《ISO-9080-2003.pdf》由会员分享，可在线阅读，更多相关《ISO-9080-2003.pdf（32页珍藏版）》请在三一文库上搜索。
1、 Reference number ISO 9080:2003(E) ISO 2003 INTERNATIONAL STANDARD ISO 9080 First edition 2003-03-15 Plastics piping and ducting systems Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation Systmes de canalisations et de gaines en matires plas
2、tiques Dtermination de la rsistance hydrostatique long terme des matires thermoplastiques sous forme de tubes par extrapolation Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/12/2007 22
3、:48:20 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 9080:2003(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedde
4、d are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. De
5、tails of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem
6、 relating to it is found, please inform the Central Secretariat at the address given below. ISO 2003 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm,
7、 without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2003 Al
8、l rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/12/2007 22:48:20 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 9080:2003(E) ISO 2003 All
9、 rights reserved iii Contents Page Forewordiv Introduction v 1 Scope 1 2 Normative references . 1 3 Terms and definitions. 1 4 Acquisition of test data 3 5 Procedure 3 6 Example of calculation for a semi-crystalline polymer, software validation 7 7 Test report . 7 Annex A (normative) Methods of data
10、 gathering and analysis . 9 Annex B (normative) Automatic knee detection . 13 Annex C (informative) Example of application of SEM to stress rupture data. 15 Annex D (informative) SEM software 23 Bibliography . 24 Copyright International Organization for Standardization Provided by IHS under license
11、with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/12/2007 22:48:20 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 9080:2003(E) iv ISO 2003 All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide fede
12、ration of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that commi
13、ttee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordan
14、ce with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires
15、approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 9080 was prepared by Technical Com
16、mittee ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids, Subcommittee SC 5, General properties of pipes, fittings and valves of plastic materials and their accessories Test methods and basic specifications. It cancels and replaces ISO/TR 9080:1992, which has been technical
17、ly revised. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/12/2007 22:48:20 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 9080:2003(E) ISO 2003 All right
18、s reserved v Introduction General ISO/TR 9080, upon which this International Standard is based, is the result of considerable discussion within working group 10 of subcommittee 5 of technical committee 138 of the International Organization for Standardization (ISO) (referred to hereafter as ISO/TC 1
19、38/SC 5/WG 10), which was entrusted with the development of the standard, which represents an agreed compromise incorporating features of several accepted national procedures. Furthermore, it is emphasized that the standard extrapolation method (SEM) described is not intended to be used to disqualif
20、y existing procedures for arriving at design stresses or allowable pressures for pipelines made of plastics materials, or to disqualify pipelines made of materials proven by such procedures, which long years of experience have shown to be satisfactory. This SEM is meant to be used to qualify a mater
21、ial in pipe form prior to the introduction of such a material on the market. A software package has been developed for the SEM analysis as described in Annex A and Annex B. A Windows-based programme is available on diskette (see Annex D). NOTE Use of this software package is recommended. Principles
22、The suitability for use of a plastics pressure pipe is first of all determined by the performance under stress of its material of construction, taking into account the envisaged service conditions (e.g. temperature). It is conventional to express this by means of the hydrostatic (hoop) stress which
23、a plastics pipe made of the material under consideration is expected to be able to withstand for 50 years at an ambient temperature of 20 C using water as the internal test medium. The outside environment can be water or air. In certain cases, it is necessary to determine the value of the hydrostati
24、c strength at either shorter lifetimes or higher temperatures, or on occasion both. The method given in this International Standard is designed to meet the need for both types of estimate. The result obtained will indicate the lower prediction limit (LPL), which is the lower confidence limit of the
25、prediction of the value of the stress that can cause failure in the stated time at a stated temperature (the ultimate stress). NOTE The MRS value (at 20 C) is usually based on data obtained using water as the internal and external test medium. It is obvious that indeed all data are used for validati
26、on of regression curves at higher temperatures (e.g. 70 C), including the data obtained with air as the external medium (e.g. at 110 C). This International Standard provides a definitive procedure incorporating an extrapolation using test data at different temperatures analysed by multiple linear re
27、gression analysis. The results permit the determination of material-specific design values in accordance with the procedures described in the relevant system standards. This multiple linear regression analysis is based on the rate processes most accurately described by log10(stress) versus log10(tim
28、e) models. In order to assess the predictive value of the model used, it has been considered necessary to make use of the estimated 97,5 % lower prediction limit (LPL). The 97,5 % lower prediction limit is equivalent to the lower confidence limit of the 95 % confidence interval of the predicted valu
29、e. This convention is used in the mathematical calculations to be consistent with the literature. This aspect necessitates the use of statistical techniques. The method can provide a systematic basis for the interpolation and extrapolation of stress rupture characteristics at operating conditions di
30、fferent from the conventional 50 years at 20 C. Taking into account the extrapolation factors (see 5.1.4), the extrapolation time limit can go up to 100 years. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/99725450
31、01 Not for Resale, 04/12/2007 22:48:20 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 9080:2003(E) vi ISO 2003 All rights reserved It is essential that the medium used for pressurizing the pipe does not have an adverse effect on the pipe. In general, water is considere
32、d to be such a medium. Long consideration was given to deciding which variable should be taken as the independent variable to calculate the long-term hydrostatic strength. The choice was between time and stress. The basic question the method has to answer can be formulated in two ways as follows. a)
33、 What is the maximum stress (or pressure) that a given pipe system can withstand at a given temperature for a defined time? b) How long will a pipe system last when subjected to a defined stress (or pressure) at a given temperature? Both questions are relevant. If the test data for the pipe under st
34、udy does not show any scatter and if the pipe material can be described perfectly by the chosen empirical model, the regression with either time independence or stress independence will be identical. This is never the case because the circumstances of testing are never ideal nor will the material be
35、 100 % homogeneous. The observations will therefore always show scatter. The regressions calculated using the two optional independent variables will not be identical and the difference will increase with increasing scatter. The variable that is assumed to be most affected by the largest variability
36、 (scatter) is the time variable and it has to be considered as a dependent variable (random variable) in order to allow a correct statistical treatment of the data set in accordance with this method. However, for practical reasons, the industry prefers to present stress as a function of time as an i
37、ndependent variable. Use of the methods This extrapolation method is designed to meet the following two requirements: a) To estimate the lower prediction limit1) (at 97,5 % probability level) of the stress which a pipe made of the material under consideration is able to withstand for 50 years at an
38、ambient temperature of 20 C using water or air as the test environment. b) To estimate the value of the lower prediction limit (at 97,5 % probability level) of the stress, either at different lifetimes or at different temperatures, or on occasion both. There are several extrapolation models in exist
39、ence, which have different numbers of terms. This SEM will use only models with two, three or four parameters. Adding more terms could improve the fit but would also increase the uncertainty of the predictions. The SEM describes a procedure for estimating the lower prediction limit (at 97,5 % probab
40、ility level) whether a knee (which demonstrates the transition between type A and type B crack behaviour) is found or not (see Annex B). The materials have to be tested in pipe form for the method to be applicable. The final result of the SEM for a specific material is the lower prediction limit (at
41、 97,5 % probability level) of the hydrostatic strength, expressed in terms of the hoop stress, at a given time and a given temperature. 1) In various ISO documents, the lower prediction limit (LPL) is referred to as the lower confidence limit (LCL), where LCL is the 97,5 % lower confidence limit for
42、 the mean hydrostatic strength. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/12/2007 22:48:20 MDTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL S
43、TANDARD ISO 9080:2003(E) ISO 2003 All rights reserved 1 Plastics piping and ducting systems Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation 1 Scope This International Standard describes a method for estimating the long-term hydrostatic st
44、rength of thermoplastics materials by statistical extrapolation. The method is applicable to all types of thermoplastics pipe at applicable temperatures. It was developed on the basis of test data from pipe systems. The dimensions of the pipes to be tested may be specified in the relevant product/sy
45、stem standards and, if so, are included in the test report. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (i
46、ncluding any amendments) applies. ISO 1167, Thermoplastics pipes for the conveyance of fluids Resistance to internal pressure Test method ISO 2507-1:1995, Thermoplastics pipes and fittings Vicat softening temperature Part 1: General test method ISO 3126:2), Plastics piping systems Plastics piping co
47、mponents Measurement and determination of dimensions ISO 3146:2000, Plastics Determination of melting behaviour (melting temperature or melting range) of semi-crystalline polymers by capillary tube and polarizing-microscope methods 3 Terms and definitions For the purposes of this document, the follo
48、wing terms and definitions apply. 3.1 internal pressure p force per unit area, in bars, exerted by the medium in the pipe 2) To be published. (Revision of ISO 3126:1974) Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/12/2007 22:48:20 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 9080:2003(E) 2 ISO 2003 All rights reserved 3.2 stress force per unit area, in megapasca