《ISO-6618-1997.pdf》由会员分享，可在线阅读，更多相关《ISO-6618-1997.pdf（16页珍藏版）》请在三一文库上搜索。
1、INTERNATIONAL STANDARD IS0 6618 Second edition 1997-02-01 Petroleum products and lubricants - Determination of acid or base number - Colour-indicator titration method Produits p6 troliers et lubrifian ts - DGtermina tion de Iindice d acide ou de Iindice de base - M extremely weak acids or bases whos
2、e dissociation constants are less than IO-9 do not interfere. Salts react if their hydrolysis constants are greater than 10-g. NOTE 1 In new and used oils, the constituents considered to have acidic characteristics include organic and inorganic acids, esters, phenolic compounds, lactones, resins, sa
3、lts of heavy metals, and additives such as inhibitors and detergents. Similarly, constituents considered to have basic properties include organic and inorganic bases, amino compounds, salts of weak acids (soaps), basic salts of polyacidic bases, salts of heavy metals, and additives such as inhibitor
4、s and detergents. The method is not suitable for measuring the basic constituents of many basic additive-type lubricating oils, for which IS0 3771 can be used. This International Standard indicates relative changes that occur in an oil during use under oxidizing conditions. Although the titration is
5、 made under definite equilibrium conditions, the method does not measure an absolute acidic or basic property that can be used to predict performance of an oil under service conditions. NOTES 2 No general relationship between bearing corrosion and acid or base number is known. 3 Oils, such as many c
6、utting oils, rustproofing oils, and similar compounded oils, or excessively dark-coloured oils, that cannot be analysed by this method owing to obscurity of the colour-indicator end-point, can be analysed in accordance with IS0 6619. The acid or base numbers obtained by this colour-indicator method
7、may or may not be numerically the same as those obtained by IS0 6619, but they are generally of the same order of magnitude. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this International Standard. At the time of p
8、ublication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and IS0 maintain re
9、gisters of currently valid International Standards. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 02:49:21 MDTNo reproduction or networking permitted without license from IHS -
10、,-,- IS0 6618:1997(E) 0 IS0 IS0 3696: 1987, Water for analytical laboratory use - Specification and test methods. IS0 3771:1994, Petroleum products - Determination of base number - Perchloric acid po ten tiome tric titration method. IS0 6619:1988, Petroleum products and lubricants - Neutralization n
11、umber - Po ten tiome tric titration method. NOTES 1 IS0 3771 employs the use of chlorobenzene as a solvent. Alternatives to this solvent are being sought. 2 IS0 6619 is under review, and the scope will be restricted to acid number. 3 Definitions For the purposes of this International Standard, the f
12、ollowing definitions apply. 3.1 acid number: Quantity of base, expressed in milligrams of potassium hydroxide (KOH) per gram of sample, that is required to titrate the acid constituents present in 1 g of sample when titrated under prescribed conditions. 3.2 strong acid number: Quantity of basel expr
13、essed in milligrams of potassium hydroxide (KOH) per gram of sample, that is required to titrate the strong acid constituents present in 1 g of sample when titrated under - prescribed conditions. 3.3 base number: Quantity of acid, expressed in terms of the equivalent number of milligrams of potassiu
14、m hydroxide (KOH) per gram of sample, that is required to titrate the base constituents present in 1 g of sample when titrated under prescribed conditions. 4 Principle To determine the acid number or base number, the test portion is dissolved in a mixture of toluene and propan-Z-01 containing a smal
15、l amount of water, and the resulting single-phase solution is titrated at room temperature with standard alcoholic base or alcoholic acid solution, respectively, to the end-point indicated by the colour change of added pnaphtholbenzein solution (orange in acid and green-brown in base). To determine
16、the strong acid number, a separate portion of the sample is extracted with boiling water and the aqueous extract is titrated with potassium hydroxide solution using methyl orange as indicator. 5 Reagents and materials During the analysis, use only reagents of recognized analytical grade, and only wa
17、ter in accordance with Grade 3 of IS0 3696. 5.1 Propan-Z-01, anhydrous, maximum water content 0,9 %(V/v) (volume fraction 0,9 %). 5.2 Toluene. 5.3 Titration solvent. Add 500 ml of toluene (5.2) and 5 ml of water to 495 ml of propan-2-01 (5.1). 5.4 Hydrochloric acid, c(HCI) = 0,l mol/l standard volum
18、etric alcoholic solution. Prepare in accordance with 5.4.1 or use commercially available solution. Standardize in accordance with 5.4.2. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/2
19、1/2007 02:49:21 MDTNo reproduction or networking permitted without license from IHS -,-,- 0 IS0 IS0 6618:1997(E) 5.4.1 Preparation Mix 9 ml of concentrated HCI 35,4 %( avoid unnecessary exposure to carb on d ioxide during filtration. Store the solution in a chemically resistant dispensing bottle out
20、 of contact with cork, rubber or saponifiable stopcock lubricant and protected by a guard tube containing soda lime or nonfibrous soda silicate absorbentl). Glass bottles are not recommended for storage. 5.52 Standardization Standardize frequently enough to detect changes of 0,000 5 mol/l, preferabl
21、y against 0,l g to 0,15 g of pure potassium acid phthalate (5.9) weighed with an accuracy of 0,000 2 g and dissolved in approximately 100 ml of carbon dioxide-free water, using phenolphthalein (5.8) to detect the end-point. NOTES 1 To simplify calculations, both the standard potassium hydroxide and
22、hydrochloric acid solutions may be adjusted so that 1 ml is equivalent to 5 mg of KOH. 2 Because of the relatively large coefficient of cubic expansion of organic liquids such as propan-2-01, the standard alcoholic solutions should be standardized at temperatures close to those employed in the titra
23、tions of sample, and close to 20 “C. 56 . Methyl orange, indicator solution. Dissolve 0,l g of methyl orange in 100 ml of water. 5.7 p-naphtholbenzein indicator solution, meeting the specifications given in annexes A and B. Dissolve I,0 g of pnaphtholbenzein in 100 ml of titration solvent (5.3). NOT
24、E- In a study in 1992, only one co mmercially available sou Careful adhe rence to this requirem ent is t herefore recommended. rce of this indicator met the s pecif ica tion given in annex A*). 1) Ascarite, Carbosorb and lnde carb are examples of suitable products available commercially. T the conve
25、nie nce of users of this I nternational Standa rd and does not cons titute an endorsement by his I IS0 nformation is given of these products. for 2) Solid knaphtholbenzein meeting the specification given in annex A is available from Distillation Products Industries, Eastman Organic Chemicals Dept.,
26、Rochester 3, New York, USA. This information is given for the convenience of users of this International Standard and does not constitute an endorsement by IS0 of the product named. Equivalent products may be used if they can be shown to lead to the same results. Copyright International Organization
27、 for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 02:49:21 MDTNo reproduction or networking permitted without license from IHS -,-,- IS0 6618:1997(E) 5.8 Phenolphthalein, indicator solution. Dissolve 0,5 g of phenolp
28、hthalein in 100 ml propan-2-01 (5.1). 5.9 Potassium acid phthalate. 6 Apparatus Ordinary laboratory apparatus and: 6.1 Burette, capacity 50 ml, graduated in 0,l ml subdivisions, or capacity 10 ml, graduated in 0,05 ml subdivisions. 7 Preparation of used oil sample 7.1 Strictly observe the sampling p
29、rocedure in 7.2 and 7.3. Failure to obtain a representative test portion causes serious errors. NOTE - Sediment may be acidic or basic, or may have absorbed acidic or basic material from the sample. As used oil may change appreciably in storage, samples should be tested as soon as possible after rem
30、oval from the lubricating system; the dates of sampling and testing should be noted. 7.2 Heat the laboratory sample of used oil to 60 “C IfI 5 “C in the original container and agitate until all of the sediment is homogeneously suspended in the oil. If the original container is a can, or if it is gla
31、ss and more than three-quarters full, transfer the entire sample to a clear glass bottle having a capacity at least one-third greater than the volume of the sample. Transfer all traces of sediment from the original container to the bottle by violent agitation of portions of the sample in the origina
32、l container. NOTE - When laboratory samples are visibly free from sediment the heating procedure described may be omitted 7.3 After complete suspension of all sediment, filter the test sample, or a convenient aliquot, through a 150 pm wire mesh filter to remove large contaminating particles. 8 Deter
33、mination of acid number 8.1 Into a 250-ml conical flask, introduce the appropriate mass of test portion given in table 1. Add 100 ml of the titration solvent (5.3) and 0,5 ml of the indicator solution (5.7) and, without stoppering, swirl until the test portion is completely dissolved by the solvent.
34、 If the mixture assumes a yellow-orange colour, proceed as specified in 8.2; if it becomes green or green-black, proceed as specified in clause 9. Table 1 - Mass of test portion Type of oil Acid or base number Mass of test portion Accuracy of weighing cl g I New or light-coloured 63 20 + 2 0,05 3 to
35、 25 2 rf: 0,2 0,Ol 25 to 250 0,2 + 0,02 0,001 Used or dark-coloured =s 25 2 Ifr 0,2 0,Ol 25 to 250 I I I 0,2 + 0,02 I 0,001 I NOTE - Light-coloured test portions of low acid number permit the use of 20-g test portions to obtain more precise results. The test portion size for dark-coloured oils is li
36、mited to the quantity specified to minimize possible interference by the dark colour. 4 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007 02:49:21 MDTNo reproduction or networking
37、permitted without license from IHS -,-,- 0 IS0 IS0 6618:1997(E) 8.2 Titrate immediately at a temperature below 30 “C. Add the potassium hydroxide solution (5.5) in increments and swirl to disperse the potassium hydroxide as necessary. Shake vigorously near the end-point but avoid dissolving carbon d
38、ioxide in the solvent. Consider the end-point definite if the colour change persists for 15 s or if it reverses on addition of two drops of the hydrochloric acid solution (5.4). In the case of acidic oils, the orange colour changes to a green or green-brown as the end-point is approached. To observe
39、 the end-point of dark-coloured oil, shake the flask vigorously to produce momentarily a slight foam when the colour change occurs as the last few drops of titrant are added and observe the titration under a white fluorescent lamp at bench-top level. 8.3 Carry out a blank titration on 100 ml of the
40、titration solvent and 0,5 ml of the indicator solution, adding the potassium hydroxide in 0,05 ml or 0,l ml increments. Record the quantity of potassium hydroxide solution required to reach the end-point (orange to green). 9 Determination of base number 9.1 If the titration solvent (5.3) containing
41、the dissolved test portion assumes a green or greenish-brown colour after the indicator is added (8.1) carry out the titration as specified in 8.2, but use the hydrochloric acid (5.4) as titrant and titrate until the green-brown colour changes to orange. 9.2 Carry out a blank titration as specified
42、in 8.3. NOTE - The titration solvent usually contains weak acid impurities which react with the strongly basic components of the test portion. To correct the base number for the test portion, it is thus necessary to determine an acid number blank of the solvent. 10 Determination of strong acid numbe
43、r 10.1 Introduce approximately 25 g of a representative sample, weighed to within O,O5 g, into a ZSO-ml separating funnel, and add 100 ml of boiling water. Shake vigorously and, after phase separation, collect the aqueous phase in a 500-ml beaker. Make two new extractions from the test sample, each
44、time with 50 ml of boiling water, and add the extracts obtained to the same beaker. To the combined extracts add 0,l ml of the methyl orange indicator (5.6) and, if the solution becomes pink or red, titrate with the potassium hydroxide solution (5.5) until the solution becomes golden-brown in colour
45、. If the initial colour is not pink or red, report the strong acid number as zero. IO.2 Into a 250-ml conical flask, introduce 200 ml of the boiling water from the same source. Add 0,l ml of the methyl orange indicator solution (5.6). If the indicator solution is yellow-orange, titrate with the hydr
46、ochloric acid solution (5.4) to the same depth and shade of colour obtained in the titration of the test portion. If the indicator colour is pink or red, titrate with the potassium hydroxide solution (5.5) to the same end-point as that used in the test portion titration. 11 Calculation 11.1 Acid num
47、ber Calculate the acid number, AN, in milligrams of KOH per gram of the test sample, from the equation: AN= (VI - Vo)cKoH x 5671 m Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/21/2007
48、 02:49:21 MDTNo reproduction or networking permitted without license from IHS -,-,- IS0 6618:1997(E) IS0 where VI is the volume, in millilitres, of potassium hydroxide solution required for titration of the test portion; VO is the volume, in millilitres, of potassium hydroxide solution required for
49、titration of the blank solution; CKOH is the concentration, in moles per litre, of the standard volumetric potassium hydroxide solution; m is the mass, in grams , of the test portion. 11.2 Strong acid number Calculate the strong acid number, SAN, in milligrams of KOH per gram of test sample, from either equation (Z), if the blank titration is made with acid, or equatio