《ISO-13457-2000.pdf》由会员分享，可在线阅读，更多相关《ISO-13457-2000.pdf（18页珍藏版）》请在三一文库上搜索。
1、Reference number ISO 13457:2000(E) ISO 2000 INTERNATIONAL STANDARD ISO 13457 First edition 2000-05-01 Agricultural irrigation equipment Water-driven chemical injector pumps Matriel agricole dirrigation Pompes doseuses moteur hydraulique pour linjection de produits chimiques Copyright International O
2、rganization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/20/2007 04:58:34 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 13457:2000(E) PDF disclaimer This PDF file may contain embedded type
3、faces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infri
4、nging Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were opti
5、mized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2000 All rights reserved. Unless otherwise specified, no
6、 part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case posta
7、le 56 ? CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 734 10 79 E-mail copyrightiso.ch Web www.iso.ch Printed in Switzerland ii ISO 2000 All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972
8、545001 Not for Resale, 04/20/2007 04:58:34 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 13457:2000(E) ISO 2000 All rights reservediii ContentsPage Foreword.iv 1Scope 1 2Normative references1 3Terms and definitions .1 4Classification5 4.1Classification according to in
9、stallation type 5 4.2Classification according to mixing ratio .5 5Marking.5 6Technical characteristics6 6.1General6 6.2Materials .6 6.3Connection of a water-driven injector pump to an irrigation system.6 7Mechanical and function tests .7 7.1General7 7.2Sampling and acceptance requirements.7 7.3Test
10、of resistance to pressure8 7.4Test of watertightness of check valves.8 7.5Test of range of working pressure.9 7.6Test of resistance to draining.9 7.7Test of injection rate10 7.8Drive water ratio test .10 7.9Test of injection rate for proportional water-driven injector pump10 7.10Test of head loss fo
11、r in-line water-driven injector pump.11 8Durability 11 9Information to be supplied by the manufacturer12 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/20/2007 04:58:34 MDTNo reproducti
12、on or networking permitted without license from IHS -,-,- ISO 13457:2000(E) iv ISO 2000 All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is n
13、ormally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part i
14、n the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. Draft International Standards adopted by the tec
15、hnical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of pate
16、nt rights. ISO shall not be held responsible for identifying any or all such patent rights. International Standard ISO 13457 was prepared by Technical Committee ISO/TC 23,Tractors and machinery for agriculture and forestry, Subcommittee SC 18,Irrigation and drainage equipment and systems. Copyright
17、International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/20/2007 04:58:34 MDTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARDISO 13457:2000(E) ISO 2000 All righ
18、ts reserved1 Agricultural irrigation equipment Water-driven chemical injector pumps 1Scope This International Standard specifies construction and operational requirements and test methods for water-driven chemical injector pumps, referred to hereinafter as water-driven injector pumps. These water-dr
19、iven injector pumps are used to inject chemicals into irrigation systems. The chemicals include liquid fertilisers and solutions of fertilisers and other soluble agricultural chemicals such as acids, pesticides and herbicides. This International Standard is applicable to water-driven injector pumps
20、which are intended to operate at water temperatures of up to 50 C and with the types and concentrations of chemicals routinely applied in irrigation. It is not applicable to backflow prevention devices (which are not an integral part of a water-driven injector pump), nor to Venturi-principle water-d
21、riven devices for injecting chemicals into an irrigation system. 2Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this International Standard. For dated references, subsequent amendments to, or revisions of, an
22、y of these publications do not apply. However, parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative documen
23、t referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 7-1:1994,Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation. ISO 2859-1:1999,Sampling procedures for inspection by attributes
24、Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection. ISO 7005-1:1992,Metallic flanges Part 1: Steel flanges. ISO 7005-2:1988,Metallic flanges Part 2: Cast iron flanges. ISO 7714:1),Agricultural irrigation equipment Volumetric valves General requirements and t
25、est methods. 3Terms and definitions For the purposes of this International Standard, the following terms and definitions apply. 1)To be published. (Revision of ISO 7714:1995) Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Stand
26、ards 1/9972545001 Not for Resale, 04/20/2007 04:58:34 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 13457:2000(E) 2 ISO 2000 All rights reserved 3.1 water-driven injector pump water-driven chemical injector pump hydraulic pump intended to inject chemicals into an irri
27、gation system, operated exclusively by the energy of irrigation water driving a hydraulic device such as a piston or turbine 3.2 nominal size conventional numerical designation used to define the nominal size of the device for connecting the water-driven injector pump to the irrigation system, by me
28、ans of threads, flanges or other connecting devices NOTEThis designation is used to define the size of an in-line water-driven injector pump 3.3 minimum working pressure pmin lowest pressure declared by the manufacturer at the inlet of a water-driven injector pump at which the water-driven injector
29、pump functions properly 3.4 maximum working pressure pmax highest pressure declared by the manufacturer at the inlet of a water-driven injector pump at which the water-driven injector pump functions properly 3.5 range of working pressure pressure range between the minimum working pressure pminand th
30、e maximum working pressure pmax 3.6 drive water irrigation water used to operate an on-line water-driven injector pump NOTEThe drive water may be ejected from the water-driven injector pump or may be returned to the irrigation system. 3.7 drive water ratio ratio of one unit volume of injected chemic
31、als to the volume of drive water required to inject the same unit volume of chemical solution EXAMPLE1:2 or 1:3 3.8 irrigation water flow rate rate of flow of irrigation water through irrigation pipeline which is serviced by the water-driven injector pump 3.9 injection rate pumping rate rate of flow
32、 of chemical solution injected into an irrigation system during operation of a water-driven injector pump 3.10 chemical liquid fertilisers and solutions of fertilisers and other soluble agricultural chemicals such as acids, pesticides and herbicides used in agriculture in liquid, solution or water s
33、oluble form, normally applied through or otherwise injected into irrigation systems Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/20/2007 04:58:34 MDTNo reproduction or networking perm
34、itted without license from IHS -,-,- ISO 13457:2000(E) ISO 2000 All rights reserved3 3.11 chemical solution water in which one or several types of chemicals have been dissolved or diluted 3.12 irrigation system water flow rate sum of the irrigation water flow rate and the injection rate 3.13 mixing
35、ratio ratio of the injection rate to the irrigation system water flow rate EXAMPLEAn injection rate of 1 l/h into an irrigation water flow rate of 199 l/h gives an irrigation system water flow rate of 200 l/h, and a mixing ratio of 1:200. 3.14 pulse volume stroke volume volume of chemical solution i
36、njected into an irrigation system in one water-driven injector pump cycle EXAMPLEOne stroke in a piston or membrane activated water-driven injector pump. 3.15 proportional water-driven injector pump proportional water-driven chemical injector pump water-driven injector pump intended to maintain a re
37、latively constant mixing ratio throughout the period of its operation at the irrigation water flow rates declared by the manufacturer 3.16 in-line water-driven injector pump in-line water-driven chemical injector pump water-driven injector pump installed in the main irrigation system piping or in by
38、pass piping and featuring three ports including: ?one inlet for chemicals, ?one inlet for irrigation water, ?one outlet for irrigation water with chemicals injected See Figure 1. NOTEThe injection of a chemical occurs inside the water-driven injector pump. Copyright International Organization for St
39、andardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/20/2007 04:58:34 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 13457:2000(E) 4 ISO 2000 All rights reserved a) In-line full flowb) In-line bypass Key
40、 1Injector pump 2Irrigation flow 3Irrigation water with injected chemicals 4Chemicals Figure 1 In-line water-driven injector pump 3.17 on-line water-driven injector pump on-line water-driven chemical injector pump water-driven injector pump installed off the main irrigation system piping and featuri
41、ng four ports: ?one inlet for chemicals, ?one outlet for chemicals, ?one inlet for drive water, ?one outlet for drive water See Figure 2. NOTEThe injection of a chemical into the irrigation water occurs outside the water-driven injector pump. The outlet for the chemical is intended to be connected t
42、o the main irrigation system piping. The drive water from the drive water outlet cannot be returned to the main irrigation system piping. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/
43、20/2007 04:58:34 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 13457:2000(E) ISO 2000 All rights reserved5 Key 1Injector pump 2Drive water 3Chemicals 4Irrigation flow 5Irrigation water with injected chemicals Figure 2 On-line water-driven injector pump 3.18 chemical s
44、torage tank container for storing chemicals and supplying them to a water-driven injector pump 4Classification 4.1Classification according to installation type 4.1.1In-line water-driven injector pump 4.1.1.1Full flow installation 4.1.1.2Bypass flow installation 4.1.2On-line water-driven injector pum
45、p 4.2Classification according to mixing ratio 4.2.1Proportional water-driven injector pump 4.2.1.1Fixed mixing ratio 4.2.1.2Adjustable mixing ratio 4.2.2Non-proportional water-driven injector pump 5Marking The water-driven injector pump shall bear a clear, legible and durable marking which shall giv
46、e the following particulars: a)name of manufacturer or the manufacturers trade mark; Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/20/2007 04:58:34 MDTNo reproduction or networking per
47、mitted without license from IHS -,-,- ISO 13457:2000(E) 6 ISO 2000 All rights reserved b)nominal size; c)maximum and minimum working pressures; d)maximum and minimum irrigation water flow rates; e)injection rate; f)maximum injection rate; g)model number identical with that given in the manufacturers
48、 catalogue; h)year of production or a mark which identifies the production series; i)arrows indicating the direction of flow of water and chemicals into and out of the water-driven injector pump. 6Technical characteristics 6.1General The water-driven injector pump shall employ means, such as a vacuum breaker valve, to prevent emptying of the chemical storage tank to the irrigation system through the water-driven injector pump in the