《SAE-AS-7928-7-1999.pdf》由会员分享，可在线阅读，更多相关《SAE-AS-7928-7-1999.pdf（6页珍藏版）》请在三一文库上搜索。
1、SAE-AS7928/7 ADOPTION NOTICE SAE-AS7928/7, “TERMINAL LUG AND SPLICES, CONDUCTOR, CRIMP STYLE, COPPER, TERMINAL LUG, CRIMP STYLE, COPPER, UNINSULATED, RING TONGUE TYPE I, CLASS 1 FOR 175 DEG. C. TOTAL CONDUCTOR TEMPERATURE“, was adopted on 31-AUG-99 for use by the Department of Defense (DoD). Propose
2、d changes by DoD activities must be submitted to the DoD Adopting Activity: Commander, Naval Air Warfare Center, Aircraft Division, Code 414100B120-3, Highway 547, Lakehurst, NJ 08733-5100. Copies of this document may be purchased from the Society of Automotive Engineers 400 Commonwealth Drive Warre
3、ndale, Pennsylvania, United States, 15096-0001. http:/www.sae.org/_ Custodians:Adopting Activity: Navy - ASArmy - CR Navy - AS Air Force - 11 DLA - GS Reviewer Activities: Army - AV Navy - EC, MC, OS, SH FSC 5940 DISTRIBUTION STATEMENT A: Approved for public release; distribution is unlimited. Copyr
4、ight 1999 Society of Automotive Engineers, Inc.Printed in the U.S.A. All rights reserved QUESTIONS REGARDING THIS DOCUMENT: (724) 772-8510FAX: (724) 776-0243SAE WEB ADDRESS:http:/www.sae.org TO PLACE A DOCUMENT ORDER: (724) 776-4970 FAX: (724) 776-0790 400 Commonwealth Drive, Warrendale, PA 15096-00
5、01 SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising ther
6、efrom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. SHEET 1 OF 5 AS7928/7 THIRD ANGLE PROJECTION AEROSPACE STANDARD AS7928/7 ISSUED 19
7、99-04 TERMINAL LUG AND SPLICES, CONDUCTOR, CRIMP STYLE, COPPER, TERMINAL LUG, CRIMP STYLE, COPPER, UNINSULATED, RING TONGUE TYPE I, CLASS 1 FOR 175C TOTAL CONDUCTOR TEMPERATURE PREPARED BY SAE SUBCOMMITTEE AE-8C2PROCUREMENT SPECIFICATION: NONE FEDERAL SUPPLY CLASS 5940 NOTICE THIS DOCUMENT HAS BEEN
8、TAKEN DIRECTLY FROM U.S. MILITARY SPECIFICATION MIL-T-7928/7 AND CONTAINS ONLY MINOR EDITORIAL AND FORMAT CHANGES REQUIRED TO BRING IT INTO CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF SAE TECHNICAL STANDARDS. THE INITIAL RELEASE OF THIS DOCUMENT IS INTENDED TO REPLACE MIL-T-7928/7. ANY PART NUMB
9、ERS ESTABLISHED BY THE ORIGINAL SPECIFICATION REMAIN UNCHANGED. THE ORIGINAL MILITARY SPECIFICATION WAS ADOPTED AS AN SAE STANDARD UNDER THE PROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD (TSB) RULES AND REGULATIONS (TSB 001) PERTAINING TO ACCELERATED ADOPTION OF GOVERNMENT SPECIFICATIONS AND STAND
10、ARDS. TSB RULES PROVIDE FOR (A) THE PUBLICATION OF PORTIONS OF UNREVISED GOVERNMENT SPECIFICATIONS AND STANDARDS WITHOUT CONSENSUS VOTING AT THE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE EXISTING GOVERNMENT SPECIFICATION OR STANDARD FORMAT. UNDER DEPARTMENT OF DEFENSE POLICIES AND PROCEDURES, ANY
11、QUALIFICATION REQUIREMENTS AND ASSOCIATED QUALIFIED PRODUCTS LISTS ARE MANDATORY FOR DOD CONTRACTS. ANY REQUIREMENT RELATING TO QUALIFIED PRODUCTS LISTS (QPLS) HAS NOT BEEN ADOPTED BY SAE AND IS NOT PART OF THIS SAE TECHNICAL DOCUMENT. -,-,- 400 Commonwealth Drive, Warrendale, PA 15096-0001 TERMINAL
12、 LUG AND SPLICES, CONDUCTOR, CRIMP STYLE, COPPER, TERMINAL LUG, CRIMP STYLE, COPPER, UNINSULATED, RING TONGUE TYPE I, CLASS 1 FOR 175C TOTAL CONDUCTOR TEMPERATURE AEROSPACE STANDARD AS7928/7 SHEET 2 OF 5 AS7928/7 THE COMPLETE REQUIREMENTS FOR ACQUIRING THE TERMINALS DESCRIBED HEREIN SHALL CONSIST OF
13、 THIS DOCUMENT AND THE LATEST ISSUE OF SPECIFICATION MIL-T-7928. 400 Commonwealth Drive, Warrendale, PA 15096-0001 TERMINAL LUG AND SPLICES, CONDUCTOR, CRIMP STYLE, COPPER, TERMINAL LUG, CRIMP STYLE, COPPER, UNINSULATED, RING TONGUE TYPE I, CLASS 1 FOR 175C TOTAL CONDUCTOR TEMPERATURE AEROSPACE STAN
14、DARD AS7928/7 SHEET 3 OF 5 AS7928/7 TABLE I -,-,- 400 Commonwealth Drive, Warrendale, PA 15096-0001 TERMINAL LUG AND SPLICES, CONDUCTOR, CRIMP STYLE, COPPER, TERMINAL LUG, CRIMP STYLE, COPPER, UNINSULATED, RING TONGUE TYPE I, CLASS 1 FOR 175C TOTAL CONDUCTOR TEMPERATURE AEROSPACE STANDARD AS7928/7 S
15、HEET 4 OF 5 AS7928/7 REQUIREMENTS: 1.MATERIAL:SOFT COPPER, QQ-C-502, CLASS A COPPER TUBING, ASTM B75-68 GILDING METAL, 95 PERCENT COPPER, 5 PERCENT ZINC. 2.FINISH: TIN PLATED. SEE ACQUISITION SPECIFICATION. 3.QUALIFICATION TESTING: FOR QUALIFICATION, TERMINALS SHALL BE TESTED WITH ANY ONE OF THE FOL
16、LOWING WIRES: MIL-W-22759/1, 9 OR 11 OR MIL-W-81381/1, 3 OR 7, AND TOOLING AS FOLLOWS: MIL-C-22520/24 HAND CRIMPING TOOL. MIL-C-915 AND MIL-C-2194 CABLES MAY BE USED WITH MIL-C-22520/25 OR MIL-C-22520/24 HAND CRIMPING TOOL. 4.AVERAGE DIAMETER OF “E” AND “F” DIMENSIONS MUST BE WITHIN QUALIFICATION DI
17、MENSIONS: MAX AND MIN. DIMENSIONS DUE TO OVALIZATION MUST BE WITHIN 3% OF SPECIFICATION REQUIREMENTS. 5.WHERE SPLIT BARREL CONSTRUCTION IS USED, THE SPLIT SHALL BE PERMANENTLY SEALED AND SHALL NOT OPEN AS A RESULT OF CRIMPING. 6.PART NUMBER. THE PART NUMBERS SHALL CONSIST OF THE LETTER “M”, SPECIFIC
18、ATION SHEET NUMBER, AND DASH NUMBER. EXAMPLE OF PART NUMBER: M7928/7-2 TERMINAL TERMINAL FIT SIZE 22-18 WIRE WITH 0.190 STUD SIZE HOLE. NOTES: 1.DIMENSIONS IN INCHES. 2.METRIC EQUIVALENTS (TO THE NEAREST .01 mm) ARE GIVEN FOR GENERAL INFORMATION ONLY AND ARE BASED UPON 1 INCH = 25.4 mm. TABLE II (REF) -,-,- 400 Commonwealth Drive, Warrendale, PA 15096-0001 TERMINAL LUG AND SPLICES, CONDUCTOR, CRIMP STYLE, COPPER, TERMINAL LUG, CRIMP STYLE, COPPER, UNINSULATED, RING TONGUE TYPE I, CLASS 1 FOR 175C TOTAL CONDUCTOR TEMPERATURE AEROSPACE STANDARD AS7928/7 SHEET 5 OF 5 AS7928/7 TABLE III