《TIA-102.AABC-B-2-2007.pdf》由会员分享，可在线阅读，更多相关《TIA-102.AABC-B-2-2007.pdf（42页珍藏版）》请在三一文库上搜索。
1、 TIA STANDARD Project 25 Trunking Control Channel Messages Addendum - ISSI TIA-102.AABC-B-2 (Addendum 2 to TIA-102.AABC-B) August 2007 TELECOMMUNICATIONS INDUSTRY ASSOCIATION Representing the telecommunications industry in association with the Electronic Industries Alliance ANSI/TI A-102.AABC-B-2 Ap
2、proved: August 9, 2007 NOTICE TIA Engineering Standards and Publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obt
3、aining with minimum delay the proper product for their particular need. The existence of such Standards and Publications shall not in any respect preclude any member or non-member of TIA from manufacturing or selling products not conforming to such Standards and Publications. Neither shall the exist
4、ence of such Standards and Publications preclude their voluntary use by Non-TIA members, either domestically or internationally. Standards and Publications are adopted by TIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, TIA does not assume any li
5、ability to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard or Publication. This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Stand
6、ard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations before its use. (From Standards Proposal No. 3-4661-RV2-AD2, formulated under the cognizance of the TIA, TR-8 Mobile and Personal Private Radio Standards. TR-8.10 Subcommittee on Tru
7、nking and Conventional Control ). Published by TELECOMMUNICATIONS INDUSTRY ASSOCIATION Standards and Technology Department 2500 Wilson Boulevard Arlington, VA 22201 U.S.A. PRICE: Please refer to current Catalog of TIA TELECOMMUNICATIONS INDUSTRY ASSOCIATION STANDARDS AND ENGINEERING PUBLICATIONS or
8、call IHS USA and Canada (1-800-525-7052 ) International (303-790-0600) or search online at http:/www.tiaonline.org/standards/catalog/ All rights reserved Printed in U.S.A. NOTICE OF COPYRIGHT This document is copyrighted by the TIA. Reproduction of these documents either in hard copy or soft copy (i
9、ncluding posting on the web) is prohibited without copyright permission. For copyright permission to reproduce portions of this document, please contact TIA Standards Department or go to the TIA website (www.tiaonline.org) for details on how to request permission. Details are located at: http:/www.t
10、iaonline.org/standards/catalog/info.cfm#copyright OR Telecommunications Industry Association Standards (b) there is no assurance that the Document will be approved by any Committee of TIA or any other body in its present or any other form; (c) the Document may be amended, modified or changed in the
11、standards development or any editing process. The use or practice of contents of this Document may involve the use of intellectual property rights (“IPR”), including pending or issued patents, or copyrights, owned by one or more parties. TIA makes no search or investigation for IPR. When IPR consist
12、ing of patents and published pending patent applications are claimed and called to TIAs attention, a statement from the holder thereof is requested, all in accordance with the Manual. TIA takes no position with reference to, and disclaims any obligation to investigate or inquire into, the scope or v
13、alidity of any claims of IPR. TIA will neither be a party to discussions of any licensing terms or conditions, which are instead left to the parties involved, nor will TIA opine or judge whether proposed licensing terms or conditions are reasonable or non-discriminatory. TIA does not warrant or repr
14、esent that procedures or practices suggested or provided in the Manual have been complied with as respects the Document or its contents. If the Document contains one or more Normative References to a document published by another organization (“other SSO”) engaged in the formulation, development or
15、publication of standards (whether designated as a standard, specification, recommendation or otherwise), whether such reference consists of mandatory, alternate or optional elements (as defined in the TIA Engineering Manual, 4th edition) then (i) TIA disclaims any duty or obligation to search or inv
16、estigate the records of any other SSO for IPR or letters of assurance relating to any such Normative Reference; (ii) TIAs policy of encouragement of voluntary disclosure (see Engineering Manual Section 6.5.1) of Essential Patent(s) and published pending patent applications shall apply; and (iii) Inf
17、ormation as to claims of IPR in the records or publications of the other SSO shall not constitute identification to TIA of a claim of Essential Patent(s) or published pending patent applications. TIA does not enforce or monitor compliance with the contents of the Document. TIA does not certify, insp
18、ect, test or otherwise investigate products, designs or services or any claims of compliance with the contents of the Document. ALL WARRANTIES, EXPRESS OR IMPLIED, ARE DISCLAIMED, INCLUDING WITHOUT LIMITATION, ANY AND ALL WARRANTIES CONCERNING THE ACCURACY OF THE CONTENTS, ITS FITNESS OR APPROPRIATE
19、NESS FOR A PARTICULAR PURPOSE OR USE, ITS MERCHANTABILITY AND ITS NONINFRINGEMENT OF ANY THIRD PARTYS INTELLECTUAL PROPERTY RIGHTS. TIA EXPRESSLY DISCLAIMS ANY AND ALL RESPONSIBILITIES FOR THE ACCURACY OF THE CONTENTS AND MAKES NO REPRESENTATIONS OR WARRANTIES REGARDING THE CONTENTS COMPLIANCE WITH
20、ANY APPLICABLE STATUTE, RULE OR REGULATION, OR THE SAFETY OR HEALTH EFFECTS OF THE CONTENTS OR ANY PRODUCT OR SERVICE REFERRED TO IN THE DOCUMENT OR PRODUCED OR RENDERED TO COMPLY WITH THE CONTENTS. -,-,- TIA SHALL NOT BE LIABLE FOR ANY AND ALL DAMAGES, DIRECT OR INDIRECT, ARISING FROM OR RELATING T
21、O ANY USE OF THE CONTENTS CONTAINED HEREIN, INCLUDING WITHOUT LIMITATION ANY AND ALL INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF BUSINESS, LOSS OF PROFITS, LITIGATION, OR THE LIKE), WHETHER BASED UPON BREACH OF CONTRACT, BREACH OF WARRANTY, TORT (INCLUDING N
22、EGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE FOREGOING NEGATION OF DAMAGES IS A FUNDAMENTAL ELEMENT OF THE USE OF THE CONTENTS HEREOF, AND THESE CONTENTS WOULD NOT BE PUBLISHED BY TIA WITHOUT SUCH LIMITATIONS. -,-,- ii Foreword (This foreword is
23、 not part of this standard.) This document has been submitted to APCO/NASTD/FED by the Telecommunications Industry Association (TIA), as provided for in a Memorandum of Understanding (MOU) dated December 1993. That MOU provides that APCO/NASTD/FED will devise a Common System Standard for digital pub
24、lic safety communications (the Standard), and that TIA shall provide technical assistance in the development of documentation for the Standard. This document has been developed with inputs from the APCO/TIA Project 25 Interface Committee (APIC), the APIC Trunking Task Group, and TIA Industry members
25、. This document is being published because it is felt that there is an urgent need for technical information on the emerging digital techniques for Land Mobile Radio Service. This document describes enhancements to the control channel messages for trunked systems meeting the Project 25 requirements
26、in order to support the Project 25 ISSI. These definitions are necessary to insure interoperability of trunked radio units. As other documents describing the trunking protocol are developed, this document will be subject to change, Additional reason codes and additional messages covering working cha
27、nnel maintenance may be needed. Some efforts have been made to ensure accuracy, but it should be understood that conformance tests remain to be developed and proven. This document is a standard. It presents an overview of trunking messages which was recommended by TIA to APCO/NASTD/FED as being suit
28、able for use as part of their standard for a digital public safety radio system (Project 25). TIA expects that APCO/NASTD/FED shall establish and publish one or more standards for trunking operation. TIA-102.AABC-B-2 iii Table of Contents ADDENDUM INTRODUCTION 1 Addendum Scope 1 Addendum Revision Hi
29、story 1 Addendum References 2 1 INTRODUCTION 3 2 TRUNKING PACKET DESCRIPTION 3 3 CATEGORIZATION 3 4.0 VOICE SERVICE 3 4.1 Voice Service ISPs 3 4.2 Voice Service OSPs 3 4.2.1 Group Voice Channel Grant (GRP_V_CH_GRANT) 3 4.2.2 Group Voice Channel Grant Update (GRP_V_CH_GRANT_UPDT) 3 4.2.3 Group Voice
30、Channel Update-Explicit (GRP_V_CH_GRANT_UPDT_EXP) 3 4.2.4 Unit to unit Answer Request (UU_ANS_REQ) 3 4.2.5 Unit to Unit Voice Service Channel Grant (UU_V_CH_GRANT) 4 4.2.6 Telephone Interconnect Voice Channel Grant (TELE_INT_CH_GRANT) 6 4.2.7 Telephone Interconnect Answer Request (TELE_INT_ANS_REQ)
31、6 4.2.8 Unit to Unit Voice Channel Grant Update (UU_V_CH_GRANT_UPDT) 7 4.2.9 Tel. Interconnect Channel Grant Update (TELE_INT_CH_GRANT_UPDT) 9 5 DATA SERVICE 9 6 CONTROL AND STATUS SERVICES 9 6.1 Control and Status ISPs 9 6.1.1 Acknowledge Response - Unit (ACK_RSP_U) 9 6.1.2 Authentication Query (AU
32、TH_Q) 9 6.1.3 Authentication Response (AUTH_RSP) 9 6.1.4 Call Alert Request (CALL_ALRT_REQ) 9 6.1.5 Cancel Service Request (CAN_SRV_REQ) 10 6.1.6 Emergency Alarm Request (EMRG_ALRM_REQ) 13 6.1.7 Extended Function Response (EXT_FNCT_RSP) 13 6.1.8 Group Affiliation Query Response (GRP_AFF_Q_RSP) 13 6.
33、1.9 Group Affiliation Request (GRP_AFF_REQ) 13 6.1.10 Identifier Update Request (IDEN_UP_REQ) 13 6.1.11 Message Update Request (MSG_UPDT_REQ) 13 6.1.12 Protection Parameter Request (P_PARM_REQ) 13 6.1.13 Status Query Request (STS_Q_REQ) 13 6.1.14 Status Query Response (STS_Q_RSP) 13 6.1.15 Status Up
34、date Request (STS_UPDT_REQ) 13 6.1.16 Unit Registration Request (U_REG_REQ) 13 6.1.17 De-Registration Request (U_DE_REG_REQ) 13 6.1.18 Location Registration Request (LOC_REG_REQ) 13 6.1.19 Radio Unit Monitor Request (RAD_MON_REQ) 13 6.1.20 Roaming Address Request (ROAM_ADDR_REQ) 14 6.1.21 Roaming Ad
35、dress Response (ROAM_ADDR_RSP) 14 -,-,- TIA-102.AABC-B-2 iv 6.2 Control and Status OSPs 14 6.2.1 Acknowledge Response - FNE (ACK_RSP_FNE) 14 6.2.2 Adjacent Status Broadcast (ADJ_STS_BCST) 14 6.2.3 Authentication Command (AUTH_CMD) 14 6.2.4 Call Alert (CALL_ALRT) 14 6.2.5 Deny Response (DENY_RSP) 14
36、6.2.6 Extended Function Command (EXT_FNCT_CMD) 16 6.2.7 Group Affiliation Query (GRP_AFF_Q) 16 6.2.8 Group Affiliation Response (GRP_AFF_RSP) 16 6.2.9 Identifier Update (IDEN_UP) 20 6.2.10 Message Update (MSG_UPDT) 20 6.2.11 Network Status Broadcast (NET_STS_BCST) 20 6.2.12 Protection Parameter Broa
37、dcast (P_PARM_BCST) 20 6.2.13 Protection Parameter Update (P_PARM_UPDT) 20 6.2.14 Queued Response (QUE_RSP) 20 6.2.15 RFSS Status Broadcast (RFSS_STS_BCST) 21 6.2.16 Secondary Control Channel Broadcast (SCCB) 24 6.2.17 Status Query (STS_Q) 24 6.2.18 Status Update (STS_UPDT) 24 6.2.19 System Service
38、Broadcast (SYS_SRV_BCST) 24 6.2.20 Unit Registration Command (U_REG_CMD) 26 6.2.21 Unit Registration Response (U_REG_RSP) 26 6.2.21.1 Abbreviated Form 26 6.2.22 De-Registration Acknowledge (U_DE_REG_ACK) 27 6.2.23 Location Registration Response (LOC_REG_RSP) 27 6.2.24 Radio Unit Monitor Command (RAD
39、_MON_CMD) 27 6.2.25 Roaming Address Command (ROAM_ADDR_CMD) 27 6.2.26 Roaming Address Update (ROAM_ADDR_UPDT) 27 6.2.27 Time and Date Announcement (TIME_DATE_ANN) 27 6.2.28 Secondary Control Channel Broadcast - Explicit (SCCB_EXP) 27 6.2.29 Identifier Update (IDEN_UP_VU) for VHF/UHF Bands 27 ANNEX A
40、. CANCEL RESPONSE REASON CODES (NORMATIVE) 28 ANNEX B. DENY RESPONSE REASON CODES (NORMATIVE) 28 ANNEX C. QUEUED RESPONSE REASON CODES (NORMATIVE) 30 ANNEX D. ISP AND OSP LISTS (INFORMATIVE) 30 ANNEX E. LIST OF ACRONYMS (INFORMATIVE) 30 ANNEX F. TRUNKING CHANNEL ADDRESSING (INFORMATIVE) 30 TIA-102.A
41、ABC-B-2 v This page left intentionally blank. -,-,- TIA-102.AABC-B-2 1 ADDENDUM INTRODUCTION The purpose of this addendum is to update information contained in TIA-102.AABC-B, “Trunking Control Channel Messages“, based on the Project 25 ISSI feature. This addendum defines the trunking control channe
42、l message changes required to support the Project 25 ISSI feature of Project 25 digital trunked radio systems. Addendum Scope This addendum enhances trunking control channel messages to support: (1) identification of SUs using their full SUIDs in SU-to-SU call grants and call service cancellation re
43、quests; (2) assignment of a WGID and an AGID during affiliation to an SG whose home is in another WACN or System; (3) absence of valid target WUID when queuing or denying individual audience services involving an SU whose home is in another WACN or System; (4) inclusion of Twuid_validity in SYS_SRV_
44、BCST messages; (5) ISSI-related deny reason codes. This document will only include information relevant to the above-listed functionality. The reader is referred to TIA-102.AABC-B for all other pertinent information. The next complete revision of TIA-102.AABC-B will incorporate the changes contained
45、 in this addendum. Changes to TIA-102.AABC-B for this feature are described in this document starting at Section 1. Note that section numbers identified in this addendum directly translate to section numbers in the TIA-102.AABC-B, Trunking Control Channel Messages document. Addendum Revision History
46、 Table 0-1: Revision History Version Date Description Issue A August 18, 2006 Initial draft of ISSI Addendum TIA/EIA-102.AABC-B-4. Issue B December 7, 2006 Updated with resolutions from first round of comments. Issue C December 20, 2006 Minor updates to resolve several outstanding comments (non-ISSI
47、-related) against AABC. TIA-102.AABC-B-2 2 Issue D March 12, 2007 Incorporated agreement on RFSS R bit. Issue E March 23, 2007 Incorporated agreed to edit in 6.2.20. Issue F July 13, 2007 Resolved ballot comments, update approved for publication at Baltimore TIA meetings. Addendum References -,-,- T
48、IA-102.AABC-B-2 3 Addendum changes to TIA-102.AABC-B, Trunking Control Channel Messages, begin here. 1 Introduction Review of the existing text in this section and its subsections of TIA-102.AABC-B identified no change for this addendum. 2 Trunking Packet Description Review of the existing text in t
49、his section and its subsections of TIA-102.AABC-B identified no change for this addendum. 3 Categorization Review of the existing text in this section and its subsections of TIA-102.AABC-B identified no change for this addendum. 4.0 Voice Service Review of the existing text in this section of TIA-102.AABC-B identified no change for this addendum. 4.1 Voice Se