1n0 1n5 3n32 5n9 10n 15n 33n2 59n 100 150 332 590 1 1,5 3,32 5,90 10 15 33,2 59,0 100 150 332 590 1 1,5 3,32 5,90 10 15 33,2 59,0 nF nF nF nF ? F ? F ? F ? F ? F ? F ? F ? F ? F ? F ? F ? F mF mF mF mF mF mF mF mF 100n 150n 332n 590n 1 ? 0 1 ? 5 3 ? 32 5 ? 9 10 ?
49、 15 ? 33 ? 2 59 ? 100 ? 150 ? 332 ? 590 ? 1m0 1m5 3m32 5m9 10m 15m 33m2 59m ValueCoded marking 68,01pF68p01 680,1pF680p1 6,801nF6n801 68,01nF68n01 etc. Tolerance % Code letter ?0,005 ?0,01 ?0,02 ?0,05 ?0,1 ?0,25 ?0,5 ?1 ?2 ?5 ?10 ?20 ?30 E L P W B C D F G J K M N Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 10 17:45:09 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60062:1993 8 BSI 31 January 2003 4.2 Asy