《BS-ISO-12575-2-2007.pdf》由会员分享，可在线阅读，更多相关《BS-ISO-12575-2-2007.pdf（12页珍藏版）》请在三一文库上搜索。
1、BS ISO 12575-2:2007 ICS 91.120.10 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BRITISH STANDARD Thermal insulation products Exterior insulating systems for foundations Part 2: Principal responsibilities of installers Licensed CopyChinese University of Hong Kong, 21/10/2008
2、03:07, Uncontrolled Copy, (c) BSI This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 September 2008 BSI 2008 ISBN 978 0 580 55054 6 Amendments/corrigenda issued since publication DateComments BS ISO 12575-2:2007 National foreword This British
3、 Standard is the UK implementation of ISO 12575-2:2007. The UK participation in its preparation was entrusted to Technical Committee B/540, Energy performance of materials components and buildings. A list of organizations represented on this committee can be obtained on request to its secretary. Thi
4、s publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Licensed CopyChinese University of Hong Kong, 21/10/2008 03:07, Uncontrolled Copy
5、, (c) BSI BS ISO 12575-2:2007 INTERNATIONAL STANDARD ISO 12575-2 First edition 2007-10-01 Reference number ISO 12575-2:2007(E) ISO 2007 Thermal insulation products Exterior insulating systems for foundations Part 2: Principal responsibilities of installers Produits isolants thermiques Applications e
6、xternes aux murs des fondations Partie 2: Principales responsabilits des installateurs Licensed CopyChinese University of Hong Kong, 21/10/2008 03:07, Uncontrolled Copy, (c) BSI BS ISO 12575-2:2007 ISO 12575-2:2007(E) ii ISO 2007 All rights reserved PDF disclaimer This PDF file may contain embedded
7、typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not i
8、nfringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were
9、optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2007 All rights reserve
10、d. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester
11、. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland Licensed CopyChinese University of Hong Kong, 21/10/2008 03:07, Uncontrolled Copy, (c) BSI BS ISO 12575-2:2007 ISO 12575-2:2007(E) IS
12、O 2007 All rights reserved iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body intere
13、sted in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
14、Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the tec
15、hnical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO
16、 shall not be held responsible for identifying any or all such patent rights. ISO 12575-2 was prepared by Technical Committee ISO/TC 163, Thermal performance and energy use in the built environment, Subcommittee SC 3, Thermal insulation products. ISO 12575 consists of the following parts, under the
17、general title Thermal insulation products Exterior insulating systems for foundations: Part 1: Specification Part 2: Principal responsibilities of installers Part 3: Test methods Licensed CopyChinese University of Hong Kong, 21/10/2008 03:07, Uncontrolled Copy, (c) BSI BS ISO 12575-2:2007 ISO 12575-
18、2:2007(E) iv ISO 2007 All rights reserved Introduction ISO 12575 defines a number of types of foundation insulating systems and outlines the different roles the insulation play within each system. This part of ISO 12575 outlines the responsibilities for the installer to install the material in accor
19、dance with the manufacturers instructions and in accordance with local regulations and to document that this has been done. The designer has the responsibility for selecting the actual product in accordance with the minimum requirements in this specification for that type of system. The designer is
20、required to consult the appropriate product standard for the product selected. The manufacturer has the responsibility to produce the product according to any applicable material specification, declare that their product type meets the requirements of this standard, declare the fitness for the inten
21、ded use and label the product according to this standard. The installer is required to install the product in accordance with the manufacturers instructions; assume the responsibilities for installation and be responsible for meeting local government regulations. Development of this part of ISO 1257
22、5 includes a review of applicable CEN documents and CEN material is harmonized where appropriate. Licensed CopyChinese University of Hong Kong, 21/10/2008 03:07, Uncontrolled Copy, (c) BSI BS ISO 12575-2:2007 INTERNATIONAL STANDARDISO 12575-2:2007(E) ISO 2007 All rights reserved 1 Thermal insulation
23、 products Exterior insulating systems for foundations Part 2: Principal responsibilities of installers 1Scope This part of ISO 12575 specifies the responsibilities of the installers of exterior insulating systems for foundations such that a product that is manufactured and packaged in accordance wit
24、h ISO 12575-1 is able to provide the properties declared by the manufacturer when installed according to this part of ISO 12575. This part of ISO 12575 stipulates responsibilities of the installer in the installation of the exterior insulation system, documentation of the installation and a declarat
25、ion by the installer that all requirements of this part of ISO 12575 have been met. This part of ISO 12575 does not specify the fitness of the product for the intended use beyond those aspects relating to installation. Many aspects relating to the fitness for use are specified in ISO 12575-1. The in
26、staller can be required to meet additional requirements specified in local regulations or the customers requirements. 2Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated ref
27、erences, the latest edition of the referenced document (including any amendments) applies. ISO 9229, Thermal insulation Vocabulary ISO 12575-1, Thermal insulation Exterior insulating systems for foundations Part 1: Specification 3Terms and definitions For the purposes of this document, the terms and
28、 definitions given in ISO 9229 apply. 4Requirements 4.1General requirements The installer shall ensure that the product for installation be suitable for the application, based on jurisdiction requirements and the manufacturers recommendations. The installer shall ensure that the product for installa
29、tion has been declared by the manufacturer to meet the requirements of ISO 12575-1. Licensed CopyChinese University of Hong Kong, 21/10/2008 03:07, Uncontrolled Copy, (c) BSI BS ISO 12575-2:2007 ISO 12575-2:2007(E) 2 ISO 2007 All rights reserved 4.2Detailed requirements The installer is responsible
30、for obtaining training on the means by which the manufacturer declares conformity to ISO 12575-1 and on how to interpret the manufacturers marking on the product. The installer shall ensure that the insulation has a reasonably uniform insulating value over the entire face of the insulated area. The
31、installer shall ensure that the installed insulation levels can meet or exceed either the minimum jurisdiction requirements or the engineered, energy-efficient design specification. The installer shall ensure that any insulation that is exposed to the weather or subject to mechanical damage be prote
32、cted. This protection shall extend far enough into the soil to account for settlement of the soil over time. The installer shall ensure, when carbon steel connectors, frame or furring are used, that these members are corrosion-resistant. 5Applications This part of ISO 12575 applies to perimeter wall
33、s, frost walls and load-bearing applications with fastened, adhered, furred, frame or soil-pressure methods of holding insulation and any protection boards or protective surfacing in position. Applications shall comply with any job specifications, together with building code requirements, manufactur
34、ers installation instructions, or good building practices. 6Site testing In case of a dispute between a manufacturer and an installer that cannot be resolved, tests by an accredited third party testing agency to the appropriate material standard shall be accepted. In case of an application dispute b
35、etween an installer and an owner or owners agent that cannot be resolved, opinions by a mutually recognized and qualified professional shall be accepted. NOTEInstallers are not expected to do quality-assurance testing of insulation, fasteners, furring framing or protection materials; this is the res
36、ponsibility of the material manufacturer prior to shipment. 7Marking and labelling 7.1Manufacturers marking The Installer shall determine where or by what means the manufacturer declares conformity to ISO 12575-1. The installer shall identify, verify and record how the material was marked on the dai
37、ly work record. 7.2Job-site label The installer shall attach a job-site label on each complete application, in a prominent location on the site, to identify the application as meeting the requirements of this part of ISO 12575 and the manufacturers instructions. 8Documentation The installer shall ob
38、tain the manufacturers documentation or a third-party certification of compliance to ISO 12575-1 and the applicable material standard. Licensed CopyChinese University of Hong Kong, 21/10/2008 03:07, Uncontrolled Copy, (c) BSI BS ISO 12575-2:2007 ISO 12575-2:2007(E) ISO 2007 All rights reserved 3 9Li
39、mitations Manufacturers are not responsible for the installation workmanship by installers. Installers are not responsible for the adequacy of designs and job specifications. Manufacturers installation recommendations are for the information of the project designer. The project designer, engineer or
40、 architect is responsible for the suitability and performance of a design. Licensed CopyChinese University of Hong Kong, 21/10/2008 03:07, Uncontrolled Copy, (c) BSI BS ISO 12575-2:2007 ISO 12575-2:2007(E) ICS 91.120.10 Price based on 3 pages ISO 2007 All rights reserved Licensed CopyChinese Univers
41、ity of Hong Kong, 21/10/2008 03:07, Uncontrolled Copy, (c) BSI BS ISO 12575-2:2007 This page has been intentionally left blank Licensed CopyChinese University of Hong Kong, 21/10/2008 03:07, Uncontrolled Copy, (c) BSI BS ISO 12575-2:2007 BSI Group Headquarters 389 Chiswick High Road, London, W4 4AL,
42、 UK Tel +44 (0)20 8996 9001 Fax +44 (0)20 8996 7001 standards BSI - British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Rev
43、isions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or a
44、mbiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures
45、that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001 Email: You may also buy directly using a debit/
46、credit card from the BSI Shop on the Website http:/ In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of informati
47、on on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact Information Centre. Tel: +44 (0)20 8996 7111 Fax: +44 (0)2
48、0 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: In
49、formation regarding online access to British Standards via British Standards Online can be found at http:/ Further information about BSI is available on the BSI website at http:/ Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs