《ISO-15750-1-2002.pdf》由会员分享，可在线阅读，更多相关《ISO-15750-1-2002.pdf（12页珍藏版）》请在三一文库上搜索。
1、Reference number ISO 15750-1:2002(E) ISO 2002 INTERNATIONAL STANDARD ISO 15750-1 First edition 2002-04-15 Packaging Steel drums Part 1: Removable head (open head) drums with a minimum total capacity of 208 l, 210 l and 216,5 l Emballages Fts en acier Partie 1: Fts ouverture totale dune capacit total
2、e minimale de 208 l, 210 l et 216,5 l ISO 15750-1:2002(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the c
3、omputer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to c
4、reate this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform
5、the Central Secretariat at the address given below. ISO 2002 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from eith
6、er ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.ch Web www.iso.ch Printed in Switzerland ii ISO 2002 All rights reserved -,-,- ISO 15750-1:2002(E)
7、ISO 2002 All rights reservediii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body inter
8、ested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
9、 Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the te
10、chnical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this part of ISO 15750 may be the subject of patent r
11、ights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 15750-1 was prepared by Technical Committee ISO/TC 122, Packaging. ISO 15750 consists of the following parts, under the general title Packaging Steel drums: Part 1: Removable head (open head) drums with a min
12、imum total capacity of 208 l, 210 l and 216,5 l Part 2: Non-removable head (tight head) drums with a minimum total capacity of 212 l, 216,5 l and 230 l Part 3: Inserted flange-type closure systems Annex A forms a normative part of this part of ISO 15750. ISO 15750-1:2002(E) iv ISO 2002 All rights re
13、served Introduction Throughout the world a large number of steel drum types with different dimensions and characteristics are being used. The differences in location of the filling opening and outer dimensions result in differences in filling, handling and transportation. This part of ISO 15750 give
14、s uniform specifications for four main types of drums for use in international trade and the preferred target option is drum type A (see Table 1). It specifies the characteristics and dimensions of steel drums which are of importance for the exchangeability, and does not give detailed performance re
15、quirements and related test methods. The performance requirements depend on the specific application. Where the drums are intended to be used for the transport of dangerous goods, attention is drawn to the regulatory requirements which govern the transport of those goods in the countries concerned,
16、including capseals/overseals fitted in accordance with the certificate. Depending upon the mode of transport, this means meeting the requirements of: UN (United Nations): Recommendations on the transport of dangerous goods. Model regulations; ICAO (International Civil Aviation Organization): Technic
17、al Instructions for safe transport of dangerous goods by air; IMO (International Maritime Organization): International Maritime Dangerous Goods (IMDG) Code. This involves the certification and marking of the drums according to the regulations. -,-,- INTERNATIONAL STANDARDISO 15750-1:2002(E) ISO 2002
18、 All rights reserved1 Packaging Steel drums Part 1: Removable head (open head) drums with a minimum total capacity of 208 l, 210 l and 216,5 l 1Scope This part of ISO 15750 specifies the characteristics and dimensions of removable head (open head) drums, manufactured from steel sheet, having a total
19、 capacity of 208 l, 210 l and 216,5 l. It also specifies a method for measuring the total and brimful capacity. 2Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this part of ISO 15750. For dated references, sub
20、sequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this part of ISO 15750 are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the la
21、test edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 228-1:2000, Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation ISO 3573:1986, Hot-rol
22、led carbon steel sheet of commercial and drawing qualities ISO 3574:1986, Cold-reduced carbon steel sheet of commercial and drawing qualities ISO 15750-3, Packaging Steel drums Part 3: Inserted flange-type closure systems 3Terms and definitions For the purposes of this part of ISO 15750, the followi
23、ng terms and definitions apply. 3.1 removable head (open head) drum OH cylindrical packaging made of steel, the bottom end of which is permanently fixed to the body and the top end can be removed as a lid and closed by means of a closing ring NOTEThe top end may have additional openings for filling
24、and venting. 3.2 round seam seam consisting of six or more layers of steel -,-,- ISO 15750-1:2002(E) 2 ISO 2002 All rights reserved 3.3 nominal capacity capacity, in litres, which by convention is used to represent a class of drums of similar brimful capacities 3.4 brimful capacity volume of water,
25、in litres, held by the drum when filled through the fitted filling orifice to the point of overflowing, the drum being closed and having a lid fitted with closures NOTEAnnex A specifies the measuring method. 3.5 total capacity TC volume of water, in litres, held by the drum when filled completely, i
26、.e. following the removal of any air trapped in the drum, the drum being closed and having a lid fitted with closures NOTEAnnex A specifies the measuring method. 4Dimensions The dimensions of the drum shall be as shown in Figure 1 and detailed in Table 1 for drum type A, B, C or D. The steel thickne
27、ss shall be between 0,6 mm and 1,6 mm, with tolerances according to ISO 3573 or ISO 3574 (normal tolerances). 5Material Body and ends shall be of steel sheet CR1 (commercial quality) for cold-reduced steel, according to ISO 3574:1986, or of steel sheet HR1 (commercial quality) for hot-rolled steel a
28、ccording to ISO 3573:1986. Steel of higher strength is permitted. Closure flanges shall be manufactured from metal, and closure plugs from metal or plastics material. 6Construction 6.1Body and heads shall be constructed of steel of adequate thickness in relation to the intended use. 6.2The longitudi
29、nal seam of the body shall be welded. 6.3The body and bottom end shall be permanently fixed by round seaming as shown in Figure 1, detail A, using a non-hardening seaming compound, or other joining methods (e.g. welding). 6.4Two rolling hoops (beads) expanded or rolled into the body shall be located
30、 as shown in Figure 1. Constructions of rolling hoops other than those shown are allowed including a third rolling hoop (bead), or replacement of the beads by small corrugations. NOTEThe preferred drum type is the drum with two rolling hoops only. 6.5The removable top end shall be fitted with a gask
31、et of suitable material. 6.6The construction of the closing ring shall be such that the tightness of the drum is not jeopardized. -,-,- ISO 15750-1:2002(E) ISO 2002 All rights reserved3 Dimensions in millimetres a Closures (optional). b Third bead is optional. c Detail of drum type B + D. Figure 1 R
32、emovable head (open head) drum -,-,- ISO 15750-1:2002(E) 4 ISO 2002 All rights reserved Table 1 Dimensions of removable head (open head) steel drums Dimensions in millimetres Description Drum Type A Drum Type B Drum Type C Drum Type D Dimension (see Figure 1) Total capacity 210 l min. 216,5 l min. 2
33、10 l min. 216,5 l min. 208 l min. 208 l min. D1Internal diameter 571,5 2571,5 2571,5 2571,5 2566 2566 2 D2External diameter over rolling hoops 585 max.585 max.596 max.596 max.585 max.585 max. D3Diameter over bottom chime 585 max.585 max.593 max.593 max.585 max.585 max. D4Diameter over closing ring 5
34、85 maxa585 max.a610 max.610 max.585 max.a620 max. H1Total drum height 878 5888 5878 5888 5890 5890 5 H5Height with cover off 868 5878 5868 5878 5880 5880 5 h2Depth of topbbbbbb h3Clearance from floor 4 min.4 min.4 min.4 min.4 min.4 min. h4Distance between beads 280 3280 3280 3280 3300 3300 3 p1Centr
35、e-to-centre distance of closurescccccc p2Location of G2 (50 mm) closure to outside body, measured approximately 50 mm from the top 72 372 372 372 394 394 3 The total capacity shall be as indicated when measured in accordance with annex A. Closures are optional. If closures are fitted, the insertion
36、of the closure with the G2 thread according to ISO 15750-3 shall be such that its centreline is as close as possible to the vertical. NOTE 1Of the four drum types shown, types A and C have the optimal outside dimensions required for stacking drums four abreast in ISO containers as per ISO 668:1995,
37、Series 1 freight containers Classification, dimensions and ratings. NOTE 2For types A and C, the diameter D4is achieved by modification of the top construction. The two approaches in use are as follows. a)Reduction of the drum whereby the closing system (curl, cover, closing ring) maintains the same
38、 dimensions as in use for type B and type D. The required inside diameter of the reduced top part of the drum is in this case approx. 545 mm for type A and 536 mm for type C. b)Changing of the closing system (curl, cover and closing ring) so that, while maintaining the inside diameter at 571,5 mm fo
39、r type A and 566 mm for type C, the total outside diameter is kept within 585 mm. a The diameter over the closing ring shall normally be a maximum of 585 mm but may be slightly larger if measured over the lever section or bolt section of the ring. b If the lid is fitted with closures, the depth of t
40、he top shall be such that the closures do not protrude above the closing ring. c For the centre to centre distance of the closures the dimensions shall be: drum type A and B: 444 mm 6 mm or 451 mm 1 mm; drum type C and D: 400 mm 6 mm. -,-,- ISO 15750-1:2002(E) ISO 2002 All rights reserved5 6.7If add
41、itional closures are provided in the top end, the following applies. a)The closures shall be positioned in the top end, diametrically opposed as indicated in Figure 1. b)The nominal pitch diameter and pitch of the closures shall be as defined in ISO 228-1, threads G 3/4 and G 2. c)The closures shoul
42、d be as specified in ISO 15750-3, unless otherwise agreed between the purchaser and manufacturer. d)Gaskets/washers or other sealing elements shall be used with the closures unless the fittings are inherently leakproof. e)The metal or plastics plugs shall be fitted with washers/gaskets of suitable m
43、aterial. 7Finish 7.1The nature of the internal and external finish shall be agreed between the purchaser and manufacturer. 7.2If materials used for the body, heads and fittings are not in themselves compatible with the contents to be transported, suitable internal protective coatings or treatments s
44、hall be applied. These coatings or treatments shall retain their protective properties under normal conditions of transport. 8Designation A removable head (open head) drum manufactured to this part of ISO 15750 shall be designated as follows: Open head steel drum ISO 15750-1-(total capacity)TC-Type
45、EXAMPLES Open head steel drum ISO 15750-1-216,5TC-A Open head steel drum ISO 15750-1-208TC-D Open head steel drum ISO 15750-1-208TC-C Open head steel drum ISO 15750-1-210TC-B ISO 15750-1:2002(E) 6 ISO 2002 All rights reserved Annex A (normative) Capacity measurement method for removable head (open h
46、ead) drums A.1 Principle The capacity is determined by a gravimetric method; i.e. by measurement of the mass of water in the packaging and its conversion to a capacity. A correction factor may be applied according to Table A.1, but only if the weighing scale used is of a higher precision than the co
47、rrection. For both methods at least a G 2 closure shall be fitted in the lid and this is the closure referred to in the procedures. Table A.1 Temperature-dependent correction factor Water temperature C Correction factor F 121,000 5 141,000 8 161,001 1 181,001 4 201,001 8 221,002 2 241,002 7 261,003
48、3 281,003 8 301,004 4 A.2 Apparatus The accuracy of the weighing scale shall be at least 0,1 % of the mass being measured. A.3 Procedure A.3.1 Determination of the total capacity Drill a hole of diameter 5 mm to 10 mm for venting at the highest point of the closed drum. The position of the hole depends on the profile of the top. Weigh the empty drum and record its mass, m1, in grams. Use tap water and measure its temperature. Fill the drum with water through the G 2 filling closur