《ISO-20860-1-2008.pdf》由会员分享，可在线阅读，更多相关《ISO-20860-1-2008.pdf（18页珍藏版）》请在三一文库上搜索。
1、 Reference number ISO 20860-1:2008(E) ISO 2008 INTERNATIONAL STANDARD ISO 20860-1 First edition 2008-10-15 Road vehicles 50 impedance radio frequency connection system interface Part 1: Dimensions and electrical requirements Vhicules routiers Interface de systme de connexion de frquence radio de 50
2、Partie 1: Dimensions et exigences lectriques Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 01/29/2009 23:27:42 MSTNo reproduction or networking permitted without license from IHS -,-,- ISO 20860-1:2008(E)
3、 PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file,
4、 parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info rela
5、tive to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYR
6、IGHT PROTECTED DOCUMENT ISO 2008 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below
7、or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2008 All rights reserved Copyright International Organization for Standardi
8、zation Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 01/29/2009 23:27:42 MSTNo reproduction or networking permitted without license from IHS -,-,- ISO 20860-1:2008(E) ISO 2008 All rights reserved iii Contents Page Foreword iv 1 Scope . 1 2 Normative references.
9、 1 3 Terms and definitions. 1 4 Dimensions and coding . 2 4.1 General. 2 4.2 Male connector 2 4.3 Female connector. 2 4.4 Coding ribs 2 4.5 Mechanical and colour codings of the connection system 2 4.6 Multiple interfaces 2 5 Designations . 9 6 Characteristic values 9 7 Test procedures 11 Bibliograph
10、y. 12 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 01/29/2009 23:27:42 MSTNo reproduction or networking permitted without license from IHS -,-,- ISO 20860-1:2008(E) iv ISO 2008 All rights reserved Forewo
11、rd ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technic
12、al committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of el
13、ectrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to t
14、he member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for id
15、entifying any or all such patent rights. ISO 20860-1 was prepared by Technical Committee ISO/TC 22, Road vehicles. ISO 20860 consists of the following parts, under the general title Road vehicles 50 impedance radio frequency connection system interface: Part 1: Dimensions and electrical requirements
16、 Part 2: Test procedures Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 01/29/2009 23:27:42 MSTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARD ISO 20860-1:2008
17、(E) ISO 2008 All rights reserved 1 Road vehicles 50 impedance radio frequency connection system interface Part 1: Dimensions and electrical requirements 1 Scope This part of ISO 20860 specifies male and female connectors of the 50 impedance system interface for radio frequency applications in road v
18、ehicles, and ensures communication to and within road vehicles. It specifies dimensional and electrical requirements and characteristics required for interchange ability. This connection system can be applied in all relevant equipment and cable connections of road vehicles. 2 Normative references Th
19、e following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 20860-2, Road vehicles 50 impedance radio frequ
20、ency connection system interface Part 2: Test procedures 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 male contact pin contact contact intended to make electrical engagement on its outer surface and which will enter a female contact (socke
21、t) 3.2 female contact socket contact contact intended to make electrical engagement on its inner surface and which will accept entry of a male contact (pin) 3.3 male connector pin connector connector containing a male centre contact Copyright International Organization for Standardization Provided b
22、y IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 01/29/2009 23:27:42 MSTNo reproduction or networking permitted without license from IHS -,-,- ISO 20860-1:2008(E) 2 ISO 2008 All rights reserved 3.4 female contact socket connector connector containing a female centre contact
23、 4 Dimensions and coding 4.1 General Unspecified details shall be shown as required in accordance with the characteristics defined in Clause 6. 4.2 Male connector The dimension of the cable connector (CC) and the connector on apparatus (CoA) of the 50 connection system shall conform to Figures 1, 2
24、and 3. 4.3 Female connector The dimensions of the female cable connectors (FCC) for use with the male connectors in accordance with 4.2, shall conform to Figures 4 and 5. 4.4 Coding ribs The dimensions and denominations of the coding ribs shall be in accordance with Figure 6. 4.5 Mechanical and colo
25、ur codings of the connection system The male connector of the 50 connection system allows the use of the mechanical coding options, by applying the coding ribs specified in Figure 6 and their arrangement according to Figure 7 and Table 1. The mechanical design of the female connector shall consider
26、the codings, the locking mechanism and the guide tube on the male connector. 4.6 Multiple interfaces Applications for multiple connectors of the 50 connection system are shown in Figures 8 and 9. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee
27、=Boeing Co/5910770001 Not for Resale, 01/29/2009 23:27:42 MSTNo reproduction or networking permitted without license from IHS -,-,- ISO 20860-1:2008(E) ISO 2008 All rights reserved 3 Dimensions in millimetres Key 1 reference plane 2 coding ribs (dimensions according to Figure 6) 3 locking nose NOTE
28、For Section AA, see Figure 2. Figure 1 Male connector dimensions Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 01/29/2009 23:27:42 MSTNo reproduction or networking permitted without license from IHS -,-,-
29、 ISO 20860-1:2008(E) 4 ISO 2008 All rights reserved Dimensions in millimetres a) Cable connector (CC) Key 1 reference plane a Centre contact: see detail X. b Dielectric: see detail X. c Dielectric insulation does not exceed the foremost plane of the outer conductor. d No burrs, no sharp edges. b) Op
30、tional connector on apparatus (CA opt) NOTE For details X and Y, see Figure 3. Figure 2 Section AA of the male connector Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 01/29/2009 23:27:42 MSTNo reproductio
31、n or networking permitted without license from IHS -,-,- ISO 20860-1:2008(E) ISO 2008 All rights reserved 5 Dimensions in millimetres Figure 3 Details X and Y of Figure 2 Dimensions in millimetres Key 1 reference plan Figure 4 Female cable connector (FCC) Copyright International Organization for Sta
32、ndardization Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 01/29/2009 23:27:42 MSTNo reproduction or networking permitted without license from IHS -,-,- ISO 20860-1:2008(E) 6 ISO 2008 All rights reserved Dimensions in millimetres a The catch circle is coaxially
33、 arranged to reference datum axis D (geometrically ideal). (See Figure 4.) Figure 5 Arrangement of the catch circle Dimensions in millimetres a) Coding ribs a, b1, b2, c and d b) Coding ribs g1, h, j1 and j2 Figure 6 Dimensions and denominations of coding ribs Copyright International Organization fo
34、r Standardization Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 01/29/2009 23:27:42 MSTNo reproduction or networking permitted without license from IHS -,-,- ISO 20860-1:2008(E) ISO 2008 All rights reserved 7 Figure 7 Mechanical codings of single-pole 50 connec
35、tion system Table 1 Mechanical and colour codings Coding Combinations of coding ribs Colour Similar colour RAL number a A a b1 Deep black 9005 B a b2 Cream white 9001 C a c Signal blue 5005 D a d Bordeaux violet 4004 E b1 b2 Leaf green 6002 F b1 c Brown 8011 G b1 d Blue grey 7031 H b2 c Violet 4003
36、I b2 c Beige 1001 K c d Curry yellow 1027 L h j1 Carmine red 3002 M h j2 Pastel orange 2003 N h g1 Pastel green 6019 a See Bibliography 1. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 01/29/2009 23:27:42
37、 MSTNo reproduction or networking permitted without license from IHS -,-,- ISO 20860-1:2008(E) 8 ISO 2008 All rights reserved Dimensions in millimetres Figure 8 Dual male connector (DC) Type X Dimensions in millimetres Figure 9 Male connector Type Y Copyright International Organization for Standardi
38、zation Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 01/29/2009 23:27:42 MSTNo reproduction or networking permitted without license from IHS -,-,- ISO 20860-1:2008(E) ISO 2008 All rights reserved 9 5 Designations Designations for a single male cable connector (
39、CC), coding H: Cable connector ISO 20860 CC H Designation for an optional connector on apparatus (CA opt), coding A: Connector on apparatus ISO 20860 CA opt A Designation for a female cable connector (FCC), coding C: Female cable connector ISO 20860 FCC C Designation for a dual male connector Type X
40、 (DC): Dual male connector ISO 20860 XDMC Designation for a Type Y male connector: Dual male connector ISO 20860 YDMC 6 Characteristic values The 50 connection system in accordance with this part of ISO 20860 shall meet the characteristic values specified in Tables 2, 3 and 4. Table 2 Electrical per
41、formance characteristics of the coaxial interface Nomination Specification value Frequency range 0 Ghz to 4 GHz Nominal characteristic impedance 50 Return loss Key 1 restricted area for measurement X frequency, in Mhz Y return loss, in dB Z VSWR Copyright International Organization for Standardizati
42、on Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 01/29/2009 23:27:42 MSTNo reproduction or networking permitted without license from IHS -,-,- ISO 20860-1:2008(E) 10 ISO 2008 All rights reserved Table 2 (continued) Nomination Specification value Insertion loss
43、For each pair of connector Key 1 restricted area for measurement X frequency, in Mhz Y return loss, in dB Shielding effectiveness Key X frequency, in Mhz Y return loss, in dB Insulation resistance W 1 000 M before, and W 500 M after strain Centre contact resistance u 5 m before, and u 40 m after 25
44、matings Outer contact resistance u 5 m before, and u 40 m after 25 matings Dielectric withstanding voltage 500 V minimum Working voltage u 60 V d.c. Working current u 1 A d.c. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Boeing Co/591077000
45、1 Not for Resale, 01/29/2009 23:27:42 MSTNo reproduction or networking permitted without license from IHS -,-,- ISO 20860-1:2008(E) ISO 2008 All rights reserved 11 Table 3 Mechanical performance characteristics Nomination Specification value a Connection insertion force u 25 N Connection extraction
46、force u 25 N Locking device strength W 80 N Cable strain relief in axial direction W 100 N Gauge retention force centre contact W 0,28 N Gauge retention force outer contact W 2 N Mating cycles 25 cycles minimum Outer contact retention force in housing W 100 N a Values are valid for single connectors
47、. Table 4 Material and coating characteristics Nomination Specification value Material of coating ? contact zone of centre conductor Au Material of coating ? contact zone of outer conductor Ni or Sn 7 Test procedures Test procedures to verify conformance with the requirements given in Clause 6 shall be performed in accordance with ISO 20860-2. Copyright International Organization for Standardiza