《SAE-AS-33514A-2007.pdf》由会员分享，可在线阅读，更多相关《SAE-AS-33514A-2007.pdf（3页珍藏版）》请在三一文库上搜索。
1、 AEROSPACE STANDARD (R) FITTING END, STANDARD DIMENSIONS FOR FLARELESS TUBE CONNECTION AND GASKET SEAL AS33514 Copyright 2007 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, me
2、chanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1998-08 REAFFIR
3、MED 2007-01 REVISED 2007-05 THIRD ANGLE PROJECTION CUSTODIAN: SAE G-3/G-3B REV. A FEDERAL SUPPLY CLASS 4730 AS33514 SHEET 1 OF 3 REV. A PROCUREMENT SPECIFICATION: NONE SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering
4、 sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be rea
5、ffirmed, revised, or cancelled. SAE invites your written comments and suggestions. RATIONALE THIS STANDARD IS REVISED TO UPDATE THE DIMENSIONS IN TABLES FOR CLARITY. FIGURE 1 - STYLE E AND G Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not
6、for Resale, 12/04/2007 20:29:20 MSTNo reproduction or networking permitted without license from IHS -,-,- AEROSPACE STANDARD (R) FITTING END, STANDARD DIMENSIONS FOR FLARELESS TUBE CONNECTION AND GASKET SEAL AS33514 REV. A AS33514 SHEET 2 OF 3 REV. A FIGURE 1 - DETAIL AA AND BB TABLE 1 - DIMENSIONS
7、DATA (A TO J) SIZE NO. TUBE OD THREAD T AS8879 A .003 B GAGE C REF. D +.004 .000 E F +.002 .003 H .003 J .010 2 .125 .3125-24 UNJF-3A .093 .163 .189 .135 .563 .250 .188 .375 3 .188 .3750-24 UNJF-3A .125 .234 .267 .196 .625 .312 .422 4 .250 .4375-20 UNJF-3A .187 .293 .319 .261 .688 .364 .234 5 .313 .
8、5000-20 UNJF-3A .234 .356 .382 .324 .750 .426 .453 6 .375 .5625-18 UNJF-3A .297 .416 .441 .386 .813 .481 .250 .469 8 .500 .7500-16 UNJF-3A .422 .560 .601 .5141.000 .660 .305 .562 10 .625 .8750-14 UNJF-3A .500 .686 .727 .6411.125 .773 .625 12 .750 1.0625-12 UNJ-3A .656 .810 .852 .7661.375 +.003 .004
9、.945 .350 16 1.000 1.3125-12 UNJ-3A .8751.062 1.1021.0161.6251.195 20 1.250 1.6250-12UNJ-3A 1.0931.316 1.3551.2701.875 .016 1.507 .415 24 1.500 1.8750-12 UNJ-3A 1.3441.565 1.6041.5202.1251.756 32 2.000 2.5000-12 UNJ-3A 1.8132.068 2.1082.0222.750 .020 2.381 .485 .688 TABLE 1 - DIMENSIONS DATA (K TO Y
10、) V RAD SIZE NO. TUBE OD K .010 DIA M MAX RAD Q +.015 .000MAXMIN W MAX X .005 Y .010 2 .125 .549 .010 .005.128 .250 3 .188 .611 .063 .158 .310 4 .250 .674 .005 .174 .365 5 .313 .736 .075 .190 .425 6 .375 .799 .083 .193 .480 8 .500 .986 .094 .210 .660 10 .625 1.111 .107 .002 .255 .775 12 .750 1.361 .
11、253 .945 16 1.000 1.599 .010 .015 .010 .322 1.195 20 1.250 1.849 .325 1.505 24 1.500 2.095 .390 1.755 32 2.000 2.720 .015 .125 .030 .020 .003 .395 2.380 Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 20:29:20 MSTNo
12、reproduction or networking permitted without license from IHS -,-,- AEROSPACE STANDARD (R) FITTING END, STANDARD DIMENSIONS FOR FLARELESS TUBE CONNECTION AND GASKET SEAL AS33514 REV. A AS33514 SHEET 3 OF 3 REV. A NOTES: 1. CONCENTRICITY: D, C, AND T (PITCH DIAMETER) SHALL BE CONCENTRIC TO EACH OTHER
13、 WITHIN .008 TOTAL INDICATOR READING (TIR). F AND T (PITCH DIAMETER) SHALL BE CONCENTRIC TO EACH OTHER WITHIN .005 TIR. 2. SQUARENESS BETWEEN THREAD AND FACE OF HEX SHALL NOT EXCEED W WHEN MEASURED AT DIAMETER K. 3. SURFACE ROUGHNESS SHALL BE IN ACCORDANCE WITH ASME B46.1. 4. REMOVE ALL BURRS, SLIVE
14、RS AND SHARP EDGES. 5. DIMENSIONS ARE IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: ANGLES .5. 6. EXAMPLE OF DESIGN IDENTIFICATION NUMBER: AS33514 E 8 7. IN THE EVENT OF CONFLICT BETWEEN THE TEXT OF THIS STANDARD AND THE REFERENCES CITED HEREIN, THE TEXT OF THIS STANDARD SHALL TAKE PRECEDENCE.
15、8. THE CHANGE BAR ( l ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT. E = STYLE E S = STYLE S BASIC DESIGN NUMBER SIZE OF FITTING END IN 16THS Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 20:29:20 MSTNo reproduction or networking permitted without license from IHS -,-,-