《JIS-A-4714-1985-ENG.pdf》由会员分享，可在线阅读，更多相关《JIS-A-4714-1985-ENG.pdf（27页珍藏版）》请在三一文库上搜索。
1、 J I S A84714 85 M 4933608 000Lbb9 L M J UDC 692.82 : 691.175 : 678.743 IS JAPANESE INDUSTRIAL STANDARD. PVC Windows for Int-erior Installed Translated and Published bY Japanese Standards Association Printed in Japan 14 S Copyright Japanese Standards Association Provided by IHS under license with JS
2、ALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/14/2007 08:41:41 MDTNo reproduction or networking permitted without license from IHS -,-,- J I S A84714 85 m 4933b08 0001b70 13 m In the event of any doubt arising, the original Standard in Japanese is to be final authority. I
3、Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/14/2007 08:41:41 MDTNo reproduction or networking permitted without license from IHS -,-,- UDC 692.8269 1.175:678.743 JAPANESE INDUSTRIAL STANDARD J
4、I S PVC Windows for Interior Installed A 4714-1985 1. Scope This Japanese industrial Standard specifies PVC windows (l) for interior installed used for multiple windows at an opening in the outer wall of a building, hereinafter referred to as the “windows for interior installed“. Note (I) The PVC wi
5、ndows for interior installed shall be the windows for interior installed in the multiple windows using a glass, except for those for exterior installed. Their main components shall be of extruded materials according to JIS K 6740, and steel and aluminium alloy materials shall be used together as rei
6、nforcement, as required. Remark: The units and numerical values given in in accordance with the International System of Units, and are in this Standard are appended for informative reference. 2. Types and Symbols The symbol indicating windows for interior installed shall be itpit, and the windows sh
7、all be classified as shown in following (i) to (3). (1) The classification by the method of opening and closing shall be as shown . in Table 1. Table 1 Classification by method of Symbol opening/closing Remark A window movable in a plane in I the horizontal or vertical direction IH Sliding - Swing R
8、 A window which swings Remark: A fixed sash window shall be multistage window with a swing window and be “sliding“ when used in a multistage window with a sliding window. In the case of a fixed sash window alone, it shall be classified into %lidingt1. when used in a (2) The classification by the typ
9、e of sheet glass shall be as shown in Table 2. Applicable Standards: See pages 22, 23 and 24. Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/14/2007 08:41:41 MDTNo reproduction or networking permi
10、tted without license from IHS -,-,- I J I S A*47I4 85 W 4933b08 000Lb72 I 2 A 4714-1985 Table 2 I Symbol I Classification by type of sheet glass Remark With single glass MO Float glass, patterned glass, wire- net glass, wired glass, laminated glass, toughened glass, and so on I I Double glazing usin
11、g above- I I mentioned glasses With double glazing (3) The classification by performance shall be as shown in Table 3 (refer to Table 8). Table 3 Classification by performance Ordinary window for interior installed Airtight window for interior installed 3. Construction Symbol U t Remark That of a gr
12、ade not less than 40 kgf/m2 C392.3 N/m2) in wind- pressure resistance having an air tightness corresponding to grade 30 That of a grade not less than 60 kgf/m2 C588.4 N/m2) in wind- pressure resistance having an air tightness corresponding to grade 8 or grade 2 3.1 Shape of Frame for Windows for Int
13、erior Installed The shape of frame for windows for interior installed shall be suitable for fitting to the skeleton of a building, the interior structure or the frame of an exterior window. The sill used for a doorway shall not be deformed or damaged easily in the ordinary use. 3.2 Assembling The jo
14、ints in the assembly of main component members of windows for interior installed shall be made by fusion welding of resin, adhesion, fixing by bolts using an auxiliary metal member, fixing by screws, or others, such that they do not be easily separated by an external force. 3.3 Fixing of Attached Co
15、mponents The fixing portions of attached components used for windows for interior installed shall have a sufficient strength, for example, by the use of an auxiliary metal member. shall be so constructed that they are exchangeable. The attached components Copyright Japanese Standards Association Pro
16、vided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/14/2007 08:41:41 MDTNo reproduction or networking permitted without license from IHS -,-,- J I S A*4714 5 m 4733608 O003673 3 m 3 A 4714-1985 3.4 Reinforcement When a steel product is used as a
17、 reinforcement of windows for interior installed, the thickness shall be 1.2 mm and over, and the minimum zinc deposite mass by hot dip galvanizing, be 90 g/m2 and over. When metal materials are to be used, measures shall be taken to prevent occurence of contact corrosion between different metals. 3
18、.5 Recess for Thermal Expansion of PVC The windows for interior installed shall have a construction wherein the deformation of principal component members due to the thermal expansion can be absorbed. 3.6 Connection of Groove for Glass and Glass The shape of groove for glass of a window for interior
19、 installed and the connection of the groove for glass and the glass to be used shall be as shown in the following (1) to (3). (1) The designation of dimensions of connection between the groove for glass and the glass shall be as shown in Fig. 1. Fig. 1 a : Surface clearance I : Edge clearance c : Co
20、nnection dimension (2) In placing a wire-net glass, a wired glass and a double glazing, the edge clearance b at the lower side shall be 7 mm and over, and a channel-shaped gasket shall not be used. (3) In placing a double glazing, the connection dimension c shall be 12 mm and over. Remark: When usin
21、g a float glass, a patterned glass and a toughened glass, 6.1 of JIS A 4706 shall be followed. 3.7 Removal of Water in Contact with Wire-Net Glass, Wired Glass, Laminated Glass and Double Glazing The windows using a wire-net glass, a wired glass, a laminated glass and a double glazing shall be const
22、ructed such that the water in contact with the edge portion of the glass can rapidly be removed. The dimension of a drain hole shall be 5 mm and over in diameter in the case of a round hole, 3 mm and over in width in the case of a slit and 18 mm2 and over in area with a minor diameter of 4 mm and ov
23、er in the case. of an elliptic hole. The number of drain holes in the bottom rail and the sill shall be 3 and more disposed at the center, right and left portions between the setting blocks of the glass. However, when the setting blocks do not serve as a dam, the drain hole at the center may be omit
24、ted. 4. Dimensions 4.1 Width and Height of Windows for Interior Installed The restriction for the width and height of windows for interior installed shall be defined as shown in Figs. 2.1 to 2.3. Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/11
25、11111001, User=Wing, Bernie Not for Resale, 03/14/2007 08:41:41 MDTNo reproduction or networking permitted without license from IHS -,-,- I J I S A84714 85 4733608 0001674 5 W 4 A 4714-1985 4.2 Nominal Dimensions for Width and Height of Windows for Interior Installed interior installed shall be in a
26、ccordance with the module nominal dimensions of the doors and windows specified in JIS A 4702 and JIS A 4706, and the nominal dimensions for the width (w) and height (H) shall be as given in Tables 4.1 to 4.4. The module nominal dimensions for width v W and height v H of windows for Nomin.al dimensj
27、on for width of windows for interior installed W nini Nominal dimensions djmen- sions windows height of windows for Nomi- interior na1 installed dimen- sions for windows 500 I 600 j-+ 1100 1200 2 400 2m 2 500 - 350 4.00 - 3303 3305 - 550 600 - 0503 0505 0507 0509 - - Table 4.1 1950 2350 3150 Il 2000
28、 2400 3200 1903 2303 3103 1905 2305 3105 1907 2307 3107 1909 2309 3109 1919 2319 3119 1920 2320 3120 1921 2321 3121 1923 2323 3123 1924 2324 3124 1926 2326 3126 1929 2329 3129 1931 2331 3131 Remark: The table applies to the openings specified in JIS A 0005. 3 950 - 4000 - 3903 3905 3907 - 3909 3911
29、3915 3919 - - 3920 392 1 3923 3924 3926 3929 - - 3931 - Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/14/2007 08:41:41 MDTNo reproduction or networking permitted without license from IHS -,-,- J
30、I S A94714 85 L1933608 0001b75 7 W 1600 1600 1604 1605 i605(1)* 1607 1610 1612 1613 1614 1616 1619 1619(1)* 1620 1621 1740 1700 1704 1705 1705(11 1707 1710 1712 1713 1714 1716 1719 1719(1) 1720 1721 5 A 4714-1985 Table 4.2 - 1 270 - 1 400 - 1 800 - 1920 - 2 100 2 100 Nornin,al dimenS.ion for width o
31、f windows for interior installed w nim 870 1500 1 500 - 1504 1505 1900 - 1904 900 1800 - 1804 1 300 - 1204 1205 1400 1404 1405 2104 0804 0805 1805 1805(1 1807 1810 - - 1905 2105 0805( i)* 1205(1) 1405(1) 1407 1505(1: 1507 1905(1) 1907 2105( l)* 2107 2110 2112 1207 1210 0807 0810 1510 1910 1 080 1050
32、 1410 1412 0812 1212 1512 1812 1813 1814 - - 1912 0813 1213 1413 2113 2114 1513 1514 1516 1913 1914 1214 - 1414 1416 - 1816 1916 2116 1819 1919 2119 1819(1 1919(1) 21 19( i)* 1820 1821 - - 1920 1921 - 2120 2121 Note *: Remark: (1) denotes a symbol indicating that the nominal dimension for height (if
33、) of the window for interior installed is different. The table applies to the openings of reinforced concrete constructions and steel frame buildings. Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 0
34、3/14/2007 08:41:41 MDTNo reproduction or networking permitted without license from IHS -,-,- I , I J I S A*4734 85 E 4733608 0003676 9 I 6 A 4714-1985 Table 4.3 Nominal dimension for width of windows for interior installed W mm 810 870 1 741 - 1 70 7 1703 1 9 2 8 - 190 - 1903 2 63 - 2 61 - 2603 2 88
35、C - 2 855 - 2803 1270 140 1245 137( 1203 1403 1204 1404 1206 1406 1207 1407 1208 1408 1209 1409 1210 1410 1211 1411 1212 1412 3 840 - 3 aio Nominal dimensions for width of exterior windows Nomi- dimen- sions for height of exterior windows I H m m Nominal djmen- for height o f windows fqr interior in
36、stalled H mm s10ns 790 - D803 840 370 365 0803(4)* * 460 455 3804 0804(i)* * 1704 1904 2604 2804 630 605 1806 0806(4)* 1706 1707 1708 - - 1906 2606 2806 755 3807 3808 - 1907 1908 _ 2807 2808 - O807(4)* * D808(4)* 2607 2608 2609 780 855 I 3508 3808 850 930 910 1709 1909 2809 1 060 1710 1711 - 1910 19
37、11 - 2610 261 1 2810 2811 1 080 1190 1215 1210 1712 1912 2612 2812 1713 - i717 1913 1917 - 2613 2617 2813 2817 1365 1760 1380 1780 1 820 1 790 i718 1918 2618 2818 1518 I3818 1900 1850 1719 1919 2619 2819 1519 I 3819 2 100 L721 .722 - 1921 i922 - 1621 1622 - 2 100 2 240 2821 2822 2823 2 200 2 320 2 3
38、00 .723 1923 1623 Note *: Remark: II (4) II denotes a symbol indicating that the nominal dimension for width ( w ) of the window for interior installed is different. The table applies to the openings of wooden buildings. Copyright Japanese Standards Association Provided by IHS under license with JSA
39、Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/14/2007 08:41:41 MDTNo reproduction or networking permitted without license from IHS -,-,- . J I S AM4734 85 = 4933608 0003677 O 7 A 4714-1985 Table 4.4 - 430 600 730 870 510 920 V w riin 430 - 0404 - 510 590 730 890 920 Nomi- d
40、imen- sions for height of exterior windows H min VHrnin 460 500 430 500 0805 0505 0605 0705 560 560 0505(1)* 0605(1)* I 0705 OSOS( i)* 0905( i)* 0507 + 780 855 750 850 0807 0808 0707 0708 0907 0908 930 910 0709 0809 0909 960 960 0709( 1)* 0809(1)* 0909(1)* 0913 1380 1360 0713 0813 1780 1 750 0817 09
41、17 0818 0918 1 820 1 900 1 820 1900 0819 0821 0919 0921 2 100 2 100 2 240 2 240 0822 0922 2 320 2 300 0823 0923 Remark: The table applies to the swing windows for interior installed. Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, Use
42、r=Wing, Bernie Not for Resale, 03/14/2007 08:41:41 MDTNo reproduction or networking permitted without license from IHS -,-,- I- J I S A*4734 85 = 4933608 0003678 2 = 8 A 4714-1985 Fig. 2.1. Examples of Restrictions of Module Nominal Dimensions and Product Dimensions r - . . Il ” - - I c / I. I, Copy
43、right Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/14/2007 08:41:41 MDTNo reproduction or networking permitted without license from IHS -,-,- J I S A84714 85 4933608 0003679 4 9 A 4714-1985 Fig. 2.2. Exam
44、ples of Restrictions of Module Nominal Dimensions and Product Dimensions Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/14/2007 08:41:41 MDTNo reproduction or networking permitted without license
45、from IHS -,-,- J I S As4714 85 W 4933hU8 CiUEb813 O W 10 A 4714-1985 Fig. 2.3. Examples of Restrictions of Module Nominal Dimensions and Product Dimensions f u Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for
46、Resale, 03/14/2007 08:41:41 MDTNo reproduction or networking permitted without license from IHS -,-,- 11 A 4714-1985 windows interior exterior windows installed 4.3 The module nominal dimension of windows for interior depth of frame v T shall be as given in Table 5. Table 5 Unit: mm Nominal dimen- s
47、ions and module Type of buildng nominal dimen- Range of sions of product windows for dimensions construction interior installed Remark: The values in ( ) shall be the preferred dimensions. Sliding and swing 4.4 Product Dimensions of Windows for Interior Installed The product dimensions of windows fo
48、r interior installed shall be such that the width (zu) and Reinforced concrete .building, steel Table 4.1 frame building and wooden building O O W- 10 -10 height (k) are in the range given in Table 6 for the nominal dimensions ( W ) and ( H ) , respectively, and the depth of frame is in the range given in Table 6