《NF-EN-12373-9-1999-ENG.pdf》由会员分享，可在线阅读，更多相关《NF-EN-12373-9-1999-ENG.pdf（19页珍藏版）》请在三一文库上搜索。
1、NF EN 12373-9 janvier 1999 Ce document est usage exclusif et non collectif des clients Saga Web. Toute mise en rseau, reproduction et rediffusion, sous quelque forme que ce soit, mme partielle, sont strictement interdites. This document is intended for the exclusive and non collective use of Saga We
2、b customers. All network exploitation, reproduction and re-dissemination,even partial, whatever the form (hardcopy or other media), is strictly prohibited. Saga Web Pour THALES CORPORATE SERVICES SAS - EPM Client 04988312 le 16/7/2009 10:19 AFNOR 1999AFNOR 19991st issue 1999-01-P AFNOR 1999 All righ
3、ts reserved FE044128ISSN 0335-3931 NF EN 12373-9 January 1999 Classification index: A 91-455-9 European standard French standard Published and distributed by Association Franaise de Normalisation (AFNOR French standard institute) 11, avenue Francis de Pressens 93571 Saint-Denis La Plaine Cedex Tel.:
4、 + 33 (0)1 41 62 80 00 Fax: + 33 (0)1 49 17 90 00 www.afnor.fr ICS: 25.220.20; 77.120.10 Aluminium and aluminium alloys Anodizing Part 9: Measurement of wear resistance and wear index of anodic oxidation coatings using an abrasive wheel wear test apparatus F : Aluminium et alliages daluminium Anodis
5、ation Partie 9 : Dtermination de la rsistance lusure et de lindice dusure des couches doxyde anodiques par essai la roue abrasive D : Aluminium und Aluminiumlegierungen Anodisieren Teil 9: Messung der Abriebfestigkeit und der Abriebzahl von anodish erzeugten Oxidschichten durch Abriebprfung mit eine
6、m Schleifscheiben-Prfgert French standard approved by decision of the Director General of AFNOR on December 5, 1998 taking effect on January 5, 1999. Replaces the approved standard NF ISO 8251 dated July 1988. CorrespondenceThe European standard EN 12373-9:1998 has the status of French standard. Ana
7、lysisThis document specifies a method for determining the resistance to wear and the wear index of anodic oxidation coatings formed on a flat test specimen of aluminium or one of its alloys using a device comprising an abrasive wheel. DescriptorsTechnical International Thesaurus: metal finishing, an
8、odizing, aluminium, aluminium alloys, wear tests, determination, wear resistance, abrasion resistance, specimen preparation. ModificationsWith respect to document replaced, adoption of the European standard. Corrections NF EN 12373-9:1999 2 National foreword References to French standards The corres
9、pondence between the standards figuring in the clause “Normative references“ and the identical French standards is as follows: ISO 2360: NF EN ISO 2360 (classification index: A 91-113) EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12373-9 November 1998 ICS 25.220.20; 77.120.10 Descriptors:sur
10、face treatment, anodizing, aluminium, aluminium alloys, wear tests, determination, wear resistance, abrasion resistance, specimen preparation English version Aluminium and aluminium alloys - Anodizing - Part 9: Measurement of wear resistance and wear index of anodic oxidation coatings using an abras
11、ive wheel wear test apparatus Aluminium et alliages daluminium - Anodisation - Partie 9: Dtermination de la rsistance lusure et de lindice dusure des couches doxyde anodiques par essai la roue abrasive Aluminium und Aluminiumlegierungen - Anodisieren - Teil 9: Messung der Abriebfestigkeit und der Ab
12、riebzahl von anodisch erzeugten Oxidschichten durch Abriebprfung mit einem Schleifscheiben-Prfgert This European Standard was approved by CEN on 5 November 1998. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
13、 the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, Ger
14、man). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, F
15、inland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Central Secretariat: rue de Stassart, 36 B-1050 Brussels 1998 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12373-9:1998 E