《BS-EN-50144-2-10-1996.pdf》由会员分享，可在线阅读，更多相关《BS-EN-50144-2-10-1996.pdf（12页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 50144-2-10: 1996 Safety of hand-held electric motor operated tools Part 2-10: Particular requirements for jig saws The European Standard EN 50144-2-10:1996 has the status of a British Standard ICS 25.080.60; 25.140.20 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 06 06:4
2、1:28 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 50144-2-10:1996 This British Standard, having been prepared under the direction of the Electrotechnical Sector Board, was published under the authority of the Standards Board and comes into effect on 15 October 1996 BSI 11-1998 The following BSI
3、references relate to the work on this standard: Committee reference CPL/61/6 Draft for comment 92/05032 DC ISBN 0 580 26216 2 Committees responsible for this British Standard The preparation of this British Standard was entrusted by Technical Committee CPL/61, Safety of electrical appliances, to Sub
4、committee CPL/61/6, Portable motor-operated tools, upon which the following bodies were represented: Agricultural Engineers Association Association of Control Manufacturers (TACMA (BEAMA Ltd.) Association of Manufacturers Allied to the Electrical and Electronic Industry (BEAMA Ltd.) Association of M
5、anufacturers of Domestic Electrical Appliances Consumer Policy Committee of BSI Consumers Association Department of Trade and Industry (Consumer Safety Unit, CA Division) Electricity Association Health and Safety Executive Hire Association Europe Institution of Incorporated Executive Engineers Porta
6、ble Electric Tool Manufacturers Association Rotating Electrical Machines Association (BEAMA Ltd.) Co-opted members Amendments issued since publication Amd. No.DateComments Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 06 06:41:28 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 50144-2-10:1996
7、 BSI 11-1998i Contents Page Committees responsibleInside front cover National forewordii Foreword2 Text of EN 50144-2-103 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 06 06:41:28 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 50144-2-10:1996 ii BSI 11-1998 National foreword This British Sta
8、ndard has been prepared by Subcommittee CPL/61/6 and is the English language version of EN 50144-2-10:1996 Safety of hand-held electric motor operated tools Part 2-10: Particular requirements for jig saws, published by the European Committee for Electrotechnical Standardization (CENELEC). It is to b
9、e read in conjunction with BS EN 50144-1:1996 General requirements, which it supplements or modifies. The many references to Part 1 should be read as references to BS EN 50144-1:1996, which is the English language version of EN 50144-1:1995. The foreword of EN 50144-2-10 makes reference to the “date
10、 of withdrawal”, dow, of the relevant national standard. In this case the relevant national standard is BS 2769-2.10:1984 which will be withdrawn on 1 December 1996 in accordance with the CENELEC Internal Regulations. Reference is also made to the application of CENELEC Memorandum No. 6 with regard
11、to certification. Attention is drawn to Note 7 to Memorandum No. 6 which states: “The use of the certificate or mark licence in the running production may not go on for more than 60 months after dow. This should allow necessary changes in the production line and to use up supplies. Within the establ
12、ished period after dow the certificates and mark licences will have to be reconsidered and cancelled or reissued”. For tools intended to be used in locations where special conditions prevail, as in ships and vehicles, and in hazardous locations, for example, where explosions are liable to occur, req
13、uirements additional to those specified in the standard may be necessary. This standard calls for test procedures that may be injurious to safety or health if adequate precautions are not taken when conducting tests. Product certification Attention is drawn to the fact that products conforming to th
14、is British Standard may be approved by BSI Product Certification, and that such certification may be used for the purposes of participation in the CENELEC Certification Agreement. (Details of the BSI certification marks are given on the inside back cover.) A British Standard does not purport to incl
15、ude all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages
16、 i and ii, the EN title page, pages 2 to 6, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Licensed Copy: sheffieldun sheffieldun, na, Mon No
17、v 06 06:41:28 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 50144-2-10 February 1996 ICS 25.140.20; 25.080.60Supersedes HD 400.3J S1:1981 Descriptors: Hand-held electric motor operated tools, jig saws, safety requirements, protection against electric
18、 shocks, fire protection, protection against mechanical hazards English version Safety of hand-held electric motor operated tools Part 2-10: Particular requirements for jig saws Scurit des outils lectroportatifs moteur Partie 2-10: Rgles particulires pour les scies sauteuses Sicherheit von handgefhr
19、ten motorbetriebenen Elektrowerkzeugen Teil 2-10: Besondere Anforderungen fr Spannvorrichtungssgen This European Standard was approved by CENELEC on 1994-10-04. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Stand
20、ard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, Fren
21、ch, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium,
22、Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektro
23、technische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1996 Copyright reserved to CENELEC members Ref. No. EN 50144-2-10:1996 E Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 06 06:41:28 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 50144-2-10:1996 BSI 11-1998 2 Foreword Th
24、is European Standard has been prepared by the Technical Committee 61F, Hand-held and transportable electric motor operated tools. The text of the draft was submitted to the Unique Acceptance Procedure (UAP) in December 1993 and was approved by CENELEC as EN 50144-2-10 on 1994-10-04. A draft for an a
25、mendment was submitted to the Unique Acceptance Procedure in April 1994 and was approved by CENELEC on 1994-10-04 for inclusion into the European Standard. This European Standard replaces HD 400.3J S1:1981. The following dates were fixed: As far as certification is concerned, CENELEC Memorandum 6 ap
26、plies. This standard is divided into two Parts: Part 1: General Requirements, comprising clauses of a general character. Part 2: Particular Requirements, dealing with particular types of appliance. The clauses of these particular requirements supplement or modify the corresponding clauses in Part 1.
27、 Where the text of Part 2 indicates an “addition” to, a “modification” or “replacement” of the relevant requirement, test specification or explanation of Part 1, these changes are made to the relevant text of Part 1, which then becomes part of the standard. Where no change is necessary, the words “T
28、his clause of Part 1 is applicable” are used in Part 2. Tables and figures which are additional to those in Part 1 are numbered starting from 101. NOTEIn this standard the following print types are used: Requirements proper: in roman type; Test specification: in italic type; Explanatory matter: in s
29、mall roman type. Contents Page 1Scope3 2Definitions3 3General requirements3 4General conditions for the tests3 5Rating3 6Classification3 7Marking3 8Protection against electric shock3 9Starting3 10Input and current3 11Heating3 12Leakage current3 13Environmental requirements3 14Moisture resistance4 15
30、Insulation resistance and electric strength4 16Endurance4 17Abnormal operation4 18Mechanical hazards4 19Mechanical strength4 20Construction4 21Components4 22Internal wiring4 23Supply connection and external flexible cables and cords4 24Terminals for external conductors4 25Provision for earthing4 26S
31、crews and connections4 27Creepage distances, clearances and distances through insulation4 28Resistance to heat, fire and tracking4 29Resistance to rusting5 30Radiation5 Annexes6 Figure 101 Test probe5 Table 101 Test conditions for jig saws4 latest date by which the EN has to be implemented at nation
32、al level by publication of an identical national standard or by endorsement(dop) 1996-09-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 1996-12-01 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 06 06:41:28 GMT+00:00 2006, Uncontrolled Copy, (c)
33、 BSI EN 50144-2-10:1996 BSI 11-19983 1 Scope This clause of Part 1 is applicable except as follows: 1.1 Addition: This standard applies to jig saws. NOTEThis standard does not apply to sabre saws. 2 Definitions This clause of Part 1 is applicable except as follows: 2.2 Addition: 18 normal load for j
34、ig saws intended to cut wood the load obtained when the saw is operated continuously with the saw blade in the vertical position, the load being such that the input, in watts, is equal to: where s is the maximum cutting depth, in millimetres, marked on the saw, and n the number of reciprocations per
35、 minute under no-load conditions as marked on the saw 3 General requirements This clause of Part 1 is applicable. 4 General conditions for the tests This clause of Part 1 is applicable except as follows: 4.10 Addition: For tests carried out under normal load, the reciprocating mechanism may be repla
36、ced by a rotating gear, so that the jig saw can be loaded by means of a brake. 5 Rating This clause of Part 1 is applicable. 6 Classification This clause of Part 1 is applicable. 7 Marking This clause of Part 1 is applicable except as follows: 7.1 Addition: Jig saws intended to cut wood shall be mar
37、ked with: maximum cutting depth in millimetres; number of reciprocations per minute under no-load conditions. NOTEThe number of reciprocations under no-load conditions determined after the jig saw has been running idle for 10 min at rated voltage or at the upper limit of the rated voltage range. 7.1
38、3 Addition: If the jig saw is fitted with a device which allows the connection of external dust collection equipment, in the instruction sheet instructions shall be given as to how to connect such a device. 8 Protection against electric shock This clause of Part 1 is applicable. 9 Starting This clau
39、se of Part 1 is applicable. 10 Input and current This clause of Part 1 is applicable except as follows: 10.1 Modification: Compliance is checked by measuring the input after the jig saw has been operating for 10 min. 10.2 Addition: The measurement should be made after the jig saw has been operating
40、for 10 min. 11 Heating This clause of Part 1 is applicable except as follows: 11.5 Addition: The jig saw is operated for 30 min. 12 Leakage current This clause of Part 1 is applicable. 13 Environmental requirements This clause of Part 1 is applicable except as follows: 13.1 Addition: If jig saws are
41、 fitted with integral dust collection devices or devices which allow the connection of external collection equipment, the tests under working conditions, orientation within the cabin and material to be worked shall be in accordance with the following: 0 1s n, MaterialChipboard 19 mm 800 mm 400 mm Fe
42、ed-speedAt a brisk pace without overloading the tool Depth of cutBlade to extend beyond thickness of the material being cut at all times Width of cut-off10 mm Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 06 06:41:28 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 50144-2-10:1996 4 BSI 11-1998 1
43、3.2.3 Replacement of paragraphs 1, 2, 3 and 4: Jig saws are tested at no-load. 13.3.7 Replacement of paragraph 1: Jig saws are tested under load under the conditions shown in Table 101, pendulum systems, if any, being set at maximum. Table 101 Test conditions for jig saws Paragraph 3 is not applicab
44、le. 14 Moisture resistance This clause of Part 1 is applicable. 15 Insulation resistance and electric strength This clause of Part 1 is applicable. 16 Endurance This clause of Part 1 is applicable. 17 Abnormal operation This clause of Part 1 is applicable. 18 Mechanical hazards This clause of Part 1
45、 is applicable except as follows: 18.1 Replacement: A guard shall be provided to prevent inadvertent contact with moving parts above the guide plate. Compliance is checked by the following test: The jig saw is set for a right-angled cut. The test probe of Figure 101 a) is positioned above the guide
46、plate as shown in Figure 101 b) and Figure 101 c). The longitudinal axis of the test probe shall be perpendicular to the toothed rim of the saw blade. The test probe shall be equally shared about the central plane of the saw blade. When the test probe is moved towards the saw blade, it should not be
47、 able to touch its toothed rim. 19 Mechanical strength This clause of Part 1 is applicable. 20 Construction This clause of Part 1 is applicable. 21 Components This clause of Part 1 is applicable. 22 Internal wiring This clause of Part 1 is applicable. 23 Supply connection and external flexible cable
48、s and cords This clause of Part 1 is applicable. 24 Terminals for external conductors This clause of Part 1 is applicable. 25 Provision for earthing This clause of Part 1 is applicable. 26 Screws and connections This clause of Part 1 is applicable. 27 Creepage distances, clearances and distances thr
49、ough insulation This clause of Part 1 is applicable. 28 Resistance to heat, fire and tracking This clause of Part 1 is applicable. Tool bit/cutter/abrasive New blade, as recommended by the manufacturer for chipboard, at the start of each test period Integral collection (if any) Emptied during 7 min rest time OrientationAcross the cabin with the airflow from left to right of the tool Test cycle10 cuts in 5 min, with pendulum action (if any) set at maximum, then 7 min rest time (total 12 min) Test period5 complete cycles (total 1 h