《ISO-603-12-1999.pdf》由会员分享，可在线阅读，更多相关《ISO-603-12-1999.pdf（12页珍藏版）》请在三一文库上搜索。
1、STD-ISO b03-12-ENGL 1979 4851903 080qOqo 427 INTERNATIONAL STANDARD IS0 603-1 : I 999 IS0 603-2:1999 IS0 603-31999 IS0 603-4:1999 IS0 603-511 999 IS0 603-61999 IS0 603-7:1999 IS0 603-8:1999 IS0 603-91999 IS0 603-1 0:1999 IS0 603-1 1 1999 IS0 603-1 21999 IS0 603-1 31999 IS0 603-1 41999 IS0 603-1 5199
2、9 IS0 603-1 61999 This material is reproduccd from IS0 documents under International Organization for Standardization (ISO) Copyright License Number HlS/CC/1996. Not for resale. No part of these IS0 documents may be reproduced in any form, electronic retrieval system or otherwise, except as allowed
3、in the copyright law of the country of use, or with the prior written consent of IS0 (Case postale 56,121 1 Geneva 20, Switzerland Fax +41 22 734 IO 79), IHS or the IS0 Licensors members. TECHNICAL CORRIGENDUM 1 Published 1999-1 1-15 INTERNATIONAL ORGANIZATION FOR STANDARDIZATION * MDIQYHAPOAHAFI OP
4、rAHIIJAL 200 2 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Aramco HQ/9980755100 Not for Resale, 04/23/2007 09:27:08 MDTNo reproduction or networking permitted without license from IHS -,-,- o IS0 STD-IS0 b03-12-ENGL 1999 I 4851903 0790131
5、455 IS0 603-1 2:1999(E) 3.2 Type 4: Wheel tapered on both sides See Figure 2 and Table 2. L 1:16 1 - I Figure 2 - Type 4 Table 2 - Dimensions of Type 4 20 3 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Aramco HQ/9980755100 Not for Resale, 0
6、4/23/2007 09:27:08 MDTNo reproduction or networking permitted without license from IHS -,-,- STDmISO b03-32-ENGL 3999 4851903 0790332 393 = IS0 603-1 2:1999( E) Q IS0 3.3 Type 16: Cylindrical plug, tapered cone 3.5 Type 18R: Cylindrical plug, round end See Figure 3 and Table 3. See Figure 5 and Tabl
7、e 3. 3.4 Type 18: Cylindrical plug, flat end See Figure 4 and Table 3 . SI 3.6 Type 19: Cylindrical plug, taper-roll shaped See Figure 6 and Table 3. Figure 3 - Type 16 Figure 4 - Type 18 Figure 5 - Type 18R Figure 6 - Type 19 Table 3 - Dimensions of Type 16, Type 18, Type 18R and Type 19 4 Copyrigh
8、t International Organization for Standardization Provided by IHS under license with ISO Licensee=Aramco HQ/9980755100 Not for Resale, 04/23/2007 09:27:08 MDTNo reproduction or networking permitted without license from IHS -,-,- Q IS0 , In accordance with IS0 525 and this part of IS0 603 4 Designatio
9、n A complete designation of a bonded abrasive product in accordance with this part of IS0 603 shall be consist of the following information: a) designation of the bonded abrasives, e.g. “Grinding wheel“; b) reference of this part of IS0 603; d) dimensions; e) specifications of an internal nature; f)
10、 the maximum operating speed. 1 EXAMPLE A grinding wheel for deburring, Type 1, D = 150 mm, T = 25 mm, H = 20 mm, nature of abrasive A, grain size 24, grade Q, structure 5, nature of bond B and a maximum operating speed of 50 m/s is designated as follows: Grinding wheel IS0 603-12 - 1 - 150 x 25 X 2
11、0 - A 24 Q5B - 50 m/s 5 Specifications The specifications are left to the manufactures discretion, see IS0 525. 5.1 Tolerances Limit deviations and run-out tolerances in accordance with IS0 13942. 5.2 Balancing Balancing is in accordance with IS0 61 03. 5.3 Marking Marking of bonded abrasive product
12、s is in accordance with IS0 525. 5 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Aramco HQ/9980755100 Not for Resale, 04/23/2007 09:27:08 MDTNo reproduction or networking permitted without license from IHS -,-,- Bibliography l IS0 8486-1, Bo
13、nded abrasives - Determination and designation of grain size distribution - Part 7: Macrogrits F4 to F220. 2 IS0 8486-2, Bonded abrasives - Determination and designation of grain size distribution - Part 2 : Microgrits F230 to f 1200. 6 Copyright International Organization for Standardization Provid
14、ed by IHS under license with ISO Licensee=Aramco HQ/9980755100 Not for Resale, 04/23/2007 09:27:08 MDTNo reproduction or networking permitted without license from IHS -,-,- STD-IS0 b03-12-ENGL 3999 4851903 0790335 OTO H IS0 603-1 2:1999( E) o IS0 ICs 25.1 00.70 Price based on 6 pages Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Aramco HQ/9980755100 Not for Resale, 04/23/2007 09:27:08 MDTNo reproduction or networking permitted without license from IHS -,-,-