《BS-TA-49-1973.pdf》由会员分享,可在线阅读,更多相关《BS-TA-49-1973.pdf(8页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD AEROSPACE SERIES BS TA 49:1973 (Superseding, in part, BS TA 35) Incorporating Amendment No. 1 Specification for Bar and section for machining of titanium-aluminium- molybdenum-tin-silicon alloy (Tensile strength 10001200 N/mm2) (Limiting ruling section over 100 mm up to and includin
2、g 150 mm) UDC 629.7:669.295.571286782.018.23 422.2 Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 03:02:13 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS TA 49:1973 This British Standard, having been approved by the Aerospace Industry Standards Committee, was pu
3、blished under the authority of the Executive Board on 2 February 1973 BSI 02-2000 The following BSI references relate to the work on this standard: Committee reference ACE/49 Draft for comment 72/33667 ISBN 0 580 07028 X A British Standard does not purport to include all the necessary provisions of
4、a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 and 2 and a back
5、cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No.Date of issueComments 3430December 1980 Indicated by a sideline in the margin Lice
6、nsed Copy: London South Bank University, London South Bank University, Sat Dec 09 03:02:13 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS TA 49:1973 BSI 02-2000i Contents Page 1Inspection and testing procedure1 2Manufacture1 3Chemical composition1 4Condition1 5Heat treatment1 6Mechanical properties1
7、Appendix A British Standards covering other forms of material of similar composition2 Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 03:02:13 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ii blank Licensed Copy: London South Bank University, London South Bank Univ
8、ersity, Sat Dec 09 03:02:13 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS TA 49:1973 BSI 02-20001 NOTEOther forms of material of similar composition are covered by British Standards as listed in Appendix A. 1 Inspection and testing procedure This British Standard shall be used in conjunction with Se
9、ctions 1 and 2 of BS TA 100. 2 Manufacture The material shall be made from ingots produced, by consumable electrode melting, from materials having a total carbon content of not more than 0.08 % 3 Chemical composition The chemical composition of the materials shall be: 4 Condition Unless otherwise st
10、ated on the drawing, order or Inspection Schedule, the material shall be supplied fully heat treated and either centreless ground or machined. 5 Heat treatment The material and test samples shall be heat treated as follows: 1) heat at a temperature of 900 10 C and hold for 1 h per 25 mm of section,
11、with a minimum of 20 min; 2) cool in air; 3) heat at a temperature of 500 5 C and hold for 24 h; 4) cool in air. 6 Mechanical properties 6.1 The mechanical properties obtained from test pieces selected, prepared, and tested in accordance with the relevant requirements of BS TA 100 shall be: 6.1.1 Te
12、nsile test at room temperature 6.1.2 Creep test. When required and stated on the drawing, order or Inspection Schedule: Maximum total plastic strain in 100 h under a load of 465 N/mm2 at 400 C: 0.10 %. NOTE1 N/mm2= 1 MN/m2= 1 MPa = 0.1 hbar = 0.065 tonf/in2. Information on SI units is given in BS 37
13、63, “The International System of units (SI)” and BS 350, “Conversion factors and tables”. Element % min.max. Aluminium Molybdenum Tin Silicon Iron Hydrogen Oxygen Nitrogen Oxygen + 2 nitrogen Titanium 3.0 3.0 1.5 0.3 5.0 5.0 2.5 0.7 0.20 0.0125 0.25 0.03 0.27 Remainder 0.2 % proof stress Tensile str
14、engthElongation Reduction of area min.min.max.min.min. N/mm2N/mm2N/mm2% 8701 0001 200920 Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 03:02:13 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS TA 49:1973 2 BSI 02-2000 Appendix A British Standards covering other f
15、orms of material of similar composition Tensile strength (N/mm2) min.1 1001 0501 0501 0501 000 max.1 2801 2201 2201 2001 200 Limiting ruling section (mm) Over25100 Up to and including25100100100150 FormBritish Standard Bar and section for machining Forging stock Forgings BS TA 45BS TA 46 BS TA 47 BS
16、 TA 48 BS TA 50 BS TA 51 Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 03:02:13 GMT+00:00 2006, Uncontrolled Copy, (c) BSI blank Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 03:02:13 GMT+00:00 2006, Uncontrolled Copy, (
17、c) BSI BS TA 49:1973 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisi
18、ons British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambi
19、guity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscriber
20、s automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to sup
21、ply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various
22、BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purc
23、hase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies.
24、Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use,
25、 in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070. Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 03:02:13 GMT+00:00 2006, Uncontrolled Copy, (c) BSI