《BS-EN-ISO-11608-4-2007.pdf》由会员分享，可在线阅读，更多相关《BS-EN-ISO-11608-4-2007.pdf（22页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN ISO 11608-4:2007 Pen-injectors for medical use Part 4: Requirements and test methods for electronic and electromechanical pen-injectors The European Standard EN ISO 11608-4:2007 has the status of a British Standard ICS 11.040.20; 11.040.25 ? Licensed Copy: London South Bank Un
2、iversity, London South Bank University, Fri Oct 05 02:17:04 GMT+00:00 2007, Uncontrolled Copy, (c) BSI BS EN ISO 11608-4:2007 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 28 September 2007 BSI 2007 ISBN 978 0 580 54214 5 National foreword
3、This British Standard is the UK implementation of EN ISO 11608-4:2007. It is identical to ISO 11608-4:2006. The UK participation in its preparation was entrusted to Technical Committee CH/84, Catheters and syringes. A list of organizations represented on this committee can be obtained on request to
4、its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Amendments issued since publication Amd. No. DateComments Licen
5、sed Copy: London South Bank University, London South Bank University, Fri Oct 05 02:17:04 GMT+00:00 2007, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 11608-4 August 2007 ICS 11.040.25 English Version Pen-injectors for medical use - Part 4: Requirements and tes
6、t methods for electronic and electromechanical pen-injectors (ISO 11608-4:2006) Stylos-injecteurs usage mdical - Partie 4: Exigences et mthodes dessai pour stylos-injecteurs lectroniques et lectro-mcaniques (ISO 11608-4:2006) Pen-Injektoren zur medizinischen Anwendung - Teil 4: Anforderungen an und
7、Prfverfahren fr elektronische und elektromechanische Pen-Injektoren (ISO 11608-4:2006) This European Standard was approved by CEN on 9 August 2007. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of
8、 a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A vers
9、ion in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, De
10、nmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALI
11、SATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2007 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 11608-4:2007: E Licensed Copy: London South Bank University, London South Bank Uni
12、versity, Fri Oct 05 02:17:04 GMT+00:00 2007, Uncontrolled Copy, (c) BSI Foreword The text of ISO 11608-4:2006 has been prepared by Technical Committee ISO/TC 84 “Devices for administration of medicinal products and intravascular catheters” of the International Organization for Standardization (ISO)
13、and has been taken over as EN ISO 11608-4:2007 by Technical Committee CEN/TC 205 “Non-active medical devices“, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest
14、 by February 2008, and conflicting national standards shall be withdrawn at the latest by February 2008. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all s
15、uch patent rights. ISO 11608-4 consists of the following parts under the general title “Pen-injectors for medical use”: Part 1: Pen-injectors - Requirements and test methods Part 2: Needles - Requirements and test methods Part 3: Finished cartridges - Requirements and test methods Part 4: Requiremen
16、ts and test methods for electronic and electromechanical pen-injectors According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estoni
17、a, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 11608-4:2006 has been approved by CEN
18、 as EN ISO 11608-4:2007 without any modifications. EN ISO 11608-4:2007 Licensed Copy: London South Bank University, London South Bank University, Fri Oct 05 02:17:04 GMT+00:00 2007, Uncontrolled Copy, (c) BSI Reference number ISO 11608-4:2006(E) INTERNATIONAL STANDARD ISO 11608-4 First edition 2006-
19、03-15 Pen-injectors for medical use Part 4: Requirements and test methods for electronic and electromechanical pen-injectors Stylos-injecteurs usage mdical Partie 4: Exigences et mthodes dessai pour stylos-injecteurs lectroniques et lectro-mcaniques EN ISO 11608-4:2007 Licensed Copy: London South Ba
20、nk University, London South Bank University, Fri Oct 05 02:17:04 GMT+00:00 2007, Uncontrolled Copy, (c) BSI ii Licensed Copy: London South Bank University, London South Bank University, Fri Oct 05 02:17:04 GMT+00:00 2007, Uncontrolled Copy, (c) BSI iii Contents Page Foreword iv Introduction v 1 Scop
21、e . 1 2 Normative references. 1 3 Terms and definitions. 2 4 Symbols and abbreviated terms . 2 5 General requirements. 2 6 Test conditions . 2 7 Preconditioning of pen-injectors 2 8 Reagent and apparatus 5 9 Determination of dose accuracy. 5 10 Freedom from defects 6 11 Determination of electromagne
22、tic compatibility. 7 12 Electrical safety. 7 13 Visual inspection 8 14 Functional inspection. 8 15 Test report . 8 16 Information supplied by the manufacturer 9 Bibliography. 10 EN ISO 11608-4:2007 Licensed Copy: London South Bank University, London South Bank University, Fri Oct 05 02:17:04 GMT+00:
23、00 2007, Uncontrolled Copy, (c) BSI iv Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member bod
24、y interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrote
25、chnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by
26、 the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rig
27、hts. ISO shall not be held responsible for identifying any or all such patent rights. ISO 11608-4 was prepared by Technical Committee ISO/TC 84, Devices for administration of medicinal products and intravascular catheters. ISO 11608 consists of the following parts, under the general title Pen-inject
28、ors for medical use: Part 1: Pen-injectors Requirements and test methods Part 2: Needles Requirements and test methods Part 3: Finished cartridges Requirements and test methods Part 4: Requirements and test methods for electronic and electromechanical pen-injectors EN ISO 11608-4:2007 Licensed Copy:
29、 London South Bank University, London South Bank University, Fri Oct 05 02:17:04 GMT+00:00 2007, Uncontrolled Copy, (c) BSI v Introduction This part of ISO 11608 covers electro-mechanical driven injectors not covered by part 1 of ISO 11608. These injectors are mainly intended to administer medicinal
30、 products to humans. This part of ISO 11608 provides performance requirements regarding essential aspects of the design so that variations of such injectors are not unnecessarily restricted. The sampling plans for inspection selected for this part of ISO 11608 are intended to verify, at a high confi
31、dence level, the manufacturers ability to manufacture one “lot” of injectors that conforms to the critical product attributes. These sampling plans for inspection do not intend to replace the more general manufacturing quality systems practices widely used in production, e.g. the ISO 9000 series. Ma
32、terials to be used for the construction of these injectors are not specified, as their selection, to some extent, will depend upon the design, the intended use and the manufacturing process selected by the manufacturer. All materials used in these injectors which come in contact with the end-user mu
33、st be non-toxic and biocompatible. In some countries, national regulations may exist and their requirements may supersede or add up to this part of ISO 11608. In relation to specification limits and dose accuracy, the ISO directives (Part 2, A3 and A13) require that the VIM1 and GUM2 principles are
34、used and incorporated in all future standards and future revisions of existing standards. The reorganization to be done in relation to this will not affect the technical content of the standards, and only the terminology shall be changed to correspond to VIM, and the principles shall be changed to c
35、orrespond to GUM. However, with this part of ISO 11608, ISO/TC 84 has decided to await the revision of the ISO 11608 series where the principles will be incorporated in all parts to conform to applicable requirements. EN ISO 11608-4:2007 Licensed Copy: London South Bank University, London South Bank
36、 University, Fri Oct 05 02:17:04 GMT+00:00 2007, Uncontrolled Copy, (c) BSI blank Licensed Copy: London South Bank University, London South Bank University, Fri Oct 05 02:17:04 GMT+00:00 2007, Uncontrolled Copy, (c) BSI 1 Pen-injectors for medical use Part 4: Requirements and test methods for electr
37、onic and electromechanical pen-injectors 1 Scope This part of ISO 11608 specifies requirements and test methods for electromechanically driven injectors intended to be used with needles and with replaceable or non-replaceable cartridges. The injector may be for single-use or multiple-use. The inject
38、or system is intended to deliver medication to an end-user by self-administration or with assistance. This part of ISO 11608 is neither applicable for needle-free injectors (as covered in ISO 21649) nor infusion pumps (as covered in IEC 60601-2-24). This part of ISO 11608 is not applicable for devic
39、es that are capable of operating while connected to an external power supply. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the refe
40、renced document (including any amendments) applies. ISO 11608-1:2000, Pen-injectors for medical use Part 1: Pen-injectors Requirements and test methods IEC 60068-2-27:1987, Environmental testing Part 2: Tests. Test Ea and guidance: Shock IEC 60068-2-30:1980, Environmental testing Part 2-30: Tests Te
41、st Db: Damp heat, cyclic (12 h + 12 h cycle) IEC 60068-2-64:1993, Environmental testing Part 2: Test methods Test Fh: Vibration, broad-band random (digital control) and guidance IEC 60529:2001, Degrees of protection provided by enclosures (IP Code) IEC 60601-1:1988, Edition 2: Medical electrical equ
42、ipment Part 1: General requirements for safety (+ AMD 1:1991 + AMD. 2: 1995) IEC 60601-1-1:2000, Medical electrical equipment Part 1-1: General requirements for safety Collateral standard: Safety requirements for medical electrical systems IEC 60601-1-2:2001, Medical electrical equipment Part 1-2: G
43、eneral requirements for safety Collateral standard: Electromagnetic compatibility Requirements and tests EN ISO 11608-4:2007 Licensed Copy: London South Bank University, London South Bank University, Fri Oct 05 02:17:04 GMT+00:00 2007, Uncontrolled Copy, (c) BSI 2 IEC 60721-3-7:1995, Classification
44、of environmental conditions Part 3: Classification of groups of environmental parameters and their severities Portable and non-stationary use IEC 61000-4-2:2001, Electromagnetic compatibility (EMC) Part 4-2: Testing and measurement techniques Electrostatic discharge immunity test 3 Terms and definit
45、ions For the purposes of this document the terms and definitions given in ISO 11608-1 and the following apply. 3.1 drive system electromechanical mechanism responsible for expelling the dose 3.2 pen-injector pen-injector with an electromechanical drive system 4 Symbols and abbreviated terms See Clau
46、se 4 of ISO 11608-1:2000. 5 General requirements See Clause 5 of ISO 11608-1:2000. 6 Test conditions 6.1 Standard atmosphere See 6.1 of ISO 11608-1:2000. 6.2 Cool atmosphere See 6.2 of ISO 11608-1:2000. 6.3 Hot atmosphere See 6.3 of ISO 11608-1:2000. 7 Preconditioning of pen-injectors 7.1 Preconditi
47、oning in dry heat atmosphere See 7.1 of ISO 11608-1:2000. 7.2 Preconditioning in cold storage atmosphere See 7.2 of ISO 11608-1:2000. EN ISO 11608-4:2007 Licensed Copy: London South Bank University, London South Bank University, Fri Oct 05 02:17:04 GMT+00:00 2007, Uncontrolled Copy, (c) BSI 3 7.3 Pr
48、econditioning in cyclical atmosphere See 7.3 of ISO 11608-1:2000. 7.4 Preconditioning by free fall See 7.4 of ISO 11608-1:2000. 7.5 Preconditioning by vibration Instead of the vibration test as described in 7.5 of ISO 11608-1:2000, the following applies. Unpack and prepare 5 pen-injectors according
49、to the instructions for use with a new cartridge. Place the pen-injectors in the box or pouch for transport as instructed by the manufacturer. Subject the pen-injectors to vibration in accordance with IEC 60068-2-64. Subject the pen-injectors to the conditions specified in IEC 60721-3-7:1995 Class 7M3, as follows: acceleration spectral density 3 m2/s3, frequency range 10 Hz to 200 Hz; acceleration spectral dens