《SAE-AS-5310A.pdf》由会员分享，可在线阅读，更多相关《SAE-AS-5310A.pdf（4页珍藏版）》请在三一文库上搜索。
1、 AEROSPACE STANDARD FITTING END, BULKHEAD, SPHERICAL, 37 FLARED TUBE CONNECTION DESIGN STANDARD AS5310 Copyright 2007 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical
2、, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1997-10 REAFFIRMED 2001
3、-12 REVISED 2007-11 THIRD ANGLE PROJECTION CUSTODIAN: SAE G-3/G-3B REV. A FEDERAL SUPPLY CLASS 4730 AS5310 SHEET 1 OF 4 REV. A PROCUREMENT SPECIFICATION: NONE /1/ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering scie
4、nces. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirm
5、ed, revised, or cancelled. SAE invites your written comments and suggestions. RATIONALE THIS STANDARD IS BEING REVISED TO ADD METRIC EQUIVALENT DIMENSIONS, CHANGE TOLERANCE, AND CHANGE DIMENSION TO CORRECT ERRORS. K T M ACD A (Z) /2/ B A (N) R W /3/ P SEALING SURFACE L R CY S TO DEPTH K VIEW A ENLAR
6、GED 2X 45 5 4X R .020 0.51 .005 0.13 63 1.6 C .005 0.127 A .005 0.127A .005 0.127A .005 0.127A FIGURE 1 - FITTING END, STYLE G Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 19:52:36 MSTNo reproduction or networking
7、 permitted without license from IHS -,-,- AEROSPACE STANDARD FITTING END, BULKHEAD, SPHERICAL, 37 FLARED TUBE CONNECTION DESIGN STANDARD AS5310 SHEET 2 OF 4 REV. A FIGURE 2 - FITTING END, STYLE H SAME AS STYLE G EXCEPT AS SHOWN TABLE 1A - DIMENSIONS A-K, INCH -POUND UNITS (IN) BASIC NO. AS5310 /10/
8、SIZE CODE (NOMINAL TUBE SIZE) T THREAD PER AS8879 A B +.015 -.000 C D E K .015 03 .188 .3750-24 UNJF-3A .104 - .111 .174 .277 .129 .595 .922 04 .250 .4375-20 UNJF-3A .168 - .175 .189 .355 .190 .658 1.016 05 .312 .5000-20 UNJF-3A .230 - .237 .189 .415 .255 .720 1.016 06 .375 .5625-18 UNJF-3A .293 - .
9、301 .193 .470 .320 .782 1.094 08 .500 .7500-16 UNJF-3A .387 - .395 .247 .650 .425 .970 1.250 10 .625 .8750-14 UNJF-3A .480 - .488 .261 .760 .540 1.093 1.391 12 .750 1.0625-12 UNJ-3A .604 - .614 .307 .930 .665 1.343 1.562 16 1.000 1.3125-12 UNJ-3A .839 - .851 .308 1.180 .915 1.593 1.562 20 1.250 1.62
10、50-12 UNJ-3A 1.073 - 1.086 .356 1.495 1.145 1.843 1.609 24 1.500 1.8750-12 UNJ-3A 1.307 - 1.320 .369 1.745 1.380 2.089 1.625 TABLE 1B - DIMENSIONS L-Z, INCH -POUND UNITS (IN) BASIC NO. AS5310 /10/ SIZE CODE L .015 M +.015 -.000 N R .015 S .015 P W Y Z /2/ 03 .094 .063 .160 .109 .500 .217 .312 .3678
11、- .3750 .075 04 .094 .075 .126 .125 .562 .219 .312 .4294 - .4375 .067 05 .094 .075 .096 .125 .625 .217 .312 .4919 - .5000 .064 06 .094 .083 .060 .141 .688 .223 .312 .5538 - .5625 .072 08 .125 .094 .130 .156 .875 .329 .475 .7406 - .7500 .092 10 .125 .107 .074 .172 1.000 .328 .475 .8647 - .8750 .089 1
12、2 .125 .125 .124 .188 1.188 .436 .632 1.0511 - 1.0625 .117 16 .125 .125 .000 .188 1.438 .436 .632 1.3011 - 1.3125 .118 20 .125 .125 .000 .188 1.750 .559 .800 1.6136 - 1.6250 .165 24 .125 .125 .000 .188 2.000 .640 .942 1.8636 - 1.8750 .155 Copyright SAE International Provided by IHS under license wit
13、h SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 19:52:36 MSTNo reproduction or networking permitted without license from IHS -,-,- AEROSPACE STANDARD FITTING END, BULKHEAD, SPHERICAL, 37 FLARED TUBE CONNECTION DESIGN STANDARD AS5310 SHEET 3 OF 4 REV. A TABLE 1A - DIMENSIONS A-
14、K, SI UNITS (MM) BASIC NO. AS5310 /10/ SIZE CODE (NOMINAL TUBE SIZE) T THREAD PER AS8879 A B +0.38 -0 C D E K .38 03 4.78 .3750-24 UNJF-3A 2.642 2.896 4.42 7.036 3.277 15.11 23.42 04 6.35 .4375-20 UNJF-3A 4.267 - 4.445 4.80 9.017 4.826 16.71 25.81 05 7.92 .5000-20 UNJF-3A 5.842 - 6.020 4.80 10.541 6
15、.477 18.29 25.81 06 9.53 .5625-18 UNJF-3A 7.442 - 7.645 4.90 11.938 8.128 19.86 27.79 08 12.70 .7500-16 UNJF-3A 9.830 - 10.033 6.27 16.510 10.795 24.64 31.75 10 15.88 .8750-14 UNJF-3A 12.192 - 12.395 6.63 19.304 13.716 27.76 35.33 12 19.05 1.0625-12 UNJ-3A 15.342 - 15.596 7.80 23.622 16.891 34.11 39
16、.68 16 25.40 1.3125-12 UNJ-3A 21.311 - 21.615 7.82 29.972 23.241 40.46 39.68 20 31.75 1.6250-12 UNJ-3A 27.254 - 27.584 9.04 37.973 29.083 46.81 40.87 24 38.10 1.8750-12 UNJ-3A 33.198 - 33.528 9.37 44.323 35.052 53.06 41.28 TABLE 1B - DIMENSIONS L-Z, SI UNITS (MM) BASIC NO. AS5310 /10/ SIZE CODE L .3
17、8 M +.38 -0 N R .38 S .38 P W Y Z /2/ 03 2.39 1.60 4.06 2.77 12.70 5.512 7.925 9.342 - 9.525 1.91 04 2.39 1.91 3.20 3.18 14.28 5.563 7.925 10.907 - 11.113 1.70 05 2.39 1.91 2.44 3.18 15.88 5.512 7.925 12.494 - 12.700 1.63 06 2.39 2.11 1.52 3.58 17.48 5.664 7.925 14.067 - 14.288 1.83 08 3.18 2.39 3.3
18、0 3.96 22.23 8.357 12.065 18.811 - 19.050 2.34 10 3.18 2.72 1.88 4.37 25.40 8.331 12.065 21.963 - 22.225 2.26 12 3.18 3.18 3.15 4.78 30.18 11.074 16.053 26.698 - 26.988 2.97 16 3.18 3.18 .00 4.78 36.53 11.074 16.053 33.048 - 33.338 3.00 20 3.18 3.18 .00 4.78 44.45 14.199 20.320 40.985 - 41.275 4.19
19、24 3.18 3.18 .00 4.78 50.80 16.256 23.927 47.335 - 47.625 3.94 Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 19:52:36 MSTNo reproduction or networking permitted without license from IHS -,-,- AEROSPACE STANDARD FIT
20、TING END, BULKHEAD, SPHERICAL, 37 FLARED TUBE CONNECTION DESIGN STANDARD AS5310 SHEET 4 OF 4 REV. A NOTES: /1/ INTENDED USE: THIS FITTING END IS DESIGNED TO MATE WITH A 37 INTERNAL FLARED TUBE FITTING PER AS1708 OR AS4325 IN ACCORDANCE WITH PROCUREMENT SPECIFICATION AS4841, UNLESS OTHERWISE STATED O
21、N THE PART STANDARD. THE FITTING END IS PHYSICALLY INTERCHANGEABLE WITH THE 37 FLARED TUBE FITTING END PER AS4396. /2/ DIMENSION “Z” DEFINES THE NOMINAL OVERLAP BETWEEN THE INTERNAL AND EXTERNAL FITTING ENDS OF THE MATED CONNECTION AND IS FOR DESIGN USE ONLY. /3/ THE SPHERICAL SEALING SURFACE SHALL
22、BE FREE OF FLAWS, NICKS, AND CHATTER MARKS WHEN VIEWED WITH THE UNAIDED EYE. 4. THE CHANGE BAR ( l ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL
23、TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT. 5. INTERPRETATION OF DRAWING PER ARP4296. 6. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M; REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 in 3.2 m Ra. 7. BREAK EDGES .003 0.08 TO .015
24、0.38 UNLESS OTHERWISE SPECIFIED. 8. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994. 9. DIMENSIONS IN INCHES MILLIMETERS. METRIC CONVERSIONS ARE IN INTERNATIONAL SYSTEM UNITS (SI). UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .005 0.127 ANGULAR DIMENSIONS 030. /10/ EXAMPLE OF DRAWING CAL
25、LOUT: a. TABULATED PART DRAWING: TUBE END PER AS5310 STYLE G b. INDIVIDUAL PART DRAWING: BASIC NUMBER STYLE DESIGNATION SIZE CODE, TUBE SIZE IN .062 1.575 INCREMENTS AS5310 G 08 Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 19:52:36 MSTNo reproduction or networking permitted without license from IHS -,-,-