《BS-EN-754-4-2008.pdf》由会员分享，可在线阅读，更多相关《BS-EN-754-4-2008.pdf（12页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 754-4:2008 Aluminium and aluminium alloys Cold drawn rod/bar and tube Part 4: Square bars, tolerances on dimensions and form ICS 77.150.10 ? BS EN 754-4:2008 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 April 2008
2、 BSI 2008 ISBN 978 0 580 55597 8 National foreword This British Standard is the UK implementation of EN 754-4:2008. It supersedes BS EN 754-4:1996 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee NFE/35, Light metals and their alloys. A list of organiz
3、ations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligatio
4、ns. Amendments/corrigenda issued since publication DateComments EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 754-4 March 2008 ICS 77.150.10Supersedes EN 754-4:1995 English Version Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 4: Square bars, tolerances on dimensions and
5、 form Aluminium et alliages daluminium - Barres et tubes tirs - Partie 4: Barres carres, tolrances sur dimensions et forme Aluminium und Aluminiumlegierungen - Gezogene Stangen und Rohre - Teil 4: Vierkantstangen, Grenzabmae und Formtoleranzen This European Standard was approved by CEN on 10 Februar
6、y 2008. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtai
7、ned on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Managem
8、ent Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norwa
9、y, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2008 CENAll rights of exploitation in any form
10、and by any means reserved worldwide for CEN national Members. Ref. No. EN 754-4:2008: E EN 754-4:2008 (E) 2 Contents Page Foreword3 1 Scope 4 2 Tolerances on dimensions .4 2.1 Width across flats4 2.2 Corner radii.4 2.3 Length.5 2.4 Squareness of cut ends 5 3 Tolerance on form5 3.1 Straightness.5 3.2
11、 Convexity - Concavity .6 3.3 Twist6 3.4 Squareness.7 Bibliography9 BS EN 754-4:2008 EN 754-4:2008 (E) 3 Foreword This document (EN 754-4:2008) has been prepared by Technical Committee CEN/TC 132 “Aluminium and aluminium alloys”, the secretariat of which is held by AFNOR. This European Standard shal
12、l be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2008, and conflicting national standards shall be withdrawn at the latest by September 2008. This document supersedes EN 754-4:1995. Within its programme of work, Te
13、chnical committee CEN/TC 132 entrusted CEN/TC 132/WG 5 “Extruded and drawn products“ to revise EN 754-4:1995. The following technical modifications have been introduced during the revision: Only editorial changes to bring this part in line with the other parts of EN 754 EN 754 comprises the followin
14、g parts under the general title “Aluminium and aluminium alloys Cold drawn rod/bar and tube“: Part 1: Technical conditions for inspection and delivery Part 2: Mechanical properties Part 3: Round bars, tolerances on dimensions and form Part 4: Square bars, tolerances on dimensions and form Part 5: Re
15、ctangular bars, tolerances on dimensions and form Part 6: Hexagonal bars, tolerances on dimensions and form Part 7: Seamless tubes, tolerances on dimensions and form Part 8: Porthole tubes, tolerances on dimensions and form Attention is drawn to the possibility that some of the elements of this docu
16、ment may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. CEN/TC 132 affirms it is its policy that in the case when a patentee refuses to grant licenses on standardized standards products under reasonable and not discrim
17、inatory conditions then this product shall be removed from the corresponding standard. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic,
18、 Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 754-4:2008 EN 754-4:2008 (E) 4 1 Scope This docume
19、nt specifies the tolerances on dimensions and form for aluminium and aluminium alloy cold drawn square bars having widths across flats from 3 mm up to and including 100 mm. The temper designations used in this part are according to EN 515. 2 Tolerances on dimensions 2.1 Width across flats The tolera
20、nces on width across flats are specified in Table 1. Table 1 Width across flats tolerances Dimensions in millimetres Width across flats S Over Up to and including Tolerances 3 6 08, 0 0 6 10 09, 0 0 10 18 11, 0 0 18 30 13, 0 0 30 50 16, 0 0 50 65 19, 0 0 65 80 30, 0 0 80 100 35, 0 0 2.2 Corner radii
21、 Maximum corner radii are specified in Table 2. BS EN 754-4:2008 EN 754-4:2008 (E) 5 Table 2 Maximum corner radii Dimensions in millimetres Width across flats S Over Up to and including Maximum corner radii 3 8 0,4 8 30 0,8 30 60 1,0 60 80 1,5 80 100 2,0 2.3 Length If fixed lengths are to be supplie
22、d, this shall be stated in the order document. The fixed length tolerances are specified in Table 3. Table 3 Fixed length tolerances Dimensions in millimetres Width across flats S Tolerances on length From Up to and including L 2 000 2 000 5 000 3 100 0 5+ 0 7+ 0 10+ If no fixed or minimum length is
23、 specified in the order, square drawn bars may be delivered in random lengths. The actual lengths and tolerances on random lengths shall be agreed between supplier and purchaser. 2.4 Squareness of cut ends The squareness of cut ends shall be within half of the fixed-length tolerance range (Table 3)
24、for both fixed and random lengths, (e.g. for a fixed length tolerance of 10 0 + mm the squareness of cut ends shall be within 5 mm). 3 Tolerance on form 3.1 Straightness Deviations from straightness, hs and ht, shall be measured as shown in Figure 1 with the square bar placed on a horizontal base pl
25、ate so that its mass decreases the deviation. For square bars with width across flats equal or greater than 10 mm, the straightness tolerances are specified in Table 4. (The straightness tolerance ht applies to the whole length, e.g. for a length of 6 m the maximum deviation from straightness ht is
26、the value given in the table multiplied by 6 m). For square bars with width across flats less than 10 mm, the straightness tolerances shall be agreed upon between supplier and purchaser. BS EN 754-4:2008 EN 754-4:2008 (E) 6 The straightness tolerances apply to square bars in all tempers except O and
27、 Tx51. If a straightness tolerance is required for either O or Tx51 temper, it shall be agreed between supplier and purchaser. Key 1 base plate 2 straight edge Figure 1 Measurement of deviation from straightness Table 4 Straightness tolerances Dimensions in millimetres Width across flats S From Up t
28、o and including Maximum deviation from straightness per metre length ht/length mm/m Maximum localized kink in any 300 mm portion hs 10 100 2 0,6 3.2 Convexity - Concavity The convexity - concavity for square bars shall be included within the width across flats tolerances as given in Table 1. 3.3 Twi
29、st The twist measurement shall be carried out as shown in Figure 2. The twist tolerances are specified in Table 5. For square bars with width across flats less than 10 mm, the twist tolerances shall be agreed between supplier and purchaser. The twist tolerances apply to bars in all tempers except O
30、and Tx51. If a twist tolerance is required for either O or Tx51 temper, it shall be agreed between supplier and purchaser. BS EN 754-4:2008 EN 754-4:2008 (E) 7 Key 1 base plate Figure 2 Measurement of twist Table 5 Twist tolerances Dimensions in millimetres Width across flats S Twist tolerances T Ov
31、er Up to and including per 1 000 mm of length over the total length 10 30 1,0 3,0 30 60 1,5 3,5 60 100 2,0 4,0 3.4 Squareness The deviation from square shall be measured as shown in Figure 3. Squareness tolerances are specified in Table 6. BS EN 754-4:2008 EN 754-4:2008 (E) 8 Figure 3 Measurement of
32、 deviation from square Table 6 Squareness tolerances Dimensions in millimetres Width across flats S From Up to and including Maximum deviation from square Z 3 100 0,005 x width BS EN 754-4:2008 EN 754-4:2008 (E) 9 Bibliography 1 EN 515, Aluminium and aluminium alloys Wrought products Temper designat
33、ions BS EN 754-4:2008 BS EN 754-4:2008 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Roy
34、al Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an
35、inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS
36、 which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are
37、 also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of infor
38、mation on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax:
39、 +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20
40、8996 7001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds
41、 the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording
42、or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.