《SAE-AS-9392-1998-R2007.pdf》由会员分享，可在线阅读，更多相关《SAE-AS-9392-1998-R2007.pdf（2页珍藏版）》请在三一文库上搜索。
1、SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefr
2、om, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. SHEET 1 OF 2 AS9392 THIRD ANGLE PROJECTION AEROSPACE STANDARD AS9392 ISSUED 1998-02 R
3、EAFFIRMED 2007-06 CUSHION, LOOP CLAMP - MULTIPLE, 3-TUBE, AMS 3303 PREPARED BY COMMITTEE E-25, GENERAL STANDARDS FOR AEROSPACE PROPULSION FEDERAL SUPPLY CLASS 5340 NOTICE THIS DOCUMENT HAS BEEN TAKEN DIRECTLY FROM U.S. MILITARY SPECIFICATION MS9392 AND CONTAINS ONLY MINOR EDITORIAL AND FORMAT CHANGE
4、S REQUIRED TO BRING IT INTO CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF SAE TECHNICAL STANDARDS. THE INITIAL RELEASE OF THIS DOCUMENT IS INTENDED TO REPLACE MS9392. ANY PART NUMBERS ESTABLISHED BY THE ORIGINAL SPECIFICATION REMAIN UNCHANGED. THE ORIGINAL MILITARY SPECIFICATION WAS ADOPTED AS AN
5、SAE STANDARD UNDER THE PROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD (TSB) RULES AND REGULATIONS (TSB 001) PERTAINING TO ACCELERATED ADOPTION OF GOVERNMENT SPECIFICATIONS AND STANDARDS. TSB RULES PROVIDE FOR (A) THE PUBLICATION OF PORTIONS OF UNREVISED GOVERNMENT SPECIFICATIONS AND STANDARDS WITHO
6、UT CONSENSUS VOTING AT THE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE EXISTING GOVERNMENT SPECIFICATION OR STANDARD FORMAT. ANY MATERIAL RELATING TO QUALIFIED PRODUCT LISTS HAS NOT BEEN ADOPTED BY SAE. THIS MATERIAL WAS PART OF THE ORIGINAL MILITARY SPECIFICATION AND IS REPRINTED HERE FOR HISTORIC
7、REFERENCE ONLY. RATIONALE THIS DOCUMENT HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE 5-YEAR REVIEW POLICY. Copyright 2007 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanic
8、al, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org Copyright SAE International
9、Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 21:09:45 MSTNo reproduction or networking permitted without license from IHS -,-,- CUSHION, LOOP CLAMP - MULTIPLE, 3-TUBE, AMS 3303 AEROSPACE STANDARD AS9392 SHEET 2 OF 2 AS9392 FIGURE 1 - CLAMP L
10、OOP CUSHION 1. MATERIAL: SILICONE RUBBER AMS 3303. 2. DIMENSIONS IN INCHES, UNLESS OTHERWISE SPECIFIED; TOLERANCES: LINEAR DIMENSIONS .010. 3. DO NOT USE UNASSIGNED PART NUMBERS. AS & AMS ARE SOCIETY OF AUTOMOTIVE ENGINEERING PUBLICATIONS. THIS STANDARD WAS DEVELOPED COOPERATIVELY WITH THE ENGINE AN
11、D PROPELLER UTILITY PARTS COMMITTEE OF THE SAE. TABLE 1 - DASH NUMBERS AND DIMENSIONS PART NO. NOMINAL TUBE SIZE A RAD +.010 .000 B RAD .005 C .005 D REF APPROX WEIGHT LB/100 MS9392-01 .125.062.125 .188 .375 .152 MS9392-02 .188.094.156 .250 .500 .222 MS9392-03 .250.125.219 .344 .688 .447 MS9392-04 .
12、312.156.250 .406 .812 .577 MS9392-05 .375.188.281 .469 .938 .684 MS9392-06 .438.219.312 .5311.062 .807 MS9392-07 .500.250.375 .6251.2501.218 MS9392-08 .562.281.406 .6881.3751.380 MS9392-09 .625.312.438 .7501.5001.540 MS9392-10 .688.344.469 .8121.6251.710 MS9392-11 .750.375.500 .8751.7501.900 MS9392-
13、12 .812.406.531 .9381.8752.080 MS9392-13 .875.438.5621.0002.0002.250 MS9392-14 .938.469.5941.0622.1252.450 MS9392-151.000.500.6251.1252.2502.640 Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 21:09:45 MSTNo reproduction or networking permitted without license from IHS -,-,-