《ISO-15854-2005.pdf》由会员分享，可在线阅读，更多相关《ISO-15854-2005.pdf（20页珍藏版）》请在三一文库上搜索。
1、 Reference number ISO 15854:2005(E) ISO 2005 INTERNATIONAL STANDARD ISO 15854 First edition 2005-07-15 Dentistry Casting and baseplate waxes Art dentaire Cires pour coule et pour plaque de base Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=N
2、ASA Technical Standards 1/9972545001 Not for Resale, 04/19/2007 19:52:26 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15854:2005(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or vi
3、ewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability i
4、n this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable
5、 for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2005 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any mea
6、ns, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyr
7、ightiso.org Web www.iso.org Published in Switzerland ii ISO 2005 All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/19/2007 19:52:26 MDTNo reproduction or networking per
8、mitted without license from IHS -,-,- ISO 15854:2005(E) ISO 2005 All rights reserved iii Contents Page Foreword iv Introduction v 1 Scope 1 2 Normative references1 3 Terms and definitions .1 4 Classification2 5 Requirements.2 5.1 Appearance 2 5.2 Flow.2 5.3 Behaviour on trimming .2 5.4 Behaviour on
9、softening (Type 1)3 5.5 Appearance after flaming (Type 2).3 5.6 Behaviour on softening (Type 2)3 5.7 Residue on artificial teeth (Type 2)3 5.8 Behaviour of colouring material (Type 2)3 5.9 Adhesion on storage (Type 2)3 5.10 Residue on ignition (Type 1).3 5.11 Biocompatibility.3 6 Sampling.3 7 Test m
10、ethods General 3 7.1 Ambient temperature.3 7.2 Apparatus function verification4 8 Test methods Specific4 8.1 Visual inspection .4 8.2 Flow.4 8.3 Behaviour on trimming .8 8.4 Behaviour on softening (Type 1)8 8.5 Appearance after flaming (Type 2).8 8.6 Behaviour on softening (Type 2)8 8.7 Residue on a
11、rtificial teeth and behaviour of colouring material (Type 2)8 8.8 Adhesion on storage (Type 2)10 8.9 Residue on ignition (Type 1).10 9 Marking and packaging.11 9.1 Marking.11 9.2 Packaging.11 Bibliography12 Copyright International Organization for Standardization Provided by IHS under license with I
12、SO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/19/2007 19:52:26 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15854:2005(E) iv ISO 2005 All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federatio
13、n of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee.
14、 International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance wi
15、th the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires appro
16、val by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 15854 was prepared by Technical Committ
17、ee ISO/TC 106, Dentistry, Subcommittee SC 2, Prosthodontic materials. This first edition cancels and replaces ISO 1561:1995 and ISO 12163:1999, which have been technically revised. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical
18、 Standards 1/9972545001 Not for Resale, 04/19/2007 19:52:26 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15854:2005(E) ISO 2005 All rights reserved v Introduction This International Standard does not include specific and quantitative requirements for freedom from bio
19、logical hazards. It is recommended that, in assessing possible biological or toxicological hazards, reference be made to ISO 7405 and ISO 10993-1 (see Bibliography). Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/99
20、72545001 Not for Resale, 04/19/2007 19:52:26 MDTNo reproduction or networking permitted without license from IHS -,-,- Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/19/2007 19:52:26 MD
21、TNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARD ISO 15854:2005(E) ISO 2005 All rights reserved 1 Dentistry Casting and baseplate waxes 1 Scope This International Standard is applicable to dental casting wax and to dental baseplate wax. It specifies the
22、classification of, and requirements for, dental casting wax and baseplate wax together with the test methods to be employed to determine compliance with these requirements. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated ref
23、erences, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 1942-2, Dental vocabulary Part 2: Dental materials ISO 3336, Dentistry Synthetic polymer teeth1) ISO 4824, Dentistry Ceramic denture teeth1) ISO 6873
24、, Dental gypsum products ISO 8601, Data elements and interchange formats Information interchange Representation of dates and times 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 1942-2 and the following apply. 3.1 casting wax mouldable material prim
25、arily for shaping patterns in the production of fixed cast restorations using the “lost-wax” procedure 3.2 baseplate wax mouldable material primarily for shaping patterns that will be duplicated in denture base polymers, and for forming occlusion rims and other patterns 1) ISO 3336 and ISO 4824 are
26、to be combined and revised as ISO 22112, Dentistry Artificial teeth for dental prostheses. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/19/2007 19:52:26 MDTNo reproduction or networki
27、ng permitted without license from IHS -,-,- ISO 15854:2005(E) 2 ISO 2005 All rights reserved 4 Classification Dental waxes covered by this International Standard are classified according to the flow characteristics that represent their hardness, as follows: a) Type 1 (casting wax): 1) Class 1 Soft 2
28、) Class 2 Hard b) Type 2 (baseplate wax): 1) Class 1 Soft 2) Class 2 Hard 3) Class 3 Extra hard 5 Requirements 5.1 Appearance The wax shall be uniform in colour, supplied in pieces of uniform size, of smooth texture and free of foreign materials. Test in accordance with 8.1. 5.2 Flow The samples of
29、the wax when tested in accordance with 8.2 shall have flow properties complying with the requirements in Table 1. Table 1 Flow requirements Type 1 Casting wax Type 2 Baseplate wax Class 1 Class 2 Class 1 Class 2 Class 3 Temperature Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. C % % % % % % % %
30、% % 23,0 0,1 1,0 0,6 0,2 30,0 0,1 1,0 37,0 0,1 1,0 5,0 90,0 10,0 1,2 40,0 0,1 50,0 20,0 45,0 0,1 70,0 90,0 70,0 90,0 50,0 90,0 5,0 50,0 Undefined. 5.3 Behaviour on trimming The wax shall be capable of being trimmed without chipping, flaking or tearing when tested in accordance with 8.3. Copyright In
31、ternational Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/19/2007 19:52:26 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15854:2005(E) ISO 2005 All rights reserved 3 5.4 Behavi
32、our on softening (Type 1) The wax shall soften without flaking or crumbling and shall cohere readily when tested in accordance with 8.4. 5.5 Appearance after flaming (Type 2) The wax shall present a smooth glossy surface when tested in accordance with 8.5. 5.6 Behaviour on softening (Type 2) The wax
33、 shall soften without becoming sticky or crumbly and shall be mouldable without breaking or laminating when tested in accordance with 8.6. 5.7 Residue on artificial teeth (Type 2) The wax shall not leave a residue on either ceramic or plastic teeth when tested in accordance with 8.7. 5.8 Behaviour o
34、f colouring material (Type 2) The colouring material shall neither separate from the wax nor impregnate the gypsum mould when tested in accordance with 8.7. 5.9 Adhesion on storage (Type 2) Self-adhesion during storage of the wax shall be such that when tested in accordance with 8.8, there shall be
35、no evidence of damage to wax surfaces that have been in contact with either wax or paper. Where separating paper is used, the wax and paper surfaces shall separate cleanly and readily. 5.10 Residue on ignition (Type 1) If the manufacturer does not state a value for the residue on ignition, the solid
36、 residue of the wax, as determined in accordance with 8.9, shall be no greater than 0,1 %. If the manufacturer states a value for the residue on ignition, the solid residue of the wax, as determined in accordance with 8.9, shall not differ by more than 20 % from that value. 5.11 Biocompatibility See
37、 ISO 7405 and ISO 10993-1 for guidance on compatibility. 6 Sampling The amount of material procured for testing shall be at least 250 g for Type 1, or 500 g for Type 2, and from one batch. 7 Test methods General 7.1 Ambient temperature Unless otherwise specified in this International Standard, all s
38、pecimen preparation and testing shall be conducted at an ambient temperature of (23 2) C. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/19/2007 19:52:26 MDTNo reproduction or networkin
39、g permitted without license from IHS -,-,- ISO 15854:2005(E) 4 ISO 2005 All rights reserved 7.2 Apparatus function verification All accessories, instruments and equipment shall be examined before use to ensure that they are in acceptable working order, appropriately calibrated and complying with spe
40、cifications stated for them in this International Standard. 8 Test methods Specific 8.1 Visual inspection Carry out visual inspection at nominally normal visual acuity and without magnification. 8.2 Flow 8.2.1 Apparatus 8.2.1.1 Micrometer screw gauge For measuring specimen length, use a micrometer s
41、crew gauge with a range of at least 10 mm, being accurate to 0,005 mm or better. 8.2.1.2 Flow-testing instrument Use a flow-testing instrument, such as the one shown in Figure 1, consisting of the following components: metallic cylindrical weight (item 1 in Figure 1); plastic or hard rubber shaft (i
42、tem 2 in Figure 1); brass plate (item 3 in Figure 1); measuring dial gauge (item 4 in Figure 1), with a range of at least 10 mm, accurate to 0,005 mm or better, and rigidly supported (optional); locking screw (item 5 in Figure 1) (optional). The total mass of the components of items 1, 2 and 3 shall
43、 be such as to provide an axial compressive force of (19,6 0,1) N. The weight (1) shall be separated a minimum distance of 76 mm from the brass plate (3) by the shaft (2). The diameter of the brass plate (3) shall be no less than 50 mm and the thickness no greater than 6,5 mm. The optional dial gaug
44、e (4) and locking screw (5) may replace the micrometer screw gauge for direct measurement (8.2.3). 8.2.1.3 Pouring pan For melting the wax, use a metal or porcelain pan with handle similar to the example shown in Figure 2. 8.2.1.4 Infrared lamp For heating the wax, use an infrared lamp with nominal
45、power of 250 W. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/19/2007 19:52:26 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15854:2005(E) ISO 2005 All
46、rights reserved 5 Key 1 weight 2 shaft 3 brass plate 4 gauge 5 locking screw Figure 1 Flow-testing instrument Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/19/2007 19:52:26 MDTNo repro
47、duction or networking permitted without license from IHS -,-,- ISO 15854:2005(E) 6 ISO 2005 All rights reserved Figure 2 Example of pouring pan Dimensions in millimetres Figure 3 Mould for forming flow specimens 8.2.1.5 Mould For forming the specimens, use a mould as shown in Figure 3, consisting of a flat stainless steel plate, (6,0 0,1) mm thick, with parallel top and bottom surfaces. The plate shall have four holes (10,0 0,1) mm in diameter, with the axes of the holes perpendicular to the surface of the plate. The sides of the