《ISO-24410-2005.pdf》由会员分享，可在线阅读，更多相关《ISO-24410-2005.pdf（10页珍藏版）》请在三一文库上搜索。
1、 Reference number ISO 24410:2005(E) ISO 2005 INTERNATIONAL STANDARD ISO 24410 First edition 2005-04-15 Earth-moving machinery Coupling of attachments to skid steer loaders Engins de terrassement Attelage des accessoires des chargeuses direction articule ISO 24410:2005(E) PDF disclaimer This PDF file
2、 may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the r
3、esponsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-cre
4、ation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2005 All rights reserved. Unle
5、ss otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO c
6、opyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2005 All rights reserved ISO 24410:2005(E) ISO 2005 All rights reserved iii Foreword ISO (the International Organization for Standard
7、ization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to
8、be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Stand
9、ards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an Inte
10、rnational Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 24410
11、was prepared by Technical Committee ISO/TC 127, Earth-moving machinery, Subcommittee SC 2, Safety requirements and human factors. INTERNATIONAL STANDARD ISO 24410:2005(E) ISO 2005 All rights reserved 1 Earth-moving machinery Coupling of attachments to skid steer loaders 1 Scope This International St
12、andard provides for the interchangeability of attachments on skid steer loaders by establishing dimensional limits for the attachment interface. It is applicable to skid steer loaders whose operating mass according to ISO 6165 is 4 500 kg or less. Narrow skid steer loaders may have a width that does
13、 not allow compliance. Its requirements do not restrict the design of the attachment bracket locking system, which is left to the discretion of the manufacturer. It is not applicable to attachment interface brackets connected to the attachment bracket by a lateral locking system. 2 Normative referen
14、ces The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 6165, Earth-moving machinery Basic types
15、Vocabulary ISO 6746-2, Earth-moving machinery Definitions of dimensions and codes Part 2: Equipment and attachments 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 6165 and ISO 6746-2 and the following apply. 3.1 attachment interface attachment compo
16、nent that facilitates the quick mounting and removal of an attachment to the attachment bracket 3.2 attachment bracket skid steer loader component that facilitates quick interchange of attachments 4 Mounting dimensions The mounting dimensions for the attachment interface shall be as shown in Figures
17、 1 to 4. The attachment shall only have components outside the described space. ISO 24410:2005(E) 2 ISO 2005 All rights reserved The attachment bracket shall not protrude above surface A, forward of surface B, or below surface C See Figure 4. NOTE Some attachments could require added support structu
18、re to the attachment interface between surfaces A and B. Key F forward direction Figure 1 Attachment interface Isometric view ISO 24410:2005(E) ISO 2005 All rights reserved 3 Dimensions in millimetres Figure 2 Attachment interface Rear view Dimensions in millimetres Figure 3 Attachment interface Sec
19、tion AA (Figure 2) ISO 24410:2005(E) 4 ISO 2005 All rights reserved Dimensions in millimetres Figure 4 Attachment interface Section XX (Figure 2) -,-,- ISO 24410:2005(E) ISO 2005 All rights reserved 5 Bibliography 1 ISO 7131:1997, Earth-moving machinery Loaders Terminology and commercial specifications -,-,- ISO 24410:2005(E) ICS 53.100 Price based on 5 pages ISO 2005 All rights reserved