JIS-B-0205-4-2001-ENG.pdf

《JIS-B-0205-4-2001-ENG.pdf》由会员分享，可在线阅读，更多相关《JIS-B-0205-4-2001-ENG.pdf（9页珍藏版）》请在三一文库上搜索。

1、J IS JAPANESE INDUSTRIAL STANDARD Translated and Published by Japanese Standards Association IS0 general purpose metric screw threads - Part 4: Basic dimensions ICs 21.040.10 Reference number : JIS B 0205-4 : 2001 (E) 5s Copyright Japanese Standards Association Provided by IHS under license with JSA

2、Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/11/2007 00:26:38 MSTNo reproduction or networking permitted without license from IHS -,-,- B 0205-4 : 2001 (IS0 7241993) Foreword This translation has been made based on the original Japanese Industrial Standard established by t

3、he Minister of Economy, Trade and Industry through deliberations at the Japanese Industrial Standards Committee according to the proposal of establishing a Japanese Industrial Standard from The Japan Research Institute for Screw Threads and Fasteners (JFRI)/the Japanese Standards Association (JSA),

4、with a draft of Industrial Standard based on the provision of Article 12 Clause 1 of the Industrial Standardization Law. By this Standard, JIS B 0205:1997 and JIS B 0207:1982 were withdrawn and replaced with JIS B 0205 Part 1 to Part 4. This Standard has been made based on IS0 724:1993 IS0 general-p

5、urpose metric screw threads - Basic dimensions for the purposes of making easy to compare this Standard with International Standard; to prepare Japanese Industrial Standard conforming with International Standard; and to propose a draft of International Standard which is based on Japanese Industrial

6、Standard. JIS B 0205 series consist of 4 parts with the title of IS0 general purpose metric screw threads. JIS B 0205-1 Part 1: Basic profile JIS B 0205-2 Part 2: General plan JIS B 0205-3 Part 3 : Selected sizes for screws, bolts and nuts JIS B 0205-4 Part 4: Basic dimensions Date of Establishment:

7、 2001-12-20 Date of Public Notice in Official Gazette: 2001-12-20 Investigated by: Japanese Industrial Standards Committee Standards Board Technical committee on Machine Elements JIS B 0205-4:2001, First English edition published in 2002-06 Translated and published by: Japanese Standards Association

8、 4-1-24, Akasaka, Minato-ku, Tokyo, 107-8440 JAPAN In the event of any doubts arising as to the contents, the original JIS is to be the final authority. O JSA 2002 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,

9、electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. Printed in Japan Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/11/2007 00:26:38 M

10、STNo reproduction or networking permitted without license from IHS -,-,- JAPANESE INDUSTRIAL STANDARD JIS B 0205-4 : 2001 (IS0 724 : 1993) IS0 general purpose metric screw threads - Part 4: Basic dimensions Introduction This Japanese Industrial Standard has been prepared based on the second edition

11、of IS0 724 IS0 general-purpose metric screw threads - Basic dimen- sions published in 1993 without modifying the technical contents. The “Note“ underlined with dots is the matter not included in the original Inter- national standard. 1 Scope This Standard specifies the basic dimensions, in milimetre

12、s, of IS0 met- ric screw threads in accordance with JIS B 0205-2. The values refer to the basic profile in accordance with JIS B0205-1. Remarks: The International Standard corresponding to this Standard is as follows. In addition, symbols which denote the degree of correspondence in the contents bet

13、ween the relevant International Standard and JIS are IDT (identical), MOD (modified), and NEQ (not equivalent) according to ISO/IEC Guide 21. IS0 general-purpose metric screw threads - Basic dimensions (IDT) IS0 724: 1993 2 Normative references The following standards contain provisions which, throu

14、gh reference in this Standard, constitute provisions in this Standard. The most recent editions of the standards (including amendments) shall be applied. JIS B 0101 Screw threads and fasteners - Vocabulary Remarks: The items cited from IS0 5408:1983 Cylindrical screw threads - Vocabulary are equival

15、ent to the corresponding matters of the said standard. JIS B 0205-1 IS0 general purpose metric screw threads - Part 1: Basic profile Remarks: IS0 68-1:1998 I S 0 general purpose screw threads - Basic profile - JIS B 0205-2 IS0 general purpose metric screw threads - Part 2: General plan Remarks: IS0

16、261: 1998 IS0 general purpose screw threads - General plan is Part 1: Metric screw threads is identical with the said standard. identical with the said standard. 3 Definitions For the purposes of this Standard, the definitions given in JIS B O101 apply. 4 Symbols The following symbols are used. D ba

17、sic major diameter of internal thread (nominal diameter) d basic major diameter of external thread (nominal diameter) D2 basic pitch diameter of internal thread d2 basic pitch diameter of external thread Dl basic minor diameter of internal thread dl basic minor diameter of external thread H height o

18、f fundamental triangle P pitch Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/11/2007 00:26:38 MSTNo reproduction or networking permitted without license from IHS -,-,- 2 B 0205-4 : 2001 (IS0 724

19、: 1993) 5 Basic dimensions Dimensions shall be as shown in figure 1 and given in table 1 . Y7 Fig. 1 Basic dimensions The values of D2, dz, Dl and dl have been calculated from the following formulae and rounded, in table 1, to the third decimal place: 3 5 dz = d - 2 x s H = d - 0,649 5P dl = d - 2 x

20、 s H = d - 1,082 5P 3 5 8 D z = D - 2 x T H = D - 0,649 5P D l = D - 2 X - H = D - 1,082 5P Table 1 Basic dimensions Unit: mm . basic minor diameter of internal thread DI is equal to basic minor diameter of external thread dJ:- _-_- _-_- Copyright Japanese Standards Association Provided by IHS under

21、 license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/11/2007 00:26:38 MSTNo reproduction or networking permitted without license from IHS -,-,- 3 B 0205-4 : 2001 (IS0 724 : 1993) ?Jominal dia. Major dia. of external thread d Table 1 (continued) pitch Pitch P Dz, d

22、i diameter Unit: mm i dia. of internal thread Pitch diameter Dz, dz Nominal dia. = Major dia. of external thread d Minor dia. of internal thread Di 1.5 1.25 1 0.75 Pitch P 9.026 9.188 9.350 9.513 8.376 8.647 8.917 28 11 12 14 15 1.5 10.026 1 10.350 0.75 10.513 1.75 10.863 1.5 11.026 1.25 11.188 1 11

23、.350 2 12.701 1.5 13.026 1.25 13.188 1 13.350 1.5 14.026 1 14.350 16 17 18 20 2 14.701 1.5 15.026 1 15.350 1.5 16.026 1 16.350 2.5 16.376 2 16.701 1.5 17.026 1 17.350 2.5 18.376 2 18.701 1.5 19.026 1 19.350 17.835 18.376 18.917 42 2.5 2 1.5 1 20.376 20.701 21 .O26 21.350 24 25 26 27 3 22.051 2 22.70

24、1 1.5 23.026 1 23.350 2 23.701 1.5 24.026 1 24.350 1.5 25.026 3 25.051 2 25.701 1.5 26.026 1 26.350 20.752 22.376 21-835 22.917 Y 10 2 1.5 1 26.701 27.026 27.350 25.835 26.376 26.917 3.5 3 2 1.5 1 27.727 28.051 28.701 29.026 29.350 26.2 1 1 26.752 27.835 28.376 28.917 9.917 10.106 29.835 30.376 29.2

25、1 1 29.752 30.835 31.376 2 1.5 3.5 3 2 1.5 30.701 3 1 .O26 30.727 31.051 31.701 32.026 34.026 12.376 12.647 12.917 13.376 13.917 33.376 31.670 32.752 33.835 34.376 1.5 4 3 2 1.5 33.402 34.051 34.701 35.026 37.026 36.402 37.051 37.701 38.026 38.051 38.701 39.026 i , IT 15.917 1.5 4 3 2 1.5 36.376 34.

26、670 35.752 36.835 37.376 36.752 37.835 38.376 15.294 15.835 16.376 16.917 17.294 40 3 2 1.5 4.5 4 3 2 1.5 39.077 39.402 40.051 40.701 41.026 37.129 37.670 38.752 39.835 40.376 22 19.294 II 4.5 4 3 2 1.5 42.077 42.402 43.051 43.701 44.026 40.129 40.670 41.752 42.835 43.376 20.376 20.917 5 4 3 2 1.5 4

27、4.752 45.402 46.051 46.701 47.026 42.587 43.670 44.752 45.835 46.376 23.917 24.376 23.752 24.835 3 2 1.5 48.051 48.701 49.026 46.752 47.835 48.376 25.376 Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale

28、, 03/11/2007 00:26:38 MSTNo reproduction or networking permitted without license from IHS -,-,- 4 B 0205-4 : 2001 (IS0 724 : 1993) Pitch diameter D2, dz Table 1 (continued) i dia. Nominal dia. of internal = Major dia. of external thread thread d Unit: mm 48.752 49.402 50.051 50.701 51.026 52.402 53.

29、051 53.701 54.026 Pitch P 49.835 50.376 50.670 51.752 52.835 53.376 Pitch P 52.428 53.402 54.051 54.701 55.026 55.402 56.051 56.701 57.026 56.428 57.402 58.051 5 8 . 7 0 1 59.026 59.402 60.051 60.701 61.026 Pitch diameter D2, dz 50.046 76 51.670 52.752 53.835 54.376 53.670 78 54.752 80 55.835 56.376

30、 54.046 55.670 56.752 82 57.835 85 58.376 57.670 58.752 59.835 90 60.376 Minor dia. of internal thread Di I Nominal dia. = Major dia. of external thread d 52 55 56 58 60 62 64 65 68 70 6 4 3 2 1 . 5 4 3 2 1 . 5 68.103 69.402 70.051 70.701 7 1 .O26 72.402 73.051 73.701 74.026 72.103 73.402 74.051 74.

31、701 75.026 76.700 65.505 67.670 68.752 69.835 70.376 70.670 71.752 72.835 73.376 69.505 71.670 72.752 73.835 74.376 75.835 5 4 3 2 1 . 5 4 3 2 1 . 5 5 . 5 4 3 2 1 . 5 6 4 3 2 1 . 5 4 3 2 1 . 5 2 6 4 3 2 1 . 5 76.103 77.402 78.051 78.701 79.026 73.505 75.670 76.752 77.835 78.376 5 . 5 4 3 2 1 . 5 4 3

32、 2 1 . 5 4 4 80.701 79.835 81.103 82.402 83.051 83.701 86.103 87.402 88.051 88.701 78.505 80.670 81.752 82.835 83.505 85.670 86.752 87.835 6 4 3 2 1 . 5 60.103 57.505 61.402 59.670 62.051 60.752 95 62.701 61.835 63.026 62.376 62.402 60.670 63.051 61.752 100 63.701 62.835 64.026 63.376 64.103 61.505

33、65.402 63.670 105 66.051 64.752 66.701 65.835 67.026 66.376 - 91.103 92.402 93.051 93.701 88.505 90.670 91.752 92.835 4 3 2 1 . 5 6 4 3 2 1 . 5 6 4 3 2 1 . 5 %.lo3 97.402 98.051 98.701 93.505 95.670 %.752 97.835 101.103 102.402 103.051 103.701 98.505 100.670 101.752 102.835 106.103 107.402 108.051 1

34、08.701 103.505 105.670 106.752 107.835 66.103 67.402 65.670 68.051 66.752 68.701 67.835 Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/11/2007 00:26:38 MSTNo reproduction or networking permitted w

35、ithout license from IHS -,-,- 5 B 0205-4 : 2001 (IS0 724 : 1993) Pitch P Table 1 (continued) Pitch diameter Dz, d2 Unit: mm i dia. of internal thread 108.505 110.670 11 1.752 112.835 113.505 115.670 116.752 117.835 116.340 118.505 120.670 121.752 122.835 121.340 Vominal dia. = Major dia. of external

36、 thread d Nominal dia. pitch Pitch = Major dia. P Dz, dz of external thread d 170 8 164.804 6 166.103 4 167.402 3 168.051 175 6 171.103 4 172.402 3 173.051 180 8 174.804 6 176.103 4 177.402 3 178.051 185 6 181.103 4 182.402 3 183.051 diameter Minor dia. of internal thread Di 6 4 3 2 111.103 112.402

37、113.051 113.701 6 4 3 2 8 6 4 3 2 8 6 4 3 2 6 4 3 2 8 6 4 3 2. 6 4 3 2 8 6 4 3 2 144.804 146.103 147.402 148.051 148.701 141.103 142.402 143.051 143.701 123.505 125.670 126.752 127.835 128.505 130.670 131.752 132.835 131.340 133.505 135.670 136.752 137.835 138.505 140.670 141.752 142.835 141.340 143

38、.505 145.670 146.752 147.835 148.505 150.670 151.752 151.340 153.505 155.670 190 8 184.804 6 186.103 4 187.402 3 188.051 191.103 4 192.402 3 193.051 200 8 194.804 6 1%.103 4 197.402 3 198.051 205 6 201.103 4 202.402 3 203.051 210 8 204.804 6 206.103 4 207.402 3 208.051 211.103 4 212.402 3 213.051 22

39、0 8 214.804 216.103 6 4 217.402 218.051 3 225 6 22 1 .lo3 4 222.402 3 223.051 195 , 6 215 6 156.752 158.505 -i 160.670 230 8 6 4 224.804 226.103 227.402 161.752 13 I 228.051 115 161.340 163.505 165.670. 166.752 168.505 170.670 17 1.752 120 116.103 117.402 118.051 118.701 119.804 121.103 122.402 123.

40、051 123.701 124.804 126.103 127.402 128.051 128.701 131 .lo3 132.402 133.05 1 133.701 171.340 173.505 175.670 176.752 125 178.505 180.670 181.752 130 181.340 183.505 185.670 186.752 188.505 190.670 191.752 135 191.340 193.505 195.670 1%.752 198.505 200.670 201.752 140 134.804 136.103 137.402 138.051

41、 138.701 145 20 1.340 203.505 205.670 206.752 150 208.505 210.670 211.752 211.340 213.505 215.670 216.752 218.505 220.670 221.752 155 151 -103 152.402 153.051 154.804 156.103 157.402 158.051 160 221.340 223.505 225.670 226.752 165 161 .lo3 162.402 163.051 Copyright Japanese Standards Association Pro

42、vided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/11/2007 00:26:38 MSTNo reproduction or networking permitted without license from IHS -,-,- 6. B 0205-4 : 2001 (IS0 724 : 1993) Pitch diameter Dz, dz 261.103 262.402 264.804 266.103 267.402 271.

43、103 272.402 274.804 276.103 277.402 281.103 282.402 284.804 286.103 287.402 291.103 292.402 294.804 2%.103 297.402 Table 1 (concluded) Unit: mn Minor dia. of internal thread Di 258.505 260.670 261.340 263.505 265.670 268.505 270.670 271.340 273.505 275.670 278.505 280.670 281 340 283.505 285.670 288

44、.505 290.670 291.340 293.505 295.670 i dia. Nominal dia. pitch Nominal dia. pitch Pitch = Major dia. diameter of internal = dia. of external of external thread d 1 p 1 D2 d2 i thread 11 thread d 1 241.103 242.402 243.051 244.804 246.103 247.402 248.051 251.103 252.402 254.804 256.103 i 257.402 231.1

45、03 232.402 233.051 238.505 280 8 240.670 6 241.752 4 241.340 285 6 243.505 4 245.670 290 8 246.752 6 248.505 4 250.670 295 6 251.340 4 253.505 300 8 255.670 6 234.804 236.103 237.402 238.051 231.752 231.340 233.505 235.670 275 236.752 4 245 250 255 260 6 4 3 8 6 4 Y I 1 14 Copyright Japanese Standar

46、ds Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/11/2007 00:26:38 MSTNo reproduction or networking permitted without license from IHS -,-,- Errata for JIS (English edition) are printed in Standarcfizution Journal, published

47、monthly by the Japanese Standards Association, and also provided to subscribers of JIS (English edition) in Monthly Information. Errata will be provided upon request, please contact: Standardization Promotion Department, Japanese Standards hociation 4-1-24, Akasaka, Minato-ku, Tokyo, 107-8440 JAPAN TEL. 03-3583-8002 FAX. 03-3583-0462 100% Recycied paper Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/11/2007 00:26:38 MSTNo reproduction or networking permitted without license from IHS -,-,-