《【BS英国标准】BS EN 13744-2004 Surfaces for sports areas. Procedure for accelerated ageing by immersion in hot water.pdf》由会员分享，可在线阅读，更多相关《【BS英国标准】BS EN 13744-2004 Surfaces for sports areas. Procedure for accelerated ageing by immersion in hot water.pdf（8页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 13744:2004 Surfaces for sports areas Procedure for accelerated ageing by immersion in hot water The European Standard EN 13744:2004 has the status of a British Standard ICS 97.150; 97.220.10 ? Licensed Copy: Oxford Brookes ATHENS, Oxford Brookes University, 23/04/2009 06:15, U
2、ncontrolled Copy, (c) BSI BS EN 13744:2004 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 13 October 2004 BSI 13 October 2004 ISBN 0 580 44597 6 National foreword This British Standard is the official English language version of EN 13744:200
3、4. The UK participation in its preparation was entrusted to Technical Committee PRI/57, Surfaces for sports areas, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implemen
4、t international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does n
5、ot purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European c
6、ommittee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2
7、to 5 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. DateComments Licensed Copy: Oxford Brookes ATHENS, Oxford Brookes University, 23/04/2009 06:15, Uncontrolled Copy, (c) BSI EUROPEAN STA
8、NDARD NORME EUROPENNE EUROPISCHE NORM EN 13744 October 2004 ICS 97.150; 97.220.10 English version Surfaces for sports areas - Procedure for accelerated ageing by immersion in hot water Sols sportifs - Mthode de vieillissement acclr par immersion dans leau chaude Sportbden - Verfahren der beschleunig
9、ten Alterung durch Eintauchen in heies Wasser This European Standard was approved by CEN on 29 July 2004. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteratio
10、n. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translatio
11、n under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungar
12、y, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de S
13、tassart, 36 B-1050 Brussels 2004 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13744:2004: E Licensed Copy: Oxford Brookes ATHENS, Oxford Brookes University, 23/04/2009 06:15, Uncontrolled Copy, (c) BSI EN 13744:2004 (E) 2 Content
14、s Page Foreword3 1 Scope 4 2 Principle4 3 Apparatus .4 4 Test pieces .4 5 Procedure .4 6 Comparison tests.5 7 Calculation and expression of results.5 8 Test report5 Licensed Copy: Oxford Brookes ATHENS, Oxford Brookes University, 23/04/2009 06:15, Uncontrolled Copy, (c) BSI w w w . b z f x w . c o m
15、 EN 13744:2004 (E) 3 Foreword This document (EN 13744:2004) has been prepared by Technical Committee CEN/TC 217 “Surfaces for sports areas”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or
16、 by endorsement, at the latest by April 2005, and conflicting national standards shall be withdrawn at the latest by April 2005. It is one of two standards for procedures for ageing surfaces for sports areas. The other standard in this series has the following title: EN 13817, Surfaces for sports ar
17、eas Procedures for accelerated ageing by exposure to hot air According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
18、Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Licensed Copy: Oxford Brookes ATHENS, Oxford Brookes University, 23/04/2009 06:15, Uncontrolled Copy, (c)
19、 BSI w w w . b z f x w . c o m EN 13744:2004 (E) 4 1 Scope This document describes a procedure for subjecting test pieces taken from surfaces for sports areas to accelerated ageing by immersion in hot water. Test pieces are aged to permit a comparison of their physical characteristics before and aft
20、er ageing in accordance with European Standard test methods for surfaces for sports areas. This method is suitable for ageing all types of sports surfaces, except for wooden surfaces, using test pieces in the laboratory, but is primarily intended for ageing polymeric surfaces. The procedure allows a
21、 measure of the effect on the physical characteristics of the sports surface due to exposure to water at elevated temperatures to be made. NOTE Results from tests on materials which exhibit temporary changes in properties due to moisture should be interpreted with caution. 2 Principle Test pieces ar
22、e exposed to water at an elevated temperature to permit selected physical characteristics of the surface to be assessed before and after test. 3 Apparatus 3.1 Water bath, capable of being maintained at (70 2) C. 3.2 Small weights, to assist with immersion if necessary. 4 Test pieces Select, prepare
23、and condition the test piece(s) in accordance with the appropriate method of test. Test pieces shall be such that no mechanical, chemical or heat treatment will be required after their removal from the water bath. Any material used for marking test pieces shall not be applied in any critical area of
24、 the test piece and shall not damage the surface or be destroyed during ageing. NOTE Wherever possible, marking should be carried out after ageing of the test piece. 5 Procedure Immerse test pieces in the water bath (3.1) maintained at a temperature of (70 2) C, the test pieces being freely exposed
25、to the ageing environment on all sides. If necessary, use the small weights (3.2) to submerge the test pieces in the water bath. Leave the test pieces in the water bath for (336 2) h. Remove the test pieces from the water bath and condition them together with an un-aged sample for not less than 16 h
26、 and for no more than 6 d in a relaxed condition in accordance with the test method for the particular characteristic being assessed. NOTE Simultaneous ageing of different test pieces in the same water bath should be avoided, to prevent migration of anti-degradants or plasticizers, etc. Licensed Cop
27、y: Oxford Brookes ATHENS, Oxford Brookes University, 23/04/2009 06:15, Uncontrolled Copy, (c) BSI w w w . b z f x w . c o m EN 13744:2004 (E) 5 6 Comparison tests To compare properties before and after accelerated ageing, carry out tests on un-aged test pieces at the same time and under the same con
28、ditions as those on test pieces having been subjected to accelerated ageing. Only compare test pieces of similar dimensions and having approximately the same exposed areas. 7 Calculation and expression of results Calculate the results as specified by the appropriate method of test. If required, calc
29、ulate the percentage change in the property using the following expression: 100 = O OA C where C is the percentage change in the property; A is the aged value of the property, e.g. % impact absorption; O is the un-aged value of the property. 8 Test report The test report shall include the following:
30、 a) reference to this document, i.e. EN 13744:2004; b) reference to the procedure used to select the test pieces and determine their characteristics, e.g. a European Standard test method; c) complete identification of the surface tested including manufacturers reference, type and depth of supporting
31、 layers, and method of attachment and previous history; d) physical characteristics determined, with their values before and after ageing, and, if required, their percentage change, calculated in accordance with Clause 7; e) individual test results, if required. Licensed Copy: Oxford Brookes ATHENS,
32、 Oxford Brookes University, 23/04/2009 06:15, Uncontrolled Copy, (c) BSI w w w . b z f x w . c o m BS EN 13744:2004 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on
33、standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the qua
34、lity of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (
35、0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +4
36、4 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless oth
37、erwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products
38、 and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits
39、 contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/w
40、ww.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or
41、 transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these d
42、etails are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-. Licensed Copy: Oxford Brookes ATHENS, Oxford Brookes University, 23/04/2009 06:15, Uncontrolled Copy, (c) BSI