《IEC-60384-25-2006.pdf》由会员分享，可在线阅读，更多相关《IEC-60384-25-2006.pdf（35页珍藏版）》请在三一文库上搜索。
1、IEC 60384-25 (First edition 2006) Fixed capacitors for use in electronic equipment Part 25: Sectional specification Surface mount fixed aluminium electrolytic capacitors with conductive polymer solid electrolyte CORRIGENDUM 1 Page 6 1.3 Normative references Delete the following reference: IEC 62378,
2、 Capacitors and resistors Conformity assessment procedures Generic standard Page 10 3.4.1 Qualification approval on the basis of the fixed sample size procedures Delete the first sentence. October 2006 Copyright International Electrotechnical Commission Provided by IHS under license with IECLicensee
3、=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/10/2007 04:51:21 MSTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARD IEC 60384-25 First edition 2006-06 Fixed capacitors for use in electronic equipment Part 25: Sectional specification Surfa
4、ce mount fixed aluminium electrolytic capacitors with conductive polymer solid electrolyte Reference number IEC 60384-25:2006(E) Copyright International Electrotechnical Commission Provided by IHS under license with IECLicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/10/2007 0
5、4:51:21 MSTNo reproduction or networking permitted without license from IHS -,-,- Publication numbering As from 1 January 1997 all IEC publications are issued with a designation in the 60000 series. For example, IEC 34-1 is now referred to as IEC 60034-1. Consolidated editions The IEC is now publish
6、ing consolidated versions of its publications. For example, edition numbers 1.0, 1.1 and 1.2 refer, respectively, to the base publication, the base publication incorporating amendment 1 and the base publication incorporating amendments 1 and 2. Further information on IEC publications The technical c
7、ontent of IEC publications is kept under constant review by the IEC, thus ensuring that the content reflects current technology. Information relating to this publication, including its validity, is available in the IEC Catalogue of publications (see below) in addition to new editions, amendments and
8、 corrigenda. Information on the subjects under consideration and work in progress undertaken by the technical committee which has prepared this publication, as well as the list of publications issued, is also available from the following: IEC Web Site (www.iec.ch) Catalogue of IEC publications The o
9、n-line catalogue on the IEC web site (www.iec.ch/searchpub) enables you to search by a variety of criteria including text searches, technical committees and date of publication. On-line information is also available on recently issued publications, withdrawn and replaced publications, as well as cor
10、rigenda. IEC Just Published This summary of recently issued publications (www.iec.ch/online_news/ justpub) is also available by email. Please contact the Customer Service Centre (see below) for further information. Customer Service Centre If you have any questions regarding this publication or need
11、further assistance, please contact the Customer Service Centre: Email: custserviec.ch Tel: +41 22 919 02 11 Fax: +41 22 919 03 00 Copyright International Electrotechnical Commission Provided by IHS under license with IECLicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/10/2007
12、04:51:21 MSTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARD IEC 60384-25 First edition 2006-06 Fixed capacitors for use in electronic equipment Part 25: Sectional specification Surface mount fixed aluminium electrolytic capacitors with conductive polymer
13、 solid electrolyte IEC 2006 Copyright - all rights reserved No part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. International Electrotechnical Commissi
14、on, 3, rue de Varemb, PO Box 131, CH-1211 Geneva 20, Switzerland Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmailiec.ch Web: www.iec.ch U For price, see current catalogue PRICE CODE Commission Electrotechnique Internationale International Electrotechnical Commission Copyright Int
15、ernational Electrotechnical Commission Provided by IHS under license with IECLicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/10/2007 04:51:21 MSTNo reproduction or networking permitted without license from IHS -,-,- 2 60384-25 IEC:2006(E) CONTENTS FOREWORD.3 1 General 6 1.1 S
16、cope6 1.2 Object .6 1.3 Normative references 6 1.4 Information to be given in a detail specification .7 1.5 Terms and definitions8 1.6 Marking .8 2 Preferred rating and characteristics8 2.1 Preferred characteristics .8 2.2 Preferred values of ratings 9 3 Quality assessment procedures9 3.1 Primary st
17、age of manufacture9 3.2 Structurally similar components.9 3.3 Declaration of conformity (basic requirements).10 3.4 Test schedule and requirement for initial assessment (mandatory and optional tests) .10 3.5 Quality conformance inspection.19 4 Test and measurement procedures.21 4.1 Preliminary dryin
18、g .21 4.2 Measuring conditions 21 4.3 Mounting .21 4.4 Visual examination and check of dimensions.21 4.5 Electrical tests.21 4.6 Resistance to soldering heat .23 4.7 Solderability 24 4.8 Shear test .24 4.9 Substrate bending test 24 4.10 Rapid change of temperature 24 4.11 Climatic sequence.25 4.12 D
19、amp heat, steady state25 4.13 Characteristics at high and low temperature 26 4.14 Surge 26 4.15 Endurance.26 4.16 Storage at high temperature27 4.17 Charge and discharge (if required by the detail specification)27 4.18 Component solvent resistance (if applicable).28 4.19 Solvent resistance of the ma
20、rking (if applicable)28 4.20 High surge current (if applicable).28 Copyright International Electrotechnical Commission Provided by IHS under license with IECLicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/10/2007 04:51:21 MSTNo reproduction or networking permitted without lic
21、ense from IHS -,-,- 60384-25 IEC:2006(E) 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT Part 25: Sectional specification Surface mount fixed aluminium electrolytic capacitors with conductive polymer solid electrolyte FOREWORD 1) The International Elect
22、rotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields.
23、To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC Nat
24、ional Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (
25、ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation
26、 from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot b
27、e held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. A
28、ny divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publi
29、cation. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, prop
30、erty damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in
31、this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any
32、 or all such patent rights. International Standard IEC 60384-25 has been prepared by IEC technical committee 40: Capacitors and resistors for electronic equipment. The text of this standard is based on the following documents: FDIS Report on voting 40/1733/FDIS 40/1756/RVD Full information on the vo
33、ting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. Copyright International Electrotechnical Commission Provided by IHS under license with IECLicensee=IHS Employ
34、ees/1111111001, User=Wing, Bernie Not for Resale, 03/10/2007 04:51:21 MSTNo reproduction or networking permitted without license from IHS -,-,- 4 60384-25 IEC:2006(E) IEC 60384 consists of the following parts, under the general title Fixed capacitors for use in electronic equipment: Part 1: Generic
35、specification Part 2: Sectional specification: Fixed metallized polyethylene-terephthalate film dielectric d.c. capacitors Part 3: Sectional specification: Fixed tantalum chip capacitors Part 4: Sectional specification: Aluminium electrolytic capacitors with solid and non-solid electrolyte Part 5: S
36、ectional specification: Fixed mica delectric d.c. capacitors with a rated voltage not exceeding 3 000 V Selection of methods of test and general requirements Part 6: Sectional specification: Fixed metallized polycarbonate film dielectric d.c. capacitors Part 7: Sectional specification: Fixed polysty
37、rene film dielectric metal foil d.c. capacitors Part 8: Sectional specification: Fixed capacitors of ceramic dielectric, Class 1 Part 9: Sectional specification: Fixed capacitors of ceramic dielectric, Class 2 Part 11: Sectional specification: Fixed polyethylene-terephthalate film dielectric metal f
38、oil d.c. capacitors Part 12: Sectional specification: Fixed polycarbonate film dielectric metal foil d.c. capacitors Part 13: Sectional specification: Fixed polypropylene film dielectric metal foil d.c. capacitors Part 14: Sectional specification: Fixed capacitors for electromagnetic interference su
39、ppression and connection to the supply mains Part 15: Sectional specification: Fixed tantalum capacitors with non-solid or solid electrolyte Part 16: Sectional specification: Fixed metallized polypropylene film dielectric d.c. capacitors Part 17: Sectional specification: Fixed metallized polypropyle
40、ne film dielectric a.c. and pulse capacitors Part 18: Sectional specification: Fixed aluminium electrolytic chip capacitors with solid and non-solid electrolyte Part 19: Sectional specification: Fixed metallized polyethylene-terephthalate film dielectric chip d.c. capacitors Part 20: Sectional speci
41、fication: Fixed metallized polyphenylene sulphide film dielectric chip d.c. capacitors Part 21: Sectional specification: Fixed surface mount multilayer capacitors of ceramic dielectric, Class 1 Part 22: Sectional specification: Fixed surface mount multilayer capacitors of ceramic dielectric, Class 2
42、 Part 23: Sectional specification: Fixed surface mount metallized polyethylene naphthalate film dielectric d.c. capacitors Part 24: Sectional specification: Surface mount fixed tantalum electrolytic capacitors with conductive polymer solid electrolyte Part 25: Sectional specification: Surface mount
43、fixed aluminium electrolyte capacitors with conductive polymer solid electrolyte All sectional specifications mentioned above do have one or more blank detail specifications being a supplementary document, containing requirements for style, layout and minimum content of detail specifications. Copyri
44、ght International Electrotechnical Commission Provided by IHS under license with IECLicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/10/2007 04:51:21 MSTNo reproduction or networking permitted without license from IHS -,-,- 60384-25 IEC:2006(E) 5 The committee has decided that
45、 the contents of this publication will remain unchanged until the maintenance result date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amend
46、ed. A bilingual version of this publication may be issued at a later date. Copyright International Electrotechnical Commission Provided by IHS under license with IECLicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/10/2007 04:51:21 MSTNo reproduction or networking permitted wit
47、hout license from IHS -,-,- 6 60384-25 IEC:2006(E) FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT Part 25: Sectional specification Surface mount fixed aluminium electrolytic capacitors with conductive polymer solid electrolyte 1 General 1.1 Scope This part of IEC 60384 is applicable to aluminium e
48、lectrolytic capacitors with conductive polymer solid electrolyte. These capacitors are primarily intended to be mounted direct on substrates for hybrid circuits or to printed boards. Fixed aluminium electrolytic chip capacitors with solid (MnO2) are not included but are covered by IEC 60384-18. 1.2 Object The object of this standard is to prescribe preferred ratings and characteristics and to select from IEC 60384