《BS-6955-15-1994 ISO-5347-15-1993.pdf》由会员分享，可在线阅读，更多相关《BS-6955-15-1994 ISO-5347-15-1993.pdf（6页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS 6955-15: 1994 ISO 5347-15: 1993 Calibration of vibration and shock pick-ups Part 15: Method of test for acoustic sensitivity UDC 534.1:681.327.7:53.089.6 Licensed Copy: sheffieldun sheffieldun, na, Tue Dec 05 05:16:35 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 6955-15:1994 Thi
2、s British Standard, having been prepared under the direction of the General Mechanical Engineering Standards Policy Committee, was published under the authority of the Standards Board and comes into effect on 15 March 1994 BSI 11-1999 The following BSI references relate to the work on this standard:
3、 Committee reference GME/21 Draft for comment 87/72304 DC ISBN 0 580 23087 2 Committees responsible for this British Standard The preparation of this British Standard was entrusted by the General Mechanical Engineering Standards Policy Committee (GME/-) to Technical Committee GME/21, upon which the
4、following bodies were represented: Electricity Association Federation of Civil Engineering Contractors Imperial College of Science and Technology Institute of Sound and Vibration Research Institution of Mechanical Engineers Lloyds Register of Shipping Ministry of Defence Open University Power Genera
5、tion Contractors Association PGCA (BEAMA Ltd.) Railway Industry Association of Great Britain Sira Test and Certification Ltd. Society of British Aerospace Companies Limited The following bodies were also represented in the drafting of the standard, through subcommittees and panels: British Coal Corp
6、oration Health and Safety Executive Society of Environmental Engineers University of Cranfield Amendments issued since publication Amd. No.DateComments Licensed Copy: sheffieldun sheffieldun, na, Tue Dec 05 05:16:35 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 6955-15:1994 BSI 11-1999i Contents Pag
7、e Committees responsibleInside front cover National forewordii 1Scope1 2Apparatus1 3Method1 Licensed Copy: sheffieldun sheffieldun, na, Tue Dec 05 05:16:35 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 6955-15:1994 ii BSI 11-1999 National foreword This Part of BS 6955 has been prepared under the dir
8、ection of the General Mechanical Engineering Standards Policy Committee. It is identical with ISO 5347-15:1993 Methods for the calibration of vibration and shock pick-ups Part 15: Testing of acoustic sensitivity, published by the International Organization for Standardization (ISO). ISO 5347-15 was
9、prepared by Technical Committee ISO/TC 108, Mechanical vibration and shock, in which the UK played an active part. BS 6955 consists of the following Parts, which are identical with the corresponding Parts of ISO 5347: Part 0: Guide to basic principles; Part 1: Methods for primary vibration calibrati
10、on by laser interferometry; Part 2: Method for primary shock calibration by light cutting; Part 3: Method for secondary vibration calibration; Part 4: Method for secondary shock calibration; Part 5: Method for calibration by Earths gravitation; Part 6:Method for primary vibration calibration at low
11、frequencies; Part 7: Methods for primary calibration by centrifuge; Part 8: Method for primary calibration by dual centrifuge; Part 9: Method for secondary vibration calibration by comparison of phase angles; Part 10: Method for primary calibration by high impact shocks; Part 11: Method of test for
12、transverse vibration sensitivity; Part 12: Method of test for transverse shock sensitivity; Part 13: Method of test for base strain sensitivity; Part 14: Method of test for resonance frequency of undamped accelerometers on a steel block; Part 15: Method of test for acoustic sensitivity; Part 16: Met
13、hod of test for mounting torque sensitivity; Part 17: Method of test for fixed temperature sensitivity; Part 18: Method of test for transient temperature sensitivity; Part 19: Method of test for magnetic field sensitivity. Part 20 of ISO 5347 is in preparation. It is envisaged that when it is publis
14、hed it will be implemented as Part 20 of BS 6955. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obli
15、gations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, page 1 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Lice
16、nsed Copy: sheffieldun sheffieldun, na, Tue Dec 05 05:16:35 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 6955-15:1994 BSI 11-19991 1 Scope ISO 5347 comprises a series of documents dealing with methods for the calibration of vibration and shock pick-ups. This part of ISO 5347 lays down detailed spec
17、ifications for the instrumentation and procedure to be used for acoustic sensitivity testing. It applies to accelerometers. This part of ISO 5347 is applicable for a frequency range of random noise from 125 Hz to 8 000 Hz and a sound pressure level of 130 dB (reference value: 2 105Pa). 2 Apparatus 2
18、.1 Equipment capable of maintaining room temperature at 23 C 3 C. 2.2 Room, having a volume of at least 75 m3 so as to obtain approximate free-field conditions. 2.3 Random noise generator, low-pass filter or equalizer, amplifier and loudspeaker, which can produce a free-field random noise with a tot
19、al sound pressure level of 130 dB 5 dB (reference value: 2 105Pa) with the following spectrum shape per frequency octave band: 125 Hz: 115 dB 6 dB; 250 Hz to 2 000 Hz: 120 dB 5 dB; 4 000 Hz: 115 dB 6 dB; 8 000 Hz: 105 dB 10 dB. NOTE 1A 0,5 mH and 1 4F low-pass filter, a commercial 30 W power amplifi
20、er and an 8 in, 50 W broadband loudspeaker in a 1 m 1 m baffle is recommended. Distance from the loudspeaker to the accelerometer: 50 mm to 100 mm. 2.4 Sound level measuring equipment with octave band filtering, covering the range from 80 dB to 140 dB (reference value: 2 105Pa) and with uncertainty
21、maximum 3 dB. 3 Method 3.1 Test procedure Place the loudspeaker in the middle of the room with no hard reflecting surfaces in front of it. Suspend the accelerometer in a rubber harness in front of and close to the loudspeaker. The suspension resonance frequency shall be lower than 20 Hz. Rotate the
22、accelerometer in order to find maximum sensitivity. Replace the accelerometer by a microphone and shape the noise spectrum. After the accelerometer has been suspended in its rubber harness and then rotated, measure the maximum output, in metres per second squared, for the specified sound pressure le
23、vel. If it is suspected that whole accelerometer rigid body vibrations are induced and that this affects the accelerometer output, special test procedures, outlined in 3.3, shall be carried out and reported. 3.2 Expression of results The acoustic sensitivity shall be reported as the equivalent accel
24、erometer output, in metres per second squared, for the applied level sound pressure (reference value: 2 105Pa). 3.3 Special test procedures Acoustic sensitivity measurements of piezoelectric accelerometers can be difficult to make because whole rigid body vibratory motion effects can be induced into
25、 the accelerometer. If these effects are suspected, the following methods for minimizing motion effects shall be applied: a) Mount the accelerometer on a very heavy but small fixture; this generally distorts the acoustic field so the sound pressure level has to be measured with the microphone in an
26、accelerometer dummy mounted on the fixture. b) Measure the induced motion with an accelerometer that is protected and mounted inside the fixture and subtract the induced motion components from the pick-up output. c) Mount the accelerometer on the smallest possible rod fixture clamped to a heavy base
27、 and isolate this fixture and the base from the sound field; a high density material, e.g. tungsten, is recommended. Licensed Copy: sheffieldun sheffieldun, na, Tue Dec 05 05:16:35 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 6955-15: 1994 ISO 5347-15: 1993 BSI 389 Chiswick High Road London W4 4AL
28、BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Us
29、ers of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secre
30、tary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buyi
31、ng standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published a
32、s British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which g
33、ive details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefi
34、ts contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents A
35、ct 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary deta
36、ils such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070. Licensed Copy: sheffieldun sheffieldun, na, Tue Dec 05 05:16:35 GMT+00:00 2006, Uncontrolled Copy, (c) BSI